We will reply to your message within an hour.
Push or pull the plunger to hold your workpiece from the side.
Smaller than standard push/pull toggle clamps, these are often used for electronics and small fixturing applications.
Secure your workpiece from the side by fully extending the plunger, and push a lever to lock the handle in place.
Smaller than standard push toggle clamps, these are often used for electronics and small fixturing applications.
Pull the handle backward to push the plunger forward. These clamps secure when the plunger is fully extended to hold your workpiece from the side.
A highly durable construction with hardened steel pivot pins and bushings provides a long service life.
The handle can be rotated 125° for easier access or extra clearance above the clamp.
Hold workpieces of different thicknesses without adjustment.
Moving parts are protected by a metal cover when the clamp is engaged to prevent dirt and dust from clogging the clamp.
Panel mount through a hole with the included nut, or drill and tap a hole to flush mount. A pushing or pulling motion holds workpieces from the side.
Push the lever to lock the handle and prevent accidental opening.
Secure these clamps to a rail or bar.
The plunger can be locked at any position along its travel.
Drill a hole to mount these clamps through a surface and secure the mounting flange with screws. The plunger can be locked at any position along its travel.
Use for repetitive clamping and in production environments or hard-to-reach locations.
Mount these clamps to a bench top or other surface to keep workpieces in place.
A nonreflective black oxide finish prevents glare that can interfere with machine vision systems.
Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.
Reduce the chance of getting pinched when unclamping. These clamps have more space between the handle and the arm than other low-profile toggle clamps.
The handle locks in a horizontal position for more clearance above the clamp than standard hold-down toggle clamps.
Often used when assembling small parts, these small clamps have the holding strength of a full-size clamp.
Weld these clamps to the side of an object or drill your own holes in the mounting plate and bolt into place.
Bolt to the side of an object. Often used to clamp lids and covers on containers.
The handle locks in a horizontal position for more clearance above the clamp.
The mounting base secures these clamps to a rail or bar.
Mount these clamps below a surface.
Two sets of mounting holes allow mounting on the bottom or side.
These clamps have mounting holes on the bottom.
Suitable for production applications, these clamps have double the service life of other air-powered toggle clamps.
The base fits into round or square holes on most workholding tables for clamping anywhere on the work surface.
Mount the base to a work surface using screws.
Instead of a step block, support these clamps using a screw, leveling mount, or any other threaded object.
Eliminating the need for step blocks or other rear support, the pivoting rocker clamps workpieces of various thicknesses.
Use with T-slot nuts or bolts and a support to secure a workpiece, vise, or fixture to a machine table.
The stepped end provides support and quick height adjustment when paired with a step block.
Good for occasional machining, economy kits contain lower-strength components than standard kits.
Get everything needed for basic workholding on a machine table.
A plastic pad on the gripping surface of these clamps prevents workpiece marring, making them useful for holding polished surfaces and reducing the need for secondary finishing steps.
Unlike other setup clamps that grip the horizontal surface of a workpiece, these clamps have a pivoting ball in the tip to get a firm hold on angled parts.
Making minimal contact with the workpiece while holding securely, these clamps are good for small parts and can clamp into holes and notches.
Position these clamps between two workpieces, vises, or fixtures and secure both to your machine table using T-slot nuts or bolts.
The offset shape provides more clearance above the nut than standard clamps. Also known as gooseneck clamps.
Designed to provide more clearance above the nut than standard clamps, these have an offset shape. Also known as gooseneck clamps.
Use these clamps to hold large round parts for machining. Each clamp comes with five lengths of chain that combine to accommodate different size workpieces.
Also known as toe clamps, these grip the side of a workpiece to leave the top free for machining.
The built-in T-slot nut on these side clamps lets you clamp a part to a machine table quickly. Their small footprint leaves more free space on your table than standard side clamps.
Smaller than standard setup clamps, these clamps leave more usable space on a machine table when mounting a vise.
Attached to an arm you can flex into position, these clamps hold objects such as a flashlight, tool, or instructions.
Clamp thin materials, or use in tight spaces.
