Search Results
For Shaft Diameter For Shaft Diameter |
|---|
For Load Direction For Load Direction |
|---|
 | Thrust |
 | Combined Radial and Thrust |
 | Combined Radial, Thrust, and Moment |
OD OD |
|---|
ID ID |
|---|
|
Thickness Thickness |
|---|
Width Width |
|---|
For Housing ID For Housing ID |
|---|
|
Dynamic Thrust Load Capacity Dynamic ThrustLoad Capacity |
|---|
|
Maximum Speed Maximum Speed |
|---|
|
Static Thrust Load Capacity Static Thrust Load Capacity |
|---|
|
Trade Number Trade Number |
|---|
|
Dynamic Radial Load Capacity Dynamic RadialLoad Capacity |
|---|
|
For Shaft Surface Smoothness (Ra) For Shaft SurfaceSmoothness (Ra) |
|---|
|
Static Radial Load Capacity Static Radial Load Capacity |
|---|
|
Construction Construction |
|---|
|
Cage Width Cage Width |
|---|
About Ball and Roller Bearings
More
Needle-Roller Thrust Bearings
Washer
Bearing
Thinner rollers allow these bearings to fit in tighter spaces than tapered-roller thrust bearings. Because of the large contact area between the rollers and washers (not included), these bearings are great for medium to heavy duty, low-friction jobs. For use on hardened and ground surfaces.
Washers allow you to use the bearing on unhardened and unground surfaces.
For technical drawings and 3-D models, click on a part number.
Bearings with Steel Rollers | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Thrust Load Cap., lbs. | 0.032" Thick Washers | 0.126" Thick Washers | ||||||||||||
| For Shaft Dia. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microns | Temp. Range, °F | Each | Each | Each | |||
Open | ||||||||||||||
| 1/4" | 11/16" | 5/64" | 1,350 | 3,000 | 20,000 | Required | 16 | 0° to 240° | 0000000 | 00000 | 00000000 | 00000 | 000000 | 00 |
| 5/16" | 3/4" | 5/64" | 1,150 | 2,950 | 24,000 | Required | 0.2 | 0° to 240° | 0000000 | 0000 | 00000000 | 0000 | 000000 | 00 |
| 3/8" | 13/16" | 5/64" | 1,600 | 4,000 | 16,000 | Required | 16 | 0° to 240° | 0000000 | 0000 | 00000000 | 0000 | 000000 | 00 |
| 1/2" | 15/16" | 5/64" | 1,900 | 5,300 | 13,000 | Required | 16 | 0° to 240° | 0000000 | 0000 | 0000000 | 0000 | 000000 | 00 |
| 5/8" | 1 1/8" | 5/64" | 2,150 | 6,600 | 11,000 | Required | 16 | 0° to 240° | 0000000 | 0000 | 0000000 | 0000 | 000000 | 00 |
| 3/4" | 1 1/4" | 5/64" | 2,400 | 8,000 | 9,500 | Required | 16 | 0° to 240° | 0000000 | 0000 | 0000000 | 0000 | 0000000 | 00000 |
| 7/8" | 1 7/16" | 5/64" | 2,900 | 10,500 | 8,000 | Required | 16 | 0° to 240° | 0000000 | 0000 | 0000000 | 0000 | 0000000 | 0000 |
