Also known as super glue, these adhesives bond quickly.

Accommodate joint movement with these adhesives that remain pliable when cured.

Mixed with rubber for better impact resistance than standard instant-bond adhesives, these adhesives form strong, resilient bonds.

To invisibly bond transparent plastics, these adhesives won’t turn cloudy.

Make strong, instant bonds on a variety of materials—but not your skin.

Use these thick gels, also known as super glue, on vertical surfaces or to fill gaps between parts.

These thick gels fill gaps up to 0.2" wide—the largest of any of our instant-bond adhesives.

For faster bonding, these adhesives begin to harden in half the time of our other wicking instant-bond adhesives.

These adhesives withstand temperatures up to 480° F.

For flexible bonds that resist cracking, these adhesives stay pliable.

For easy positioning, these adhesives begin to harden only when exposed to light.

For quick repairs, these epoxies begin to harden in 6 minutes or less.

Toughened adhesives are blended with rubber particles for better impact resistance than standard epoxies. They form flexible, resilient bonds.

For invisible bond lines, these adhesives dry clear.

Assortments include eight different epoxies in 0.1-oz. packets to handle a variety of small jobs.

With excellent resistance to corrosive chemicals and salt water, these epoxies work in tough conditions.

These self-extinguishing epoxies meet UL 94 V-0 for flame retardance.

With excellent shear strength, these acrylics form bonds at least 25% stronger than standard acrylic structural adhesives.

Toughened adhesives are blended with rubber particles for better impact resistance than standard acrylics. They form resilient bonds.

Acrylics bond to the widest range of materials, especially plastics, and require the least amount of surface preparation.

Urethane adhesives are the most flexible, so they bond dissimilar materials and damp vibration.

The polyurethane glue in these cartridges has nearly twice the shear strength of other hot-melt adhesives.

Glue hardens in 15 seconds or less to bond quickly.

This general purpose glue tackles a variety of repairs.

Apply this glue like tape for a no-mess alternative to liquid adhesives, hot melts, and staples. Also known as adhesive transfer tape.

This silicone glue withstands temperatures up to 500° F.

Bond both soft and hard wood.

This glue withstands limited exposure to water.

Bond sanding discs with a paper, cloth, or fiber backing to backup pads. This glue removes cleanly, so it's easy to change to another disc.

This glue withstands temperatures up to 500° F.

Spray a thin, uniform coat of adhesive on one or both surfaces, air dry, and then bring together to form strong bonds.

For easy positioning, this adhesive remains tacky for hours. Once items are in place, apply pressure to create a permanent bond.

Splice rubber O-rings and other gaskets with this chemical resistant adhesive.

Apply these adhesives on two surfaces, air dry, and then bring together to bond.

Bond porous materials with these low-odor, nonflammable adhesives.

When appearance is important, this cement dries clear and forms strong bonds on acrylic.

Create strong, leakproof joints between unthreaded pipe and fittings.

This cement has excellent temperature resistance for sealing insulation joints on ovens and furnaces.

Bond glass and stone to drywall, treated lumber, and subfloors.

Install vinyl and rubber treads on stairs with this adhesive.

Bond carpeting, vinyl tile, and other floor coverings to subfloors.

Install foam insulation, drywall, and paneling with these adhesives.

Tack wires to coil forms or secure and insulate hardware on printed circuit boards. These adhesives require an accelerator.

Permanently set threaded rods, studs, and rebar in concrete.

When concrete is saturated or submerged in water, use these adhesives to form strong bonds.

To simultaneously mix and dispense two-part adhesives, attach these mixer nozzles to a dual cartridge.

Only for use with 3M dual cartridges, these guns dispense two-part adhesives.

Use these plungers with a dispensing gun for adhesives in dual cartridges.