Fasten hard-to-bond plastics, such as polypropylene and polyethylene.

Form bonds in 5 seconds or less.

These adhesives withstand temperatures of 390° F or more.

Make strong, instant bonds on a variety of materials—but not your skin.

Form bonds without the strong odor of other instant-bond adhesives.

Bond plastics, porous materials, or dirty surfaces.

These super glues are blended with rubber for better impact and moisture resistance than other instant-bond adhesives.

These thin liquids, also known as super glue, flow into small gaps.

To invisibly bond transparent plastics, these adhesives won’t turn cloudy.

Moisture, humidity, and immersion in water won't degrade the bond of these adhesives.

Invisibly bond glass and transparent plastics.

Toughened adhesives are blended with rubber particles for better impact resistance than standard epoxies. They form flexible, resilient bonds.

Even when used under water, these adhesives maintain their strength.

To allow time to adjust and position parts, these epoxies remain workable for at least 90 minutes.

Fasten hard-to-bond plastics, such as polypropylene and polyethylene, with these epoxies.

These machinable epoxies are mixed with metal so they can be used to repair cracks and threaded holes.

Bond most materials without the strong odor of other epoxy adhesives.

Fasten hard-to-bond plastics, such as polypropylene and polyethylene, with these adhesives.

Toughened adhesives are blended with rubber particles for better impact resistance than standard acrylics. They form resilient bonds.

Solvents, oils, acids, and other chemicals won't degrade the bond of these adhesives.

With high shear strength and peel strength, these form the strongest bonds of our urethane adhesives.

When heated, these glue sticks melt and quickly begin to harden. Use them to seal packaging and form other low- to medium-strength bonds.

This glue remains flexible after curing to accommodate joint movement.

Also known as Gorilla Glue, this glue expands to form stronger bonds than other glue.

The 3M VHB adhesive on these rolls offers a strong hold that can replace rivets, spot welds, and other permanent fasteners.

Use these glue rolls with 3M dispensing guns.

In addition to being waterproof, this glue is made of FDA listed materials.

Bond sanding discs with a paper, cloth, or fiber backing to backup pads. This glue removes cleanly, so it's easy to change to another disc.

This putty-like glue cures into a pliable rubber. Use it to repair seals and cracks, or mold it into hooks and bumpers.

Pull off a small piece of putty and stick lightweight objects to a surface.

Form bonds with twice the strength of our other spray adhesives.

For easy positioning, this adhesive remains tacky for hours. Once items are in place, apply pressure to create a permanent bond.

Spray a coating of this glue onto one surface to temporarily hold small parts.

Bonds reach full strength in 10 minutes.

These adhesives resist temperatures up to 500° F.

Form strong bonds on most plastics.

Because this cement won't break down when exposed to corrosive waste, it's often used on plastic pipe fittings in laboratories.

Rubber cement allows repositioning until fully dried. Use it on paper and cardboard.

Install building materials such as wood and drywall with these general purpose adhesives.

Use these adhesives to bond lumber and plywood.

Bond and repair nosing and stair treads with this thick, two-part epoxy.

Adhere vinyl and rubber wall bases to wood, drywall, and concrete.

An alternative to solder, these flexible, silver-filled adhesives accommodate joint movement. Use them to bond electrical components and repair circuits.

Bond new concrete to old concrete, or use this adhesive as a primer on concrete surfaces.

These kits include adhesives, applicators, and mixer nozzles.

Use these guns to dispense two-part adhesives. Do not use them with 3M dual cartridges.

Dispense two-part adhesives with compressed air. Use these guns only with 3M dual cartridges.

Use these plungers with a 3M dispensing gun for adhesives in dual cartridges.

Adapt a standard caulk gun to dispense two-part adhesives from 1.69-oz. cartridges.

Dispense small amounts of two-part adhesives.