Made of materials that are Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Flip these wrenches over to ratchet in the opposite direction.

A lever reverses the ratchet direction.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

A lever reverses the ratchet direction.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

These wrenches are made of stainless steel for excellent corrosion resistance.

These are also known as tappet wrenches.

Sized for working on small equipment, these wrenches are 4 1/8" long with a slim head and handle.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

A ratchet mechanism in the heads lets you turn fasteners in tight spaces without removing and repositioning the wrench.

The slim heads fit into tight spaces and around thin fasteners.

When turning fasteners in small spaces, these short wrenches fit where others can't.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

Extra-long bits allow access to hard-to-reach fasteners.

Extra-long bits allow access to hard-to-reach fasteners.

These sockets are also known as pin-in-hex or pin-in-socket bits.

Pivot the head to access fasteners from an angle.

Pivot the head to access fasteners from an angle.

Turn nuts on bolts and threaded rod, which pass through these sockets.

A magnet holds the fastener securely enough to drive self-tapping screws.

Pivot the head to access fasteners from an angle.

The 12-point shape quickly positions on hex fasteners.

Use bit sockets as an alternative to a screwdriver or L-key.

For high quality at a lower price, choose these U.S.A.-made sets.

Suitable for occasional maintenance work, these sets are imported.

For high quality at a lower price, choose these U.S.A.-made sets.

Extra-long bits allow access to hard-to-reach fasteners.

Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.

Attach to your socket for a longer reach.

Keep a convenient mix of hex, Torx, Phillips, and slotted bit sockets on hand.

Convert from one square drive size to another.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

Use these sockets as an alternative to a screwdriver or L-key. They are made to withstand the high torque and force of impact tools.

Lock your socket into the extension to prevent accidental disengagement.

The hex shape grips hex fasteners and prevents rounding. These sockets are made to withstand the high torque and force of impact tools.

The angled shape lets you use your bit driver like a wrench.

Adapters are set to a specific torque and cannot be adjusted.

Attach one of these adapters to a socket to turn it with an open-end or box wrench.

Pivot the head to access fasteners from an angle.

Made of aluminum-bronze, these extensions satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

The square drive has a rounded shape that allows the extension to pivot inside the socket opening and turn it from an angle.

Push the square drive through the adapter to change size.

Change a standard wrench handle into a ratcheting wrench.

Convert from one square drive size to another.

Bend these extensions around obstructions to access hard-to-reach fasteners.

Pivot the head to access fasteners from an angle.

Prevent overtightening that can damage fasteners. These adapters spring back slightly when the set torque is reached.

Pull the collar to quickly attach and remove sockets.

Twist the grip to rapidly turn a socket before final tightening or to remove a fastener once loosened. The handle also swings like a traditional ratchet wrench.

Turn sockets in the most confined spaces.

A gasket seals in permanent lubrication and keeps out dirt, dust, and moisture.

Made of aluminum-bronze, these wrenches satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Pivot the head to access fasteners in tight spots.

Made of beryllium copper, these wrenches satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Use these wrenches for medium-volume production, general maintenance, and construction applications.

The rail is smooth plastic so the clips move more easily than on steel-rail organizers.

Hold different square drive sizes on the four clip rails stored in these trays.

The slots in these low-profile organizers are a different color than the base so it's clear when tools are missing from your bench top or drawer.

Bend or cut these organizers to fit your tool box or cabinet.

Ratchet mechanisms allow you to turn fasteners in tight spaces without removing and repositioning the tool.

The offset head gives you additional clearance to turn hard-to-reach fasteners.

The head is offset 45° to provide clearance for reaching over obstructions.

The long handle provides extra leverage—add an extension to increase it even more.

A ratchet mechanism allows you to turn fasteners in tight spaces without removing and repositioning the wrench.

The heads are offset to provide clearance for reaching over obstructions.

Turn nuts on bolts and threaded rod, which can pass through the short end of the wrench. For additional leverage, slip a bar through the short end to create a T-handle.

Turn lug bolts on car and truck wheels. These wrenches have a different socket size at each end.

Mount to walls, cabinets, and other steel surfaces.

Organize your tool drawer by positioning these low-profile rails to accommodate wrenches of any length.

The slots in these low-profile organizers are a different color than the base so it's clear when tools are missing from your bench top or drawer.

These wrenches are made of stainless steel for excellent corrosion resistance.

Sets include various sizes of wrenches that fit into slots on the circumference of collars, bearings, and other machine tool components.

Made of stainless steel, these wrenches have excellent corrosion resistance.

Hinged for adjustability, these wrenches fit a range of diameters.

Change out the pins to fit a different hole size.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.

Sets include an assortment of keys. These simple tools turn fasteners from either end and reach into tight spots.

A bright finish makes these tools stand out, so they're less likely to be misplaced. They turn fasteners from either end and reach into tight spots.

These assorted keys have a ball end that allows angled entry to turn screws in hard-to-reach areas. The bright finish makes them easy to see and less likely to be misplaced.

The ball end has a detent to grip inside the screw recess and allows angled entry to turn fasteners in hard-to-reach areas.

These assorted keys have a detent that grips inside the recess to ensure screws won’t fall off. The ball end allows angled entry to drive fasteners in hard-to-reach areas.

Sets include an assortment of stainless steel keys, which protect stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Protect your stainless steel screws by using a stainless steel L-key. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.