| 7/8" | 1 11/16" | 5/64" | 4,400 | 18,600 | 7,500 | Required | 16 | 0° to 240° | 0000000 | 0000 | 0000000 | 0000 | 0000000 | 0000 |
| 1" | 1 9/16" | 5/64" | 3,150 | 12,100 | 7,500 | Required | 16 | 0° to 240° | 0000000 | 0000 | 0000000 | 0000 | 0000000 | 0000 |
| 1 1/8" | 1 3/4" | 5/64" | 3,850 | 16,400 | 6,500 | Required | 16 | 0° to 240° | 0000000 | 0000 | 0000000 | 0000 | 0000000 | 0000 |
| 1 1/4" | 1 15/16" | 5/64" | 4,500 | 20,500 | 6,000 | Required | 16 | 0° to 240° | 0000000 | 0000 | 0000000 | 0000 | 0000000 | 0000 |
| 1 3/8" | 2 1/16" | 5/64" | 4,600 | 21,600 | 5,500 | Required | 16 | 0° to 240° | 0000000 | 0000 | 0000000 | 0000 | 0000000 | 00000 |
| 1 1/2" | 2 3/16" | 5/64" | 4,850 | 23,800 | 5,000 | Required | 16 | 0° to 240° | 0000000 | 0000 | 0000000 | 0000 | 0000000 | 0000 |
| 1 3/4" | 2 1/2" | 5/64" | 5,600 | 30,100 | 4,400 | Required | 16 | 0° to 240° | 0000000 | 0000 | 0000000 | 0000 | 000000 | 00 |
| 2" | 2 3/4" | 5/64" | 5,800 | 32,600 | 4,000 | Required | 16 | 0° to 240° | 0000000 | 0000 | 0000000 | 0000 | 0000000 | 00000 |
| 2 1/4" | 3" | 5/64" | 5,550 | 32,000 | 5,600 | Required | 0.2 | 0° to 240° | 0000000 | 00000 | 00000000 | 0000 | 00000000 | 0000 |
| 2 1/2" | 3 1/4" | 5/64" | 6,200 | 37,500 | 3,300 | Required | 16 | 0° to 240° | 0000000 | 00000 | 00000000 | 0000 | 000000 | 00 |
| 3" | 3 3/4" | 5/64" | 6,600 | 42,500 | 2,800 | Required | 16 | 0° to 240° | 0000000 | 00000 | 00000000 | 00000 | 00000000 | 00000 |
Bearings with Steel Rollers | |||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Thrust Load Cap., lbs. | 1 mm Thick Washers | Additional Washers | |||||||||||||||
| For Shaft Dia., mm | OD, mm | Thick., mm | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microns | Temp. Range, °F | Specifications Met | Each | Thick., mm | Each | Thick., mm | Each | |||
Open | |||||||||||||||||
| 4 | 14 | 2 | 1,000 | 1,800 | 21,000 | Required | 16 | 0° to 240° | DIN 5405-2 | 000000 | 00000 | 1 | 00000000 | 00000 | __ | 000000 | 00 |
| 5 | 15 | 2 | 1,050 | 2,050 | 21,000 | Required | 16 | 0° to 240° | DIN 5405-2 | 000000 | 0000 | 1 | 00000000 | 0000 | __ | 000000 | 00 |
| 6 | 19 | 2 | 1,500 | 3,500 | 19,000 | Required | 16 | 0° to 240° | DIN 5405-2 | 0000000 | 0000 | 1 | 00000000 | 0000 | 2.75 | 00000000 | 000000 |
| 8 | 21 | 2 | 1,750 | 4,350 | 18,000 | Required | 16 | 0° to 240° | DIN 5405-2 | 000000 | 0000 | 1 | 00000000 | 0000 | 2.75 | 00000000 | 0000 |
| 10 | 24 | 2 | 2,050 | 5,700 | 17,000 | Required | 16 | 0° to 240° | DIN 5405-2 | 0000000 | 0000 | 1 | 0000000 | 0000 | 2.75 | 0000000 | 0000 |
