Lubricate standard grease fittings in hard-to-reach areas. Extensions have a quick-disconnect fitting that snaps into your dispensing tip for standard grease fittings.

Penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

Slide the metal sleeve up to the tip for rigidity. Slide it back down to expose the flexible nozzle.

Penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

With threads on both ends, these rigid nozzles connect grease guns to dispensing tips.

Sets include dispensing tips for grease fittings and bare lubrication points.

These rigid tip adapters penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

Mount holders in convenient locations to keep grease guns within reach.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Designed to lubricate linear motion components, such as slide bearings, guides, and ball screws, these guns work exclusively with THK grease cartridges and fittings.

Be sure you’re using the right grease—this gun has a clear barrel for identification at a glance.

Ensure that only food-grade grease is used in controlled areas—this gun only works with compatible food-grade grease cartridges.

Turn a small tube of grease into a dispenser.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Deliver small amounts of grease with only a light push against the lubrication point.

Use compressed air to dispense grease.

Replace the dispensing tip on your filler pump.

Turn the metering pin to adjust flow rate.

These dispensers come packed with grease, eliminating the mess of filling. Turn the dial to adjust flow rate.

Tighten the cover to dispense grease.

Lubricate single- and double-strand roller chain.

This dispenser delivers over three times more grease per stroke than our dual-output dispensers.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Move grease-dispensing guns in any direction without kinking the outlet hose.

Increase the pressure of your grease system when necessary to dispense thick grease and force grease through clogged fittings.

Clamp this applicator around control cables to lubricate them with minimal mess.

A needle dispensing tip provides fine control for lubricating small parts.

Pull the trigger on these oilers for easier one-hand operation than standard hand-held oil dispensers.

Mount these reservoirs directly to your machine, or use them with a flow-adjustment valve and brush to create a dispenser.

Mount these directly to your machine—the cup allows oil to gradually pass through to equipment, reducing time spent on manual lubrication.

A sealed design prevents contamination in dirty and dusty environments.

Lubricate strips of sheet stock, wire, or sheet stock edges. Max. width is 4".

Lubricate sheet stock up to 8" wide.

Serve multiple lubrication points from a single location.

Deliver an equal amount of oil to multiple lubrication points at once.

As chain, gears, and conveyors move, these brushes rotate to apply lubricant.

A sealed design prevents contamination in dirty and dusty environments. Install a line between the reservoir's pressure port and the lubricated equipment to balance pressure.

As chain, gears, and conveyors move, these brushes rotate to apply lubricant.

A solenoid automatically starts and stops flow to a single lubrication point to dispense lubricant while equipment is running.

Measure oil as it's dispensed.

Connect these dispensing stations to your bulk oil container to easily fill hand-held dispensers.

Driven by an air-powered pump, this dispenser comes with an adapter to mount through a bung opening on a drum.

With a maximum flow of 0.005 oz. per cycle, these pumps deliver small, precise amounts of oil. Turn the dial to set the cycle interval.

Use with manual and electric pumps to dispense different amounts of oil from multiple lubrication points.

Connect these modular pumps to a reservoir and a solenoid valve to automate the flow of oil.

Ready to connect to your air system, these complete systems include a timer and a reservoir.

Build a custom 1/2" system to deliver coolant, cutting oil, water, or air in any direction.

Use with Snap-Loc hose to assemble and disassemble components.

Swivel the ball-socket connections to position these arms and then lock them in place.

Use with Loc-Line hose to assemble and disassemble components.

Build a custom 3/4" system to deliver coolant, cutting oil, water, or air in any direction.

This hose is made of steel.

These nozzles handle coolant pressure up to 150 psi.

For use in the highest pressure coolant lines, these nozzles are rated for at least 1,000 psi.

For high-pressure coolant lines, these nozzles withstand pressure up to 500 psi.

Draw coolant from your existing tank.

Replace messy mist coolant dispensers—these convert compressed air into a stream of cold air. They can be used in applications where liquid coolant can't.

Draw coolant from your existing tank.

Assortments contain straight, 45° elbow, and 90° elbow fittings.

Keep thin grease from leaking out—the check valve on these fittings has a Buna-N seat that creates a tighter seal than check valves on other grease fittings.

Use these fittings in tight spaces where protruding fittings won't work.

Ensure a secure fit in unthreaded holes—these fittings cut threads as they’re installed. They're also known as hydraulic grease fittings.

Drive these fittings into unthreaded holes. They're also known as hydraulic grease fittings.

When the size or thread type of a fitting doesn't match an existing opening, use these adapters to make the connection.

Tap these tools once or twice with a hammer to install fittings.

Remove worn fittings and repair threaded holes.

Keep standard grease fittings free of dirt and moisture.

Install these fittings into threaded holes.

A filter/lubricator ensures efficiency and reduces wear on the pump. Often used with hydraulic oil and motor oil in addition to acidic and alkaline liquids, these pumps have a nonsparking motor for use in applications where electricity is unavailable or dangerous.

With a nozzle and hose, these pumps allow you to dispense directly into your container. They move liquid by pressurizing the drum, so they have few moving parts prone to wear and tear.

Often used with ammonia, etching and cleaning solutions, and other caustics, these pumps have a nonsparking air-powered motor for applications where electricity is unavailable or dangerous.

These pumps are rated for Zone 0 hazardous locations with flammable gases and vapors, so they can be used with liquids such as acetone, ethanol, methyl ethyl ketone, xylene, and mineral spirits.

Since these pumps move liquid by pressurizing your drum, they have few moving parts prone to wear and tear.