Press the lever to lock the clamp onto material.
The long, narrow jaws clamp farther into a workpiece and in tight spots.
Hold large workpieces with a standard-size clamp. Slide the jaws to adjust the opening size.
These clamps meet DIN VDE 0680-1 for protection against accidental contact with live electrical circuits.
Squeeze the handles to open the clamp; release and the spring holds it tightly in place.
Extend the handle to reach the clamp into tight spaces.
Turn the knob to adjust the opening size.
Slide the upper jaw to adjust the opening size. These clamps hold larger workpieces than other locking plier clamps of similar size.
Squeeze the handles and the jaws will automatically adjust to fit your workpiece.
The jaws on these tools apply outward pressure for use as a spreader.
Mount to the top of your workbench.
A removable, heavy duty steel base plate provides a flat, durable clamping surface. Carry it where needed or mount the base plate to your workbench.
Angled jaws clamp sheets, bars, and U-channels at 90°.
Press the lever down to lock these clamps, which fit in tight spaces and hold thin materials.
For repetitive clamping, turn the holding screw to adjust the opening size one time, and then use the handles to secure and release workpieces.
Use these tools for light duty clamping. Squeeze the handles to open; release to close.
The long, pivoting jaws let you clamp farther into your workpiece and in tight spots.
Clamp thin sheet material together without drilling holes. These clamps open with special pliers and spring closed when the pliers are released.
Set includes 12 clamps and the installation pliers required for positioning and removal.
The spring-loaded tips on these clamps swivel in all directions to make maximum contact with angled and uneven workpieces.
Combine fast-threading components to build a clamping assembly.
When loosened, you can spin the body of this clamp around its mounting point for better access to the workpiece.
Also known as press screws, mount these clamps through a drilled hole and turn the crank to move the jaw end of the screw in and out.
Fit the draw arm over a latch plate and pull the handle to clamp.
Mount the clamp on a lid and the latch plate on the side of a container.
Secure a workpiece from the inside, leaving the outside clear for machining.
These clamps wedge against the workpiece ID to grip cast, unfinished, or uneven parts, leaving the outside clear for machining.
Build these components into fixture plates, machine subplates, and tombstones for quick changes. The system clamps and locates at the same time for accurate positioning with repeatability of ±0.0005".
Mount using the holes in the base.
Machine these fixture clamps to match the contours of your workpieces for a stronger grip. Place the clamp between the two workpieces in a fixture and tighten the screw to extend the sides of the clamp, creating a secure hold against both workpieces.
Set one of these clamps between two workpieces in a fixture and tighten the screw to push the clamp's sides out for a secure hold.
Screw these clamps directly into a tapped hole in a fixture.
Tighten the spring-loaded socket head cap screw on these clamps to hold your workpiece from above.
Hold a workpiece securely from the side with minimal contact, leaving more of the workpiece free for machining.
Machine these clamps to match the contours of your workpiece and turn the screw to grip.
Unlike the smooth and flat edges of standard fixture clamps, these clamps have ridges that bite into parts, making them good for gripping castings and rough-cut stock.
Machine these fixture clamps to match the contours of your workpiece for a stronger grip.
Install these clamps into a slot in your fixture to grip at the bottom of a workpiece edge, giving the cutting tool maximum access.
Turn the handle to tighten these multipurpose tools for strong clamping in nearly any application.
With five times the capacity of standard C-clamps, these are the highest capacity clamps we offer.
These clamps have twice the capacity of standard C‐clamps.
Plastic clamping surfaces prevent damage to material.
Lighter weight than other metal clamps, these are less likely to bend thin material.
All components of these clamps are made of aluminum-bronze that is Factory Mutual approved. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.
A bright finish makes these clamps easy to see.
These clamps are made of stainless steel for excellent corrosion resistance.
Made entirely of fiberglass, these clamps won’t transmit electricity and are chemical resistant. They're often used around electrical equipment as well as in plating and anodizing applications.
Three screws apply pressure to three sides of a workpiece.
With no handle or protruding screw, these clamps can fit into tight spaces.