| 12 | 26 | 2 | 2,200 | 6,500 | 15,000 | Required | 16 | 0° to 240° | DIN 5405-2 | 0000000 | 0000 | 1 | 0000000 | 0000 | 2.75 | 0000000 | 0000 |
| 15 | 28 | 2 | 2,550 | 8,050 | 13,000 | Required | 16 | 0° to 240° | DIN 5405-2 | 0000000 | 0000 | 1 | 0000000 | 0000 | 2.75 | 0000000 | 0000 |
| 17 | 30 | 2 | 2,700 | 8,850 | 12,000 | Required | 16 | 0° to 240° | DIN 5405-2 | 0000000 | 0000 | 1 | 0000000 | 0000 | 2.75 | 0000000 | 00000 |
| 20 | 35 | 2 | 2,950 | 10,450 | 10,000 | Required | 16 | 0° to 240° | DIN 5405-2 | 0000000 | 0000 | 1 | 0000000 | 0000 | 2.75 | 0000000 | 00000 |
| 25 | 42 | 2 | 3,300 | 13,000 | 8,500 | Required | 16 | 0° to 240° | DIN 5405-2 | 0000000 | 0000 | 1 | 0000000 | 0000 | 3 | 0000000 | 00000 |
| 30 | 47 | 2 | 3,650 | 15,700 | 7,500 | Required | 16 | 0° to 240° | DIN 5405-2 | 0000000 | 0000 | 1 | 0000000 | 0000 | 3 | 0000000 | 00000 |
| 35 | 52 | 2 | 4,000 | 18,200 | 6,500 | Required | 16 | 0° to 240° | DIN 5405-2 | 0000000 | 0000 | 1 | 0000000 | 0000 | 3.5 | 0000000 | 00000 |
| 40 | 60 | 3 | 6,300 | 25,500 | 6,000 | Required | 16 | 0° to 240° | DIN 5405-2 | 000000 | 00000 | 1 | 00000000 | 0000 | 3.5 | 00000000 | 00000 |
| 45 | 65 | 3 | 6,700 | 28,700 | 5,000 | Required | 16 | 0° to 240° | DIN 5405-2 | 0000000 | 00000 | 1 | 0000000 | 0000 | 4 | 0000000 | 00000 |
| 50 | 70 | 3 | 7,200 | 32,100 | 4,800 | Required | 16 | 0° to 240° | DIN 5405-2 | 0000000 | 00000 | 1 | 0000000 | 0000 | 4 | 0000000 | 00000 |
| 55 | 78 | 3 | 8,500 | 41,800 | 4,300 | Required | 16 | 0° to 240° | DIN 5405-2 | 0000000 | 00000 | 1 | 0000000 | 0000 | 5 | 0000000 | 00000 |
| 60 | 85 | 3 | 10,000 | 53,000 | 4,000 | Required | 16 | 0° to 240° | DIN 5405-2 | 000000 | 00000 | 1 | 00000000 | 0000 | 4.75 | 00000000 | 00000 |
| 65 | 90 | 3 | 10,400 | 57,000 | 3,700 | Required | 16 | 0° to 240° | DIN 5405-2 | 0000000 | 00000 | 1 | 00000000 | 0000 | 5.25 | 00000000 | 00000 |
| 70 | 95 | 4 | 12,100 | 57,000 | 3,500 | Required | 16 | 0° to 240° | DIN 5405-2 | 000000 | 00000 | 1 | 00000000 | 0000 | 5.25 | 00000000 | 00000 |
| 75 | 100 | 4 | 12,400 | 60,000 | 3,300 | Required | 16 | 0° to 240° | DIN 5405-2 | 000000 | 00000 | 1 | 00000000 | 00000 | 5.75 | 00000000 | 00000 |
| 80 | 105 | 4 | 12,500 | 63,000 | 3,100 | Required | 16 | 0° to 240° | DIN 5405-2 | 000000 | 00000 | 1 | 00000000 | 00000 | 5.75 | 00000000 | 00000 |
Washers for Needle-Roller Thrust Bearings
Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.
For technical drawings and 3-D models, click on a part number.
