Sets include various sizes of quick-hold external grip pullers. Each puller has a cage around the jaws that keeps them in place for a quick job of gripping bearings and pulleys.

Remove press-fit hubs and fan blades in a variety of sizes. Sets include a hub adapter and long jaws so you can grip large components.

Move the immovable—this puller set includes a hydraulic hand pump so you can create up to 17 1/2 tons of pulling force.

Separate bearings, collars, hubs, and other shaft-mounted items so you can remove them.

Clamp these separators into the V-groove of a pulley for a secure grip.

Get a grip on objects with blind holes—these pullers have an expanding collet that secures bearings and bushings from inside.

Complete with a locking storage box, use the pullers in this set to tackle a wide variety of pulling jobs—use pullers to grip objects from the outside or the inside.

Grip objects on the outside or inside to tackle both types of pulling jobs.

A flat profile and straight jaws fit in spots where other pullers do not. These pullers come with four pairs of different-sized jaws for use in external and internal pulling jobs.

Also known as steering wheel and flywheel pullers, you can change the bolt configuration on these pullers to fit a variety of tapered hole patterns.

Use a shaft protector on the tip of your forcing screw to prevent damage from pressure applied by the puller and forcing screw.

Use adapters on the ends of forcing screws and face-grip puller legs when pulling shafts, bearing caps, and pinions.

The plastic handle provides a comfortable grip.

Lift and pry small objects, such as electronic and circuit board-mounted components. These tools are also known as chip lifters.

Sets include three pry bars with a plastic handle for a comfortable grip.

One end of these pry bars is aluminum-bronze coated to prevent scratching. Often used to separate die blocks, they're also known as die bars.

An insulated handle protects against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Knock out pins and rivets that have already been loosened. These tools are also known as pin punches.

Impact-resistant steel makes these punches stronger and more durable than standard pin-removal punches.

Made of materials that are Factory Mutual approved, these nonmagnetic, corrosion-resistant tools inhibit sparking. They satisfy OSHA requirements for nonsparking tools.

Loosen pins and rivets before removal.

A hammer and punch in one, this tool knocks out pins, rivets, and bolts.

Use these sets to knock out pins and rivets that have already been loosened.

The rounded tip of these punches fits into the open ends of hollow and spring pins to protect them from damage during removal.

Loosen pins and rivets before removal.

Squeeze the handles to install blind rivets.

Contoured handles provide comfort and a secure grip.

Swivel the head to install blind rivets at any angle.

A built-in receptacle collects spent mandrels.

Compressed air creates a vacuum that securely holds the rivet in the tool before installation and ejects the mandrel out of the tool after.

Designed for durability, these tools can handle the demands of high-volume production and assembly.

Use these tools for repair and maintenance work.

Use your drill as a blind rivet tool.

Place these extractors over stripped or deformed bolt heads that can be difficult to grip with a wrench. Tap in place with a hammer and turn to extract without damaging the threads around the fastener.

Use a square-drive ratchet wrench and socket to turn and extract fasteners.

Store your extractors and corresponding drill bits.

Keep a selection of extractors on hand to back out a variety of broken parts without damaging the threads around them.

These extractors provide the tightest fit and the most contact with the part to be removed but also cause the most expansion.

Deep flutes provide a strong grip and reduced expansion of the part you need to extract.

The extractors in these sets have a tapered wedge shape that won’t expand the broken part, making it easier to remove. After drilling, tap in with a hammer and turn.

Drill and remove broken screws, bolts, and studs with a single tool.

The tapered wedge shape of these extractors won’t expand the broken part, making it easier to remove. Sets include the matching drill bit sizes.

The short and stocky design provides a strong grip without needing to drill a deep hole. After drilling, insert the extractor and turn.

Take out socket set screws that have damaged or rounded recesses without drilling.

Extract flat-head socket cap screws that have damaged or rounded recesses without drilling.

Use these sets to extract socket head cap screws that have damaged or rounded recesses without drilling.

The extractors in these sets take out socket set screws that have damaged or rounded recesses without drilling.

The head has a serrated hammer on one side for driving staples, a point on the other for pulling staples, and a staple grip on top.

Contains pin-loosening, pin-removal, and center-marking punches as well as chisels.

Use the assorted tools in these sets to pull material out of tight spots. The corkscrew tips twist into material for a firm hold while the handle provides the necessary leverage for pulling.

