Cut the thin layer of rubber in the center of these grommets to create custom IDs to securely hold and protect wire, cable, and cords. Push these grommets into place. They turn rough-edged and uneven holes into smooth, insulated holes. Commonly used in metal panels, they also damp vibration. Also known as webbed grommets.

Keep grommets of various sizes on hand to solve whatever problems arise.

These grommets snap into place and have wings that expand against the sides of the hole to lock them in position. Use them to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth holes.

A slit in the side of these grommets allows you to install them around wire, cable, and cords that are already in place. They snap into the hole and their wings hold them tight. Use them to turn rough-edged and uneven holes into smooth, insulated holes.

Create a tight seal around wire, cable, and cords with these grommets to keep out dust, debris, and moisture.

Cut the center of these grommets with a utility knife to create custom IDs. The two‐piece design makes it easy to install and seal these grommets around wire, cable, and cords that are already in place. Use them to keep out dust, debris, and moisture.

Rated IP68, these grommets form liquid-tight seals around wire, cable, and cords to protect them against dust as well as submersion in a maximum of one meter of water.

Kits include grommets, a cutting punch, a cutting block, an installation punch, and a die set. Use them to create a way to run rope and cable through tarps, covers, and curtains.

The extended neck on the washer of these grommets adds reinforcement so you can use them in thicker material such as woven fabrics. Press them into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

No setting tools needed—snap the two parts together in a hole you've already cut to strengthen the hole and eliminate fraying. Use these grommets in tarps, covers, curtains, and other material.

Press these flexible grommets into holes and their tapered inner wall will expand when pipe or tubing is inserted to hold them snugly in place. They're often used for routing applications on metal, plastic, and fiberglass tanks.

Squeeze these flexible grommets to open the center flap—once wire, cable, and cords pass through, the flap closes tightly for dust and debris protection as well as a finished look. Use them to eliminate cord clutter on desktops, countertops, benchtops, and other work surfaces.

Wire, cable, and cords pass through the grommet opening while the bristles fill in the gaps to control dust and debris. Use these grommets to eliminate cord clutter on desktops, countertops, benchtops, and other work surfaces.

Sample multiple sizes and styles of rubber trim.

This trim withstands temperatures up to 450° F, which is generally twice as high as our standard rubber trim. Use it to protect the edges of panels, boards, and signs from impact. Made of rubber, it resists abrasion better than plastic trim.

This trim safeguards equipment from static electricity by diverting electrostatic charges quickly. Made of rubber, it resists abrasion better than plastic trim. Use it to protect the edges of electronics equipment and circuit boards from impact.

This trim has a metal core for added strength and stability. Made of plastic, it's also chemical resistant. Use it to protect the edges of panels, boards, signs, and mirrors from impact.

With a slippery surface, this trim minimizes friction between parts and is often used on conveyor rails, chutes, and guides. Made of plastic, it's also chemical resistant.

With a surface resistivity of 10 ⁵ ohms this trim safeguards equipment from static electricity by diverting electrostatic charges quickly. Made of plastic, it's also chemical resistant. Use it to protect the edges of of electronics equipment and circuit boards from impact.

This trim meets FMVSS-302 for Federal Motor Vehicle Safety Standards for flammability, UL 94 HB flame requirements, and NFPA (National Fire Protection Agency) standards. Made of plastic, it's also chemical resistant. Use it to protect the edges of panels, boards, and signs from impact.

This nylon-coated stainless steel trim combines strength with flexibility to hold snugly on flat, round, and irregular-shaped edges. It can also protect wire, cable, and hose.

Designed to withstand temperatures up to 800° F, this stainless steel trim is good for use with ovens, boilers, and heat shields. It combines strength with flexibility to hold snugly on flat, round, and irregular-shaped edges.

Even in the dark, this black and yellow striped trim draws attention to equipment and obstructions. Designed to cushion during impact, it protects edges on posts, shelving, and other surfaces from damage.

The stem on these bumpers compresses to fit into tight holes. Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

Able to withstand temperatures up to 300° F, these grips are also corrosion- and chemical-resistant.

Push to install these cord grips in wet environments and high-movement applications such as robotics and handheld equipment.

Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.

Vent air from your enclosure to equalize pressure and stop condensation from forming inside while securing cords in wet environments. These polyamide grips are lightweight and resist rusting.

Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends. With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life.

Made of PBT, these grips resist soaking up water in washdown and other wet environments while securing cords with an extra-strong hold.

Made of nylon with a nylon mesh extension, these grips resist most chemicals. The mesh provides a secure hold in applications where cable is pulled or in motion.

Keep cords from coming loose and seal water out of enclosures in extremely cold labs and storage areas. Thanks to their plastic bushing and rubber O-ring, these grips withstand temperatures as low as -75° F.

These grips have an extension that provides extra support for moving cable and prevents kinking for longer cable life.

With an oval bushing hole, these lightweight grips secure flat building cable, such as Romex and Festoon cable, in wet areas. All offer strain relief to extend cable life.

Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

Keep your cord at a gentle angle without sacrificing a tight hold, even in tough, wet environments.

These grips install into enclosure holes quickly to stabilize and relieve strain on cords.

Made of nylon, these grips resist chemicals.

These cord grips are lightweight yet durable.

The mesh extension provides a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

An insert clamps the cable in place to provide more strain relief than other snap-in cord grips for building cable.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

These stainless steel grips offer the most protection from wet, corrosive environments of any of our metal wet-location cord grips. They are rated IP67 for protection from temporary water submersion.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

Secure cords in wet and industrial environments with little room—these grips curve 45° to relieve bending stress.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These grips are nickel-plated brass for good corrosion resistance.

These 90° elbows meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

Peel away layers of rubber inserts to fit around cord grips, even when you don't know the exact diameter.

Attach a cord grip to cable without removing connectors and rewiring. These cord grips have a two-piece design to fit around cables with connectors.

The face of these grips is flush with the cable-entry point for a seamless appearance.

Secure multiple flat cable through one cord grip—reducing the space and number you need for a project, as well as saving time.

Connect to the end of conduit or a fitting to protect wires from abrasion when being pulled.

Preventing wear and cracks, these grommets shield the sections of your conduit that rub and bang against nearby components.

A spring extension prevents sharp bends and kinks in your cord, prolonging its life. These bushings, which are more rigid than grommets, shield cords from rubbing against the edges of holes in enclosures and panels, so they won’t wear down.

In addition to having a wider temperature range than our other vibration-damping grommets, these have excellent weather resistance.

In addition to having a wider temperature range than our other ribbed vibration-damping grommets, these have excellent weather resistance.

In addition to having a wider temperature range than our other vibration-damping bushings, these have excellent weather resistance.

In addition to having a wider temperature range than our other ribbed vibration-damping bushings, these have excellent weather resistance.

In addition to having a wider temperature range than our other vibration-damping washers, these have excellent weather resistance.