| For Shaft Dia. | OD | Thick. | Washer Material | Specifications Met | Each | |
| 1/4" | 11/16" | 0.032" | Steel | __ | 00000000 | 00000 |
| 5/16" | 3/4" | 0.032" | Steel | __ | 00000000 | 0000 |
| 3/8" | 13/16" | 0.032" | Steel | __ | 00000000 | 0000 |
| 1/2" | 15/16" | 0.032" | Steel | __ | 0000000 | 0000 |
| 5/8" | 1 1/8" | 0.032" | Steel | __ | 0000000 | 0000 |
| 3/4" | 1 1/4" | 0.032" | Steel | __ | 0000000 | 0000 |
| 3/4" | 1 1/4" | 0.126" | Steel | __ | 0000000 | 0000 |
| 7/8" | 1 7/16" | 0.032" | Steel | __ | 0000000 | 0000 |
| 7/8" | 1 7/16" | 0.126" | Steel | __ | 0000000 | 0000 |
| 7/8" | 1 11/16" | 0.032" | Steel | __ | 0000000 | 0000 |
| 7/8" | 1 11/16" | 0.126" | Steel | __ | 0000000 | 0000 |
| 1" | 1 9/16" | 0.032" | Steel | __ | 0000000 | 0000 |
| 1" | 1 9/16" | 0.126" | Steel | __ | 0000000 | 0000 |
| 1 1/8" | 1 3/4" | 0.032" | Steel | __ | 0000000 | 0000 |
| 1 1/8" | 1 3/4" | 0.126" | Steel | __ | 0000000 | 0000 |
| 1 1/4" | 1 15/16" | 0.032" | Steel | __ | 0000000 | 0000 |
| 1 1/4" | 1 15/16" | 0.126" | Steel | __ | 0000000 | 0000 |
| 1 3/8" | 2 1/16" | 0.032" | Steel | __ | 0000000 | 0000 |
| 1 3/8" | 2 1/16" | 0.126" | Steel | __ | 0000000 | 00000 |
| 1 1/2" | 2 3/16" | 0.032" | Steel | __ | 0000000 | 0000 |
| 1 1/2" | 2 3/16" | 0.126" | Steel | __ | 0000000 | 0000 |
| 1 3/4" | 2 1/2" | 0.032" | Steel | __ | 0000000 | 0000 |
| 2" | 2 3/4" | 0.032" | Steel | __ | 0000000 | 0000 |
| 2" | 2 3/4" | 0.126" | Steel | __ | 0000000 | 00000 |
| 2 1/4" | 3" | 0.032" | Steel | __ | 00000000 | 0000 |
| 2 1/4" | 3" | 0.126" | Steel | __ | 00000000 | 0000 |
| 2 1/2" | 3 1/4" | 0.032" | Steel | __ | 00000000 | 0000 |
| 3" | 3 3/4" | 0.032" | Steel | __ | 00000000 | 00000 |
| 3" | 3 3/4" | 0.126" | Steel | __ | 00000000 | 00000 |
| 4mm | 14mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 0000 |
| 5mm | 15mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 0000 |
| 6mm | 19mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 0000 |
| 6mm | 19mm | 2.75mm | Steel | __ | 00000000 | 00000 |
| 8mm | 21mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 0000 |
| 8mm | 21mm | 2.75mm | Steel | __ | 00000000 | 0000 |
| 10mm | 24mm | 1mm | Steel | DIN 5405-3, ISO 303 | 0000000 | 0000 |
| 10mm | 24mm | 2.75mm | Steel | __ | 0000000 | 0000 |
| 12mm | 26mm | 1mm | Steel | DIN 5405-3, ISO 303 | 0000000 | 0000 |
| 12mm | 26mm | 2.75mm | Steel | __ | 0000000 | 0000 |
| 15mm | 28mm | 1mm | Steel | DIN 5405-3, ISO 303 | 0000000 | 0000 |
| 15mm | 28mm | 2.75mm | Steel | __ | 0000000 | 0000 |
| 17mm | 30mm | 1mm | Steel | DIN 5405-3, ISO 303 | 0000000 | 0000 |
| 17mm | 30mm | 2.75mm | Steel | __ | 0000000 | 00000 |
| 20mm | 35mm | 1mm | Steel | DIN 5405-3, ISO 303 | 0000000 | 0000 |
| 20mm | 35mm | 2.75mm | Steel | __ | 0000000 | 00000 |