Sets include an assortment of handles and tips for pulling material out of tight spots. Replace tips when they become worn or to use a different style.

The assorted tools in these sets are used to hold, separate, and position wire, springs, and other small parts.

Hold, separate, and position small parts with one tool. These sets include assorted picks with a different tip at each end.

The handles of these assorted picks have a magnet at the end to pick up small steel objects. Use to hold and position wire, springs, and other small parts.

Sets include a handle and an assortment of tips for holding and positioning wire, springs, and other small parts.

Reach around obstructions and into tight spaces with picks that have long, angled tips. Use these tools to hold, separate, and position wire, springs, and other small parts.

Solder won’t stick to these assorted picks, which are used for positioning circuit board components.

Made of beryllium copper that is FM approved, these picks satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

An insulated handle protects against accidental contact with live electrical circuits. These picks are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

The assorted picks in these sets are used to install and position tiny springs and wires. Unlike conventional picks that have pointed tips, these are rounded to prevent damage to sensitive components.

A different tip at each end installs and positions tiny springs and wires. Unlike conventional picks that have pointed tips, these are rounded to prevent damage to sensitive components.

Similar to dental instruments, these needle-sharp picks are suitable for work around delicate circuits and components.

Also known as packing irons, the offset handle allows you to install packing into hard-to-reach areas while the blunt tip prevents accidentally cutting or damaging the packing material.

Sets include an assortment of tweezers used to remove chips and other delicate components from circuit boards.

Extra-long handles enable access to hard-to-reach areas. Also known as lineman’s and combination pliers, use these tools to pull, bend, and cut wire.

Additional features, such as wire terminal crimpers, enable you to perform a variety of electrical wiring and installation work with a single tool. Also known as lineman’s pliers, use them to pull, bend, and cut wire.

Avoid the potential for an arc flash or short circuit that can occur when using conventional insulated tools with metal components. Completely metal-free, these pliers are plastic with ceramic cutting blades. They are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. Use to pull, bend, and cut wire.

Secure a lanyard to the ring on the handle to prevent dropping your pliers when working at height. Use these tools to pull, bend, and cut wire.

Choose a stainless steel tool for environments where moisture and other contaminants are present. These pliers resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool. Use them to pull, bend, and cut wire.

Use these long-handled retrievers to grab and pull objects in hard-to-reach spots.

These hoists are small enough to fit in your toolbox and can be used in tight spaces. They have a thick, rugged frame for long life, as well as enclosed gears to protect from debris and contamination for smooth operation.

Use the ratcheting lever to lift and position your load, and the brake will securely hold it in place.

Large gears allow these hoists to lift faster with each pull compared to other hoists. Good for frequent lifting operations where user fatigue is a concern.

The body spins 360° so you can operate these hoists from any direction.

These hoists have large gears to lift faster with each pull than standard trolley-mount hand chain hoists. Good for frequent lifting operations where user fatigue is a concern.

These hoists come with fibrous rope that is lighter in weight and easier to handle than chain.

These versatile pullers give you the capacity of a winch, and have a thick, rugged frame for long life. The wire rope on the pullers is stronger than rope and webbing but not as bulky as chain.

These versatile pullers are made of aluminum with stainless steel rope for corrosive environments. They give you the capacity of a winch in a portable tool. Wire rope is stronger than rope and webbing but not as bulky as chain.

These pullers have a soft, wide strap so they won't damage surfaces.

These pullers have a thick, rugged frame for long life. They have a soft, wide strap so they won't damage surfaces.

Fibrous rope is lighter and softer than wire rope and chain. Pullers provide the capacity of a winch in a versatile, portable tool.

Push down to create a vacuum and grip your items.

Slide steel plates and blocks off a stack.

With a handle and mounting hook for portability, these winches can move from job to job.

Remove the handle to wind these winches with a power drill.

One-piece gears provide more durability than the riveted gears of other hand winches. These winches move loads more gradually than standard hand winches. They take longer to wind but require less effort.

Webbing wraps neatly around the winch to prevent tangles in the line.

Tackle frequent lifting jobs with these rugged winches—their one-piece machined gears stand up to daily use.

These winches are stainless steel for corrosion resistance. Their one-piece machined gears stand up to daily use.

These winches are designed for occasional use.

These winches operate longer than standard electric winches.

These winches operate longer and require shorter breaks than standard air-powered winches.

Install these bases in different areas of your plant and slot in your hand-winch crane where needed. They can also be used to replace existing bases.