The clamp body is extra-slim to fit into narrow openings.
Clamp farther in from the edge of a workpiece than with other C‐clamps.
Press the quick‐release button and slide the screw into position to make adjustments in less time.
Hold the workpiece down against a bench or table.
The jaws move in unison to apply even pressure and prevent twisting.
Apply pressure to the side of a workpiece as well as the top and bottom.
For repetitive clamping, turn the holding screw to adjust the opening size one time, and then use the handle to secure and release workpieces.
Two clamps connected by a pivoting arm hold workpieces at nearly any angle.
Sized for small parts and tight spaces, these clamps have a pivoting pad at each end to hold workpieces at any angle up to 180°.
Each arm has a handle for turning the magnets on and off.
Hold and align up to three workpieces at 90° angles.
Clamp workpieces from the outside at a 90° angle, leaving the inside free for welding or fabrication.
Hold magnetic workpieces in place with these clamps.
Switch the magnets on these clamps on and off for easy placement and removal of your workpiece.
Each jaw can be positioned at an angle to hold round, angled, and odd-shaped material.
The matching jaws are ground flat for a firm grip and even pressure when clamping smooth surfaces.
Also known as J-clamps, these provide additional clearance to reach around obstructions and clamp workpieces in recessed areas.
Attach to your bar clamp to hold material on three sides.
The swivel pads pivot to grip nearly any shape of material.
Clamp much farther in from the edge of the workpiece than with standard bar clamps.
The large, flat jaws remain parallel when clamping to apply even pressure without denting or marring the workpiece. Pull the handle to lock or release the clamping arm.
Each arm slides freely for quick, one-handed positioning. They lock when the screws are tightened onto a workpiece.
Press the trigger to slide the clamping arm along the bar. Release the trigger and squeeze the pistol-grip handle to lock the clamp in place.
Hold up to five times the capacity of standard bar clamps. These are also known as I-beam clamps.
Press the trigger to slide the clamping arm along the bar. Release the trigger and squeeze the pistol‐grip handle to lock the clamp in place.
Pull the handle to lock the jaw in place and prevent loosening caused by vibration.
All adjustments can be made from one end, allowing clamping in tight spaces.
Pull the lever to slide the clamping arm along the bar; release to lock in place.
Place the arms on a pipe that is threaded at one end and at least 12" long to create your own bar clamp.
The clamping arm slides freely along the bar for quick, one handed positioning. Tighten the screw onto a workpiece and the arm locks in place.
These clamps have twice the capacity of standard fast-action bar clamps.
For the most demanding jobs, these clamps have almost five times the capacity of standard fast-action bar clamps.
An easy-to-tighten band encircles and holds round and odd-shaped objects with even pressure.
Sets include clamps with different ODs as well as installation pliers.
Insert these clamps into drilled holes in sheet material to grip and align when riveting or welding.
Quickly align, level, and join two flat surfaces. Use the suction cups to grip pieces of material and turn the handle to bring them together.
The open clamp design permits welding around almost the entire pipe circumference. A combination of chains and support bars hold a variety of pipe sizes.
Hold pipe and fittings together for tack welding.
Clamp up to three workpieces at 90° angles.
Hold workpieces at a 90° angle.
With five times the capacity of standard corner clamps, these secure two workpieces at a 90° angle.
Build a custom clamping system for holding lightweight objects such as beakers and laboratory equipment.
Secure small parts in spring clamps to keep hands free for soldering, gluing, and assembly.
Quickly install and remove the clamp-on base from a benchtop.
Use these vises for general purpose workholding.
For big jobs, these vises have a wider jaw opening, deeper throat depth, and larger footprint than standard vises.
Hold your smallest workpieces in these vises, which have a clamp-on base for quick installation and removal from a benchtop.
Hold tiny workpieces in these compact vises.
Made of 304 stainless steel to stand up to washdown environments, such as food and beverage production, these are the most corrosion-resistant vises we offer.
Designed for outdoor use, these vises have a finish that resists corrosion.
