These counters have mounting holes and a base plate for securing to a wall or work surface.

For quick installation, these counters fit into standard DIN panel cutouts.

These counters have mounting holes and a base plate for securing to a wall or work surface.

Connect the lever on these counters to an object moving repetitively in a straight line, such as a punch or drill press.

The digits displayed on these counters are visible up to 100 ft. away.

The digits displayed on these counters are visible up to 100 ft. away.

Precisely count rotations by attaching these counters to clutches, couplings, rotors, or other rotating shafts.

These counters have mounting holes and a base plate for securing to a wall or work surface.

Wire these counters/ratemeters to an electrical pulse-emitting switch, sensor, or encoder to count input while tracking rates in units such as gallons per minute.

Quickly install these meters onto a DIN rail instead of on a surface or into panels.

These meters do not require voltage to register a count.

Combine a counter, feeder reel, coiler reel, and stand to create a wire, cable, and cord length measurer.

Feed wire through the wheels inside the included counter to take measurements.

Record steps or miles while you walk or run.

More customizable than standard indicators, these digital indicators have programmable features that help you adapt them to your application.

With their extra-smooth surface, these tops won’t trap dirt and oil.

A corrosion-resistant, stainless steel surface and sealed, plastic laminate bottom make these tops suitable for food service.

These tops have a grounding snap and a laminate surface that dissipates static to protect electronic components from electrostatic discharge.

Mount wood and plastic workbench tops to legs and bases.

Withstand temperatures of at least 194° F.

The enclosure meets NEMA 4X to protect these totalizers from dust, washdowns, and corrosive liquids.

With a display that can be mounted up to 1,000 feet from the body, these totalizers are often installed in hard-to-access areas and remote locations.

Measure the total flow volume of gasoline, diesel fuel, and kerosene.

More than twice as accurate as standard totalizers for fuel, these are rated for ±2% accuracy.

Often used in heating, cooking, and power-generating systems.

To protect against dust, washdowns, and corrosion, these flowmeter/totalizers have an enclosure that meets NEMA 4X.

With a display that can be placed up to 25 feet from the sensor, these flowmeter/totalizers are often used in hard-to-access areas.

Use with oil, gasoline, diesel fuel, and kerosene.

In addition to a transmitter, these kits include a 6 1/2-ft. cable and a mounting bracket.

Often used with servomotors, these transmitters have a mounting hole pattern that fits a three-hole 28 mm BC servomotor face.

These traditional dial timers count down to zero or count up to 60 minutes.

Track time on food processing lines while reducing the risk of contaminating the food. To help you comply with Hazard Analysis and Critical Control Point (HACCP) programs, these plastic stopwatches contain metal and chemical additives that will set off metal detectors and show up on X-ray machines.

Transmit pH readings to a PC for analysis. This meter has a sensor on a 3-ft. cable for taking remote readings of water and other clean liquids.

Check pH in harsh field conditions. These floating meters that have a housing that meets IP67 for complete resistance to dust and protection from temporary submersion.

Check a solution’s electrical conductivity to indicate the concentration of salts, nutrients, chemicals, and other substances.

Since this oxidation reduction potential (ORP) meter has a housing that meets IP67 for complete resistance to dust and protection from temporary submersion, it’s often used to determine a solution’s ability to break down contaminants in harsh field conditions.

Since these meters float and have a housing that meets IP67, they won’t be damaged by temporary submersion and have complete resistance to dust. They detect total dissolved solids (TDS) in water, hydroponic solutions, and other clean liquids to determine contaminant levels.

The remote probe on a 3-ft. cable limits your exposure when taking total dissolved solids (TDS) measurements to determine contaminant levels in aquaculture solutions, boiler condensate, contaminated water, and other dirty liquids.

Commonly used to test environmental samples, boiler condensate, wastewater, and other dirty liquids for contaminants, this bench-top meter determines the total dissolved solids (TDS) in a solution.

Remote sensors let you take pH and oxidation reduction potential (ORP) readings up to 3 feet from the display.

Upload up to 500 conductivity and total dissolved solids (TDS) readings to a PC. This meter has a probe on a 3-ft. cable for taking readings in hard-to-reach areas.

Record your calculations and print receipts.