This thin lubricant penetrates into tight spaces, and nano-sized additives fill small surface imperfections, reducing wear and heat and extending the life of both the lubricant and equipment.

For use in food-processing and preparation areas, these thin, multipurpose lubricants are NSF registered H1 or FDA compliant for incidental food contact.

Protect food-processing and preparation equipment while limiting environmental impact. These multipurpose lubricants are NSF registered H1 for incidental food contact and are rated to quickly break down in water.

Protect chain and other moving metal parts found in food-processing and preparation equipment while limiting environmental impact. These lubricants are NSF registered H1 for incidental food contact and break down quickly in water.

These lubricants foam when applied, so they don’t drip while sinking into roller chain and other moving metal parts. They dry to form a film that prevents dust, dirt, and corrosion.

Spray these lubricants onto wire rope and cable used in vertical or fast-moving applications. They dispense as a thick gel, completely covering wire strands without dripping or running off. Use them to cut through dirt, grease, and rust, and to protect wire rope and cable.

Protect wire rope and cable from corrosion in wet environments. These lubricants have fast-penetrating solvents that quickly reach the core of wire rope and cable to remove water and protect against corrosion.

Protect electrical components—these lubricants insulate and block moisture, preventing electrical malfunctions. They cut through dirt, grease, and rust to clean connections and relays, leaving behind a thin film for long-lasting protection.

Formulated for use on soft metal, such as aluminum, copper, and brass, these lubricants won’t stain. They reduce friction between your cutting tool and workpiece to make cutting cycles faster and easier, improve surface finishes, and extend tool life.

Reduce mess and waste with these easy-to-apply, nonstaining lubricants. They reduce friction between your cutting tool and workpiece to make cutting cycles faster and easier, improve surface finishes, and extend tool life. All resist running and dripping.

Also known as plumber's lard oil, these light-colored lubricants are chlorine and sulfur free, so they won't stain soft metal, such as aluminum or copper. They reduce friction between your cutting tool and workpiece to make cutting cycles faster and easier.

For use in food-processing and preparation areas, these lubricants are NSF registered H1 for incidental food contact. They reduce friction between your cutting tool and workpiece to make cutting cycles faster and easier, improve surface finishes, and extend tool life.

Apply these lubricants to abrasive belts and wheels to extend their life and improve ground glass surface finishes. They lubricate the abrasive surface for faster and easier cutting cycles. They won’t stain metal, so they can be used as general purpose grinding fluids.

Spray these lubricants on saw blades and drill bits to make cutting easier and extend the life of your tool. They protect tools from sap, reducing cleaning time. Made without silicone or petroleum, they won’t stain wood or interfere with glue or finishes.

These electrical discharge machining (EDM) lubricants resist oxidation, so they last longer and extend the life of your electrode. They're clear for workpiece visibility.

Designed for use with misting systems, these coolants have excellent cooling properties for intermittent machine cycles when milling and turning.

Apply just a few drops of these coolants to your cutting tools before and during milling and machining to reduce heat with very little cleanup.

For use with micro-drop dispensers, these coolants are mixed with air to create small, controlled droplets that dissipate heat and are easy to clean up. Use for small jobs.

For general-purpose grinding, sanding, and finishing, these coolants prevent material from building up to ensure a high-quality finish and preserve tool life.

Remove heat from long machining cycles with hard metal. These coolants prevent workpiece corrosion and distortion to improve cutting accuracy.

Designed to handle high pressure generated while tapping, threading, and reaming, these coolants dissipate heat and prevent corrosion to improve surface finishes and extend tool life.

Weld longer without damaging your torch—replace the water in your welding cooler with these coolants to prevent mineral deposits and frozen lines. Coolants also tolerate colder temperatures than water. For use with MIG, TIG, spot, and stud welders. They are nonconductive.

Thickened with silica, this heavy grease clings to parts so it won't wash off in wet environments.

A firm consistency and resistance to evaporation make this grease ideal for vacuum applications, such as flow meters, vacuum and pressure systems, and laboratory equipment.

This grease meets NSF/ANSI Standard 51 and FDA 21 CFR 175.300 for direct contact with food and NSF/ANSI Standard 61 for use with components that come into contact with drinking water.

This grease remains stable and in place under high pressure, heavy loads, and shock loads. It's often used for demanding mining, construction, and automotive applications.

Protect equipment while limiting environmental impact. This grease breaks down quickly in water.

Nano-sized additives penetrate small surface imperfections, reducing wear and heat to extend the life of both the lubricant and equipment. It's formulated to adhere to metal parts and to stay in place in wet environments.

Protect equipment while having a limited impact on the environment. This grease resists moisture but still breaks down quickly in water.

Brush on most metal surfaces to provide a layer of protection against corrosion.

For use in applications where acids, bases, oxidizers, and fuels are present.

This grease remains stable and in place under high pressure, heavy loads, and shock loads. It is NSF registered H1 and FDA compliant for incidental food contact. It's often used to lubricate heavy-duty food production equipment.

This grease comes in cartridges that only work with our Controlled-Use Food-Grade Lever-Grip Grease Guns to make sure that the right grease is used in food-processing areas. It is NSF registered H1 for incidental food contact.

Also known as spindle grease, use this in machine tools and other high-speed applications.

Lubricate the ball and roller bearings that support your highest loads, such as wheels and heavy equipment.

Lubricate ball and roller bearings for high-load applications in wet environments, such as water processing, steel mills, and mining.

Lubricate ball and roller bearings for high-load applications. Often used on food-processing equipment, generators, and furnace door hinges, this grease is NSF registered H1 and meets FDA Compliant 21 CFR 178.3570 for incidental food contact.

