Made to Japanese Industrial Standards, these screws have narrower and shorter heads than standard Phillips pan head screws.

Install these metric pan head screws for a low-profile, finished look—no countersink required.

The Torx or Torx-Plus drive on these metric screws have more points of contact than other drives, allowing you to tighten them without damaging the recess.

These metric screws have a Torx drive for more points of contact than other drives, allowing you to tighten the screw without damaging the recess.

These metric alloy steel screws are nearly twice as strong as stainless steel button head screws. They have a flange that distributes pressure across a wide surface, eliminating the need for a separate washer.

These metric screws have a washer with sharp external teeth that dig into surfaces for maximum holding power and vibration resistance. Also known as Sems screws, the washer rotates freely but is permanently attached.

Nearly twice as strong as stainless steel button head screws, these metric screws are made from alloy steel. Their tamper-resistant Torx drive (also known as a pin-in Torx drive) makes them difficult to remove without special tools.

A zinc plating on these metric steel screws provides mild corrosion resistance.

These metric alloy-steel screws are twice as strong as standard steel Torx flat head screws.

These metric screws help prevent counterclockwise-moving parts from loosening. Use them for medium-strength fastening.

Choose these metric screws for high-strength fastening. Often used in high-stress applications, such as valves, pumps, motors, and automotive suspension systems, these screws are at least 25% stronger than medium-strength steel screws.

Designed for construction and exterior building applications, these metric screws are often used to join I-beams and scaffolding. Their partial threading leaves an unthreaded portion that is strong enough to stand up to the sideways forces of joints.

Made to Japanese Industrial Standards, these Class 10.9 steel screws can be used in high-stress applications, such as valves, pumps, motors, and automotive suspension systems. They are at least 25% stronger than medium-strength steel screws. The flange eliminates the need for a washer.

These metric screws are suitable for fastening most machinery and equipment. They have a serrated flange that helps prevent loosening from vibration.

These Class 8.8 steel screws are suitable for fastening most machinery and equipment. They are over 50% stronger than stainless steel thread-locking screws. For vibration resistance, they have a thread locker bonded to the threads.

Tighten these screws by turning them to the left; once fastened, they prevent counterclockwise-moving parts from loosening.

Made of alloy steel, these low-profile screws are nearly twice as strong as their stainless steel counterparts. With half the height of a standard socket head, these low-profile screws fit in tight spaces.

Serrations under the head grip the material's surface for mild vibration resistance. The flange distributes pressure across the material's surface, eliminating the need for a washer.

Drill a pilot hole, cut threads, and fasten in one motion with these metric-threaded screws. Made of steel, they’re strong and wear resistant.

Cutting their own pilot hole and threads as you fasten them into material, these metric screws have a drilling tip.

These steel screws are zinc plated to resist corrosion in wet environments.

Drive the pointed tip of these screws into soft material, such as wood and drywall. They are also known as lag bolts.

Made from alloy steel, these metric fine-thread set screws have a thin edge that digs into hard surfaces for a secure hold.

These metric alloy steel set screws dig into hard surfaces for a secure hold. They have serrations on the cup edge that grip the material surface to resist loosening.

These metric screws have a square head, so you can turn them by hand or use a wrench for more torque. Also known as half dog-point set screws, they have a protruding tip that locks within a mating hole or slot to keep parts aligned.

These metric set screws have a tip that makes good contact on flat surfaces and allows you to make frequent adjustments with minimal surface damage.

Made from alloy steel, these metric set screws have a pointed tip that wedges into the contact surface for a secure hold on soft materials such as brass.

A low-profile flat-faced ball tip allows these metric set screw to be used in low-clearance applications.

These metric set screws have a rolling ball that swivels 360° to minimize surface damage and allow for slight adjustments without loosening the screw.

These metric thumb screws have a raised head that makes them easy to grip. A black-oxide finish provides corrosion resistance in dry environments.

The metric-sized threads on these screws are the same diameter as the shoulder. Comparable in strength to Class 12.9 steel.

These metric screws have a head height that's about two-thirds the head height of a standard shoulder screw. Use them in low-clearance applications such as inside machines.

Also known as wheel and axle bolts, these metric screws have an unthreaded shoulder that acts as a shaft, so material attached to the threaded end can rotate.

Sharp teeth bite into the surface of wood, rubber belting, and other soft materials to keep the bolt from turning when tightening a nut. These bolts are commonly used in tight spaces with moving parts, such as grain elevators and other belting systems, because the smooth, low-profile head provides a flush fit when installed.

These assortments include pan head screws.

These assortments include hex head screws and hex nuts.

Set screws exert pressure at the tip to hold objects in place.

For mounting items to your machine table, these kits contain the full system of necessary components.