We will reply to your message within an hour.
Use where high loads and speeds are not required.
A slit running along the length of these bearings allows you to quickly slip them into a housing—no tools required.
These nylon bearings swivel inside their housing to compensate for over 20° of shaft misalignment.
Use these nylon or acetal bearings for light loads. The closed backing blocks out dust and other contaminants.
Connect these fittings to Schedule 40 plastic pipe—they are the industry standard for residential and commercial low-pressure plumbing and water supply applications. They are plastic for good corrosion resistance.
Use these plastic fittings to connect gasoline fuel lines to machines and equipment. They have excellent corrosion resistance as well as high strength and impact resistance.
Made of corrosion-resistant plastic, these fittings won’t deteriorate when used in oil applications. They have high strength and impact resistance.
These spacers have excellent wear and abrasion resistance. Exposure to moisture may cause them to expand.
Also known as saddle washers, the curved end fits against round objects such as tube and pipe.
Position components in assemblies, as well as separate or connect parts with these standoffs.
Stick these supports to surfaces where you don't want to drill a hole. The snap-in end can be released for repairs and upgrades.
Designed for multi-level printed circuit board applications, these self-aligning, through-hole supports have a chamfered female end for stacking. The other end snaps and locks in place for a permanent connection.
Secure the self-tapping female connection with a screw; the other end snaps snugly into a panel, yet can be released for repairs and upgrades.
Wings add tension to strengthen the hold in a hole. The other end is releasable for repairs and upgrades.
Thread the male connection into a tapped hole and snap the other end into a panel for a secure hold that can be released for repairs and upgrades.
The flat top supports boards without drilling a hole while wings on the other end add tension for a secure hold in a hole.
Both ends snap and lock in place for a permanent connection.
In enclosures and other places where you don’t want to drill a hole, mount circuit boards and other thin panels with these supports.
Also known as shoulder washers.
As you tighten your screw, the rolled collar compresses under the head to create an insulating barrier between a screw shank and a mating surface.
These washers have a flat bottom and high walls to protect metal screw heads from electrical current.
Press these inserts into a drilled hole and the flexible metal teeth anchor them in the material. Use them with carbon fiber, fiberglass, and garolite.
Also known as shoulder and insulator washers, these nonmetal washers block electrical current and prevent corrosion from mating different types of metal.
These grommets snap into place and have wings that expand against the sides of the hole to lock them in position. Use them to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth holes.
The center hole has flaps that flex to hold and protect various sizes of wire, cable, and cords while keeping out dust and debris. Snap these grommets into place and their wings expand against the sides of the hole to lock them in position. Use them to turn rough-edged and uneven holes into smooth holes.
A slit in the side of these grommets allows you to install them around wire, cable, and cords that are already in place. They snap into the hole and their wings hold them tight. Use them to turn rough-edged and uneven holes into smooth, insulated holes.
Support shafts, bearings, and other moving parts that are routed through a hole. These grommets are slippery to allow parts to move freely in the hole. Install them on thin sheet-metal panels.
Made of chemical-resistant nylon, these collars are suitable for washdown applications.
Suitable for use in washdown applications, these plastic collars also offer good chemical resistance.
Each hub includes a set screw, which bites into your shaft to hold the coupling in place.
Preventing wear and cracks, these grommets shield the sections of your conduit that rub and bang against nearby components.
These grips are sized to fit in tight areas.
Snap these cord grips into place to secure cable in wet environments.
Push to install these cord grips in wet environments and high-movement applications such as robotics and handheld equipment.
Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.
A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable.
Vent air from your enclosure to equalize pressure and stop condensation from forming inside while securing cords in wet environments. These polyamide grips are lightweight and resist rusting.
Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends. With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life.
Tighten the screw-down clamp for superior pull-out resistance.
Made of nylon with a nylon mesh extension, these grips resist most chemicals. The mesh provides a secure hold in applications where cable is pulled or in motion.
These grips are made of nylon, which resists most chemicals. The nylon mesh extension provides a secure hold when the cable is pulled or in motion.
These grips install into enclosure holes quickly to stabilize and relieve strain on cords.
Built with snap-in tabs and a spring extension, these cord grips install into panel holes more quickly than standard grips and better prevent damage from sharp bends.
Made of nylon, these grips resist chemicals.
Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.
Also known as cable-entry seals, the cable-entry side has heat-shrinkable polyolefin with an adhesive lining.
The face of these grips is flush with the cable-entry point for a seamless appearance.
These grips have a thin, flexible seal that covers the holes until you push cords through.
Attach a cord grip to cable without removing connectors and rewiring. These cord grips have a two-piece design to fit around cables with connectors.
Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection.
The cable-entry side has heat-shrinkable polyolefin with an adhesive lining. These are also known as cable-entry seals.
The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.
Peel away layers of rubber inserts to fit around cord grips, even when you don't know the exact diameter.
More rigid than grommets, these bushings guard cords from rubbing against the edges of holes in enclosures and panels and wearing down.
A spring extension prevents sharp bends and kinks in your cord, prolonging its life. These bushings, which are more rigid than grommets, shield cords from rubbing against the edges of holes in enclosures and panels, so they won’t wear down.
These nylon swivel joints are 80% lighter than steel swivel joints with better corrosion resistance.
The addition of MDS gives these tubes exceptional wear resistance along with a self-lubricating surface. They're made of cast nylon 6, making them easier to machine and better electrical insulators than other MDS-filled nylon tubes.
A good choice for making sprockets and pulleys, these cast nylon 6 tubes withstand higher temperatures and are easier to machine than standard nylon 6/6 tubes.
Clip these suppressors—also known as ferrite beads and ferrite chokes—around data, USB, video, and sensitive-equipment cable to curb electromagnetic and radio frequency interference.