Made with moisture-resistant thickeners, this grease resists washing off and reduces corrosion in wet environments while still lubricating under heavy loads.

Made with moisture-resistant aluminum thickener, this grease resists washing off and reduces corrosion in wet environments while still lubricating under heavy loads. It is NSF registered H1 for incidental food contact.

Made with moisture-resistant thickener, this grease resists washing off and reduces corrosion and oxidation in wet environments.

A high silver content gives this grease excellent conductivity for applications where electricity and heat transfer are required.

Lubricate, clean, deoxidize, and prevent corrosion on electrical contacts to improve their performance.

Specifically designed for use with air-powered impact wrenches, this grease withstands high pressure and heavy loads and prolongs tool life.

Keep ball screws moving smoothly, even under heavy loads.

Prevent wear and corrosion to keep carriages, guide rails, slides, tracks, and ways fast and accurate.

Micro vibrations caused by surface imperfections on carriage bearings can affect precision. This grease fills in those imperfections so carriages roll smoothly.

Highly pure, this grease won't contaminate sensitive environments, so it can be used in clean rooms.

Use this oil where zinc compatibility or environmental issues are a concern.

Protect equipment while having a limited impact on the environment. This oil breaks down quickly in water.

This heavy-duty, high-pressure oil protects hydraulic jacks from corrosion and wear.

This oil withstands the heavy loads found in gear boxes.

Phosphorus additives give this oil the strength it needs for use in worm gears.

For use in worm gears, this oil stands up to high pressure. Use it in food-processing and preparation areas where incidental contact with food is possible.

This oil is chemically inert and long lasting with an indefinite shelf life.

Use this oil in food-processing and preparation areas.

Keep air-powered tools running longer. This oil prevents corrosion and has wear-resistant and extreme-pressure properties. It absorbs water to reduce condensation and prevent buildup.

Mix these treatments with gasoline or oil to improve engine performance.

Increase the pressure mineral oil can withstand in low-speed, high-pressure applications, such as gears, plain bearings, and ways.

This stabilizer contains nano-sized additives, which penetrate small surface imperfections to reduce wear and heat, extending the life of both the oil and the engine while improving performance.

Also known as flushing fluids, these additives provide wear resistance while flushing and cleaning hydraulic systems, gear boxes, compressors, and other equipment.

Designed to soak into small spaces, this thin oil keeps delicate instruments running smoothly.

Reduce wear on rings, cylinders, and other moving parts in most major manufacturers' air compressors.

Designed to flow well at extremely low temperatures, use this oil with ammonia refrigeration compressors. It won't mix with refrigerant.

With better heat and oxidation resistance than mineral oil, synthetic oil lasts longer, reducing the frequency of changes.

For use in food-processing and preparation areas, this oil is NSF registered H1 for incidental food contact.

Use these NSF registered H1 lubricants in food-processing and preparation areas with a risk of incidental food contact. They form a nonstick film that won't attract contaminants, such as flour.

Also known as antifriction coatings, these slippery coatings cure to provide permanent lubrication. They're made with moly for high-load applications, such as hinges, gears, and rods. They fill in surface imperfections for a smooth, dry finish that won’t attract dust.

Prevent packages from sticking on conveyor rails and chutes. Made with silicone, use these lubricants to create a slippery dry film that won’t attract dust where metal and non-metal surfaces meet.

Made of graphite in a thin oil, these lubricants penetrate wire rope and cable to the core. When the oil evaporates, it leaves behind a dry film of graphite that prevents wear and corrosion throughout the rope without attracting dust.

Free of metal particles, these lubricants won’t react with stainless steel. Also known as thread lubricants, antiseize lubricants prevent threaded fasteners and close-fitting parts from locking together due to corrosion, contamination, or heat.

Corrosion-resistant additives allow these lubricants to prevent parts from locking together in caustic environments, such as steel mills and power plants.

Often used with engine bolts and heavily-loaded, slow-moving gears, these lubricants are formulated with moly (molybdenum disulfide) to prevent parts from locking together under high loads and pressure.

Copper allows these lubricants to conduct electricity, while graphite gives them good chemical and corrosion resistance. Use them to prevent threaded fasteners and close-fitting parts from locking together in connections where you need to conduct electricity.

Use these lubricants to prevent threaded fasteners and close-fitting parts in food-processing and preparation areas from locking together. They're NSF registered H1 for incidental food contact.

These lubricants dry to form a thin, solvent-resistant film that won't squeeze out or attract dirt. Use them to prevent threaded fasteners and close-fitting parts from locking together.

For use in food-processing and preparation areas, these lubricants are rated for incidental food contact. Coat tight-fitting parts with them before sliding together to make assembly easier.

Made of graphite, these powders and flakes lubricate under heavy loads and high temperatures. They resist most chemicals and conduct heat and electricity. Use them dry or mix with oil and grease.

Use these lubricants to release large, intricate, or difficult-to-release parts. Also known as paintable mold-release lubricants, they don’t leave a residue, so you can paint or finish the molded part without the need to clean it. They allow you to easily remove cast parts and prevent sticking, stretching, and tearing.

Also known as paintable mold-release lubricants, these lubricants don’t leave a residue, so you can paint or finish the molded part without the need to clean it. Use them for molding and casting parts in food-processing and preparation areas, or when molding parts that will be used around food. They allow you to easily remove cast parts and prevent sticking, stretching, and tearing.

From acid to xylene, these dry and liquid chemicals are useful in a wide range of industrial applications.

A safe alternative to mercury in thermometers and thermostats, gallium transfers heat and electricity without toxic vapor that can be inhaled. Also known as Galinstan.