| 25mm | 42mm | 1mm | Steel | DIN 5405-3, ISO 303 | 0000000 | 0000 |
| 25mm | 42mm | 3mm | Steel | __ | 0000000 | 00000 |
| 30mm | 47mm | 1mm | Steel | DIN 5405-3, ISO 303 | 0000000 | 0000 |
| 30mm | 47mm | 3mm | Steel | __ | 0000000 | 00000 |
| 35mm | 52mm | 1mm | Steel | DIN 5405-3, ISO 303 | 0000000 | 0000 |
| 35mm | 52mm | 3.5mm | Steel | __ | 0000000 | 00000 |
| 40mm | 60mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 0000 |
| 40mm | 60mm | 3.5mm | Steel | __ | 00000000 | 00000 |
| 45mm | 65mm | 1mm | Steel | DIN 5405-3, ISO 303 | 0000000 | 0000 |
| 45mm | 65mm | 4mm | Steel | __ | 0000000 | 00000 |
| 50mm | 70mm | 1mm | Steel | DIN 5405-3, ISO 303 | 0000000 | 0000 |
| 50mm | 70mm | 4mm | Steel | __ | 0000000 | 00000 |
| 55mm | 78mm | 1mm | Steel | DIN 5405-3, ISO 303 | 0000000 | 0000 |
| 55mm | 78mm | 5mm | Steel | __ | 0000000 | 00000 |
| 60mm | 85mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 0000 |
| 60mm | 85mm | 4.75mm | Steel | __ | 00000000 | 00000 |
| 65mm | 90mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 0000 |
| 65mm | 90mm | 5.25mm | Steel | __ | 00000000 | 00000 |
| 70mm | 95mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 0000 |
| 70mm | 95mm | 5.25mm | Steel | __ | 00000000 | 00000 |
| 75mm | 100mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 00000 |
| 75mm | 100mm | 5.75mm | Steel | __ | 00000000 | 00000 |
| 80mm | 105mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 00000 |
| 80mm | 105mm | 5.75mm | Steel | __ | 00000000 | 00000 |
Tapered-Roller Thrust Bearings
Open
Thick, tapered rollers stand up to extremely high thrust loads.
Open bearings dissipate heat more efficiently than sealed bearings.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Each | |
Open | ||||||||||
| 1 1/4" | 2.198" | 0.625" | Steel | 12,000 | 34,100 | 10 | Required | 0° to 150° | 00000000 | 000000 |
| 1 1/4" | 2.635" | 0.7658" | Steel | 18,300 | 55,500 | 10 | Required | 0° to 150° | 00000000 | 00000 |
| 1 3/8" | 2.323" | 0.656" | Steel | 14,500 | 42,000 | 10 | Required | 0° to 150° | 00000000 | 00000 |
| 1 1/2" | 2.604" | 0.765" | Steel | 20,300 | 58,000 | 10 | Required | 0° to 150° | 00000000 | 00000 |
| 1 5/8" | 2.869" | 0.8438" | Steel | 20,500 | 62,500 | 10 | Required | 0° to 150° | 00000000 | 00000 |
| 1 13/16" | 3.276" | 0.9375" | Steel | 28,400 | 91,250 | 10 | Required | 0° to 150° | 00000000 | 00000 |
| 2" | 2.948" | 0.625" | Steel | 13,300 | 28,700 | 10 | Required | 0° to 150° | 00000000 | 00000 |
| 2 1/16" | 3.682" | 1.062" | Steel | 37,500 | 115,000 | 10 | Required | 0° to 150° | 00000000 | 00000 |
Tapered-Roller Bearings
Found anywhere from machine tool spindles to conveyor rollers, these bearings have a two-piece design that allows for adjustment.