The movable jaw can be repositioned to extend the jaw opening. Pull out the entire sliding section and insert it on the opposite side of the vise.
A bright yellow vise body stands out on the shop floor.
Two vise heads tilt and rotate 360°, locking in place to hold work at any angle.
The head tilts and locks in place to hold work at an angle.
For large workpieces, these vises open three times as wide as standard tilting-head vises. Tilt and lock the head to position work at an angle.
Rotate the head 360° to use three different vise jaws and lock workpieces in position at 45° intervals.
Also known as woodworkers' vises, these mount to the underside of your workbench and sit flush with the surface.
The attaching end swivels, tilts, and locks into place to position objects. These bases are often used on workbenches and at assembly stations.
Designed for precision grinding and inspection, the construction of these vises ensures workpieces are held perfectly square. They are also known as toolmakers’ vises.
The small size allows multiple vises to be mounted on a single machine table. Frequently used in 4- and 5-axis milling machines, these vises have stepped jaws with serrated teeth that firmly grip just a small portion of your workpiece.
Use these vises for reliable workholding on CNC machines.
The vise body and stationary jaw are one piece for high repeatability, even under heavy clamping loads. Ground flat on the base and three sides, these vises ensure accuracy whether mounted on the base, either side, or upright.
Designed to hold your part on 4- and 5-axis milling machines, these vises provide rigid clamping while exposing five full sides of the workpiece. This allows even complex parts to be completed in a single operation. You must cut a dovetail into your material before the vise can grip it.
Use the adjustment dials to ensure your work is accurately positioned on X and Y axes.
The dials on these vises are graduated in smaller increments than standard cross‐slide drill‐press vises for finer adjustment. Use to precisely position work on X and Y axes.
Tilt and lock the vise to hold work at any angle up to 90°.
The base and three sides of the vise are ground flat, enabling mounting on its base, either side, or upright.
Push the handle to slide the jaw into place for quicker setup than standard drill-press vises.
Turn the handle to move the jaw on these basic vises.
Compressed air controlled by a foot pedal allows hands‐free operation. Use these vises in production applications with frequent insertion and removal of workpieces.
Tilt the head on two axes and rotate the base to position your workpiece at almost any angle.
Reliably hold workpieces with these basic machine vises.
The jaws move inward at the same time to consistently position your workpiece in the center of the vise.
Arrange the pins in a series of holes to grip parts with angled or uneven sides.
Notches on the jaws hold round material on its outside diameter.
Three chuck‐style jaws clamp around your part.
Plastic jaw inserts prevent damage to the workpiece.
Squeeze the body to open the flat jaws; release to grip.
Jaw are serrated or grooved to firmly grip workpieces.
Each end of the vise has a collet to hold a different tool—turn the collar to close the collets around them.
Press the rotating end cap on the handle with your palm to apply constant pressure while turning the body of the vise with your fingertips.
A rubber-covered body provides a comfortable grip. These vises have a rotating end cap on the handle that allows you to apply constant pressure while turning the body of the vise with your fingertips.
Clamp and unclamp with one hand by sliding the knurled ring forward to close the collet.
Sets include four vises with different opening sizes. A hollow body allows wires and rods to pass through.
Pass wires and rods through the hollow body of these vises.
Secure these heavy duty vises to the back of a truck to clamp at your job site.
Lift the end of these sine vises by placing gauge blocks underneath—they hold tools and workpieces at precise angles for grinding, cutting, and inspecting.
A wide opening, large throat depth, and grooved jaws accommodate circuit boards and other flat objects.
Set up the tripod wherever you need to work.
Keep clean rooms free of contaminants. These tripod-mounted vises have rubber-covered jaws that prevent metal-to-metal contact and a plastic-encased chain that seals in lubrication.
The jaws are rubber coated to prevent damage to pipe and other round workpieces.
Steel jaws secure round workpieces such as pipe, tubing, and conduit.
Add components such as clamps, brackets, stops, rests, mounting plates, fixturing squares, risers, and V-blocks to build fixtures for welding and assembly.
Use the rounded hook to open and close windows.