Zinc-coated steel bearings provide better corrosion resistance than steel bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | Thrust Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | For Housing ID | Wd. | Trade No. | Outer Ring Trade No. | Dynamic | Static | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Each | |
Steel Ring | |||||||||||||
Open | |||||||||||||
| 3/8" | 1 17/64" | 5/16" | A2037 | A2126 | 630 | 2,050 | 430 | 2,450 | 7,200 | Required | -60° to 200° | 00000000 | 0000000 |
| 1/2" | 1 3/8" | 0.344" | A4050 | A4138 | 700 | 2,550 | 550 | 3,400 | 6,300 | Required | -60° to 200° | 00000000 | 00000 |
| 5/8" | 1 11/16" | 3/8" | 11590 | 11520 | 1,000 | 3,900 | 1,200 | 8,000 | 5,000 | Required | -60° to 200° | 0000000 | 00000 |
| 11/16" | 1 37/64" | 0.42" | LM11749 | LM11710 | 1,300 | 5,250 | 650 | 4,350 | 5,500 | Required | -60° to 200° | 0000000 | 00000 |
| 3/4" | 1 25/32" | 0.475" | LM11949 | LM11910 | 1,750 | 7,200 | 910 | 6,300 | 4,900 | Required | -60° to 200° | 0000000 | 00000 |
| 3/4" | 1 15/16" | 9/16" | 09067 | 09195 | 2,300 | 9,100 | 1,050 | 7,050 | 4,900 | Required | -60° to 200° | 0000000 | 00000 |
| 55/64" | 1 25/32" | 0.475" | LM12749 | LM12710 | 1,750 | 7,900 | 920 | 7,050 | 4,500 | Required | -60° to 200° | 0000000 | 00000 |
| 7/8" | 2 3/64" | 1/2" | 07087 | 07204 | 1,700 | 6,650 | 1,150 | 7,750 | 4,100 | Required | -60° to 200° | 00000000 | 00000 |
| 63/64" | 1 31/32" | 3/8" | 07097 | 07196 | 1,550 | 6,650 | 1,050 | 7,750 | 4,100 | Required | -60° to 200° | 0000000 | 00000 |
| 1" | 1 31/32" | 3/8" | 07100 | 07196 | 1,550 | 6,650 | 1,050 | 7,750 | 4,100 | Required | -60° to 200° | 0000000 | 00000 |
| 1" | 1 63/64" | 0.42" | L44643 | L44610 | 1,600 | 7,400 | 1,000 | 8,050 | 3,900 | Required | -60° to 200° | 0000000 | 00000 |
| 1" | 2 7/16" | 9/16" | 15100 | 15245 | 2,700 | 12,100 | 1,600 | 12,400 | 3,300 | Required | -60° to 200° | 0000000 | 00000 |
| 1 1/16" | 1 63/64" | 0.42" | L44649 | L44610 | 1,600 | 7,400 | 1,000 | 8,050 | 3,900 | Required | -60° to 200° | 0000000 | 00000 |
| 1 1/8" | 2 29/64" | 9/16" | 15113 | 15245 | 2,700 | 12,100 | 1,600 | 12,400 | 3,300 | Required | -60° to 200° | 0000000 | 00000 |
| 1 3/16" | 2 7/16" | 5/8" | 15118 | 15244 | 2,700 | 12,100 | 1,600 | 12,400 | 3,300 | Required | -60° to 200° | 0000000 | 00000 |
| 1 1/4" | 2 21/64" | 0.465" | LM67048 | LM67010 | 2,100 | 10,000 | 1,500 | 12,000 | 3,400 | Required | -60° to 200° | 0000000 | 00000 |
| 1 1/4" | 2 23/32" | 5/8" | 14125A | 14276 | 2,950 | 13,900 | 1,900 | 15,400 | 3,000 | Required | -60° to 200° | 0000000 | 00000 |
| 1 5/16" | 2 11/16" | 11/16" | M88048 | M88010 | 3,450 | 17,400 | 3,250 | 27,700 | 3,000 | Required | -60° to 200° | 0000000 | 00000 |
| 1 3/8" | 2 23/32" | 0.702" | 14137A | 14274 | 3,150 | 13,900 | 2,050 | 15,400 | 3,000 | Required | -60° to 200° | 00000000 | 00000 |
| 1 7/16" | 3" | 15/16" | 31597 | 31521 | 5,500 | 24,100 | 3,800 | 28,200 | 2,800 | Required | -60° to 200° | 00000000 | 00000 |
| 1 1/2" | 3" | 3/4" | 2788 | 2720 | 4,650 | 23,000 | 2,400 | 20,300 | 2,800 | Required | -60° to 200° | 0000000 | 00000 |
| 1 3/4" | 3 17/64" | 3/4" | 25580 | 25520 | 4,850 | 24,900 | 2,800 | 24,200 | 2,400 | Required | -60° to 200° | 0000000 | 00000 |
| 2" | 3 1/4" | 0.65" | LM104949 | LM104911 | 4,350 | 23,400 | 2,250 | 20,800 | 2,300 | Required | -60° to 200° | 0000000 | 00000 |
| 2" | 3 1/2" | 0.65" | 368A | 362A | 4,600 | 21,500 | 2,500 | 20,100 | 2,300 | Required | -60° to 200° | 0000000 | 00000 |
| 2" | 4 1/8" | 15/16" | 45284 | 45220 | 8,250 | 42,600 | 4,700 | 41,300 | 1,900 | Required | -60° to 200° | 0000000 | 00000 |
| 2 1/4" | 3 13/16" | 5/8" | 387A | 382A | 4,900 | 24,100 | 2,950 | 24,900 | 2,000 | Required | -60° to 200° | 0000000 | 00000 |
| 2 1/2" | 4 1/4" | 3/4" | 29585 | 29520 | 7,600 | 36,300 | 5,950 | 48,400 | 1,700 | Required | -60° to 200° | 00000000 | 000000 |
| 2 3/4" | 4 7/16" | 3/4" | 29675 | 29620 | 5,950 | 37,200 | 4,950 | 52,800 | 1,600 | Required | -60° to 200° | 0000000 | 000000 |
| 3" | 5" | 7/8" | 42687 | 42620 | 8,650 | 49,800 | 6,200 | 60,800 | 1,500 | Required | -60° to 200° | 0000000 | 000000 |
| 3 1/4" | 5 1/4" | 1.031" | 47686 | 47620 | 9,750 | 58,750 | 6,750 | 69,250 | 1,400 | Required | -60° to 200° | 0000000 | 000000 |
| 4" | 6 3/16" | 1.031" | 52400 | 52618 | 13,000 | 77,000 | 10,600 | 107,000 | 1,100 | Required | -60° to 200° | 00000000 | 000000 |
| 15mm | 42mm | 11mm | 30302 | __ | 1,400 | 4,950 | 680 | 4,100 | 5,700 | Required | -60° to 200° | 0000000 | 00000 |
| 17mm | 40mm | 11mm | 30203 | __ | 1,150 | 4,450 | 680 | 4,450 | 5,400 | Required | -60° to 200° | 0000000 | 00000 |
| 20mm | 47mm | 12mm | 30204M | __ | 1,750 | 7,400 | 1,050 | 7,450 | 4,600 | Required | -60° to 200° | 0000000 | 00000 |
| 20mm | 52mm | 13mm | 30304 | __ | 2,050 | 7,750 | 1,050 | 6,750 | 4,500 | Required | -60° to 200° | 0000000 | 00000 |
| 25mm | 52mm | 13mm | 30205M | __ | 1,800 | 8,600 | 1,150 | 9,400 | 4,100 | Required | -60° to 200° | 0000000 | 00000 |
| 30mm | 55mm | 13mm | 32006X | __ | 2,100 | 10,200 | 1,550 | 12,800 | 3,500 | Required | -60° to 200° | 0000000 | 00000 |
| 30mm | 62mm | 14mm | 30206M | __ | 2,350 | 9,850 | 1,500 | 12,700 | 3,400 | Required | -60° to 200° | 0000000 | 00000 |
| 35mm | 62mm | 14mm | 32007X | __ | 2,550 | 12,900 | 2,000 | 17,100 | 3,000 | Required | -60° to 200° | 0000000 | 00000 |
| 35mm | 72mm | 15mm | 30207M | __ | 3,250 | 14,300 | 2,100 | 15,600 | 2,900 | Required | -60° to 200° | 0000000 | 00000 |
| 40mm | 68mm | 14.5mm | 32008XM | __ | 3,000 | 16,100 | 1,900 | 17,700 | 2,700 | Required | -60° to 200° | 0000000 | 00000 |
| 50mm | 80mm | 19mm | 33010 | __ | 4,650 | 25,200 | 2,500 | 23,300 | 2,200 | Required | -60° to 200° | 0000000 | 000000 |
| 60mm | 95mm | 17.5mm | 32012X | __ | 5,600 | 29,500 | 4,100 | 37,000 | 1,800 | Required | -60° to 200° | 0000000 | 00000 |
| 70mm | 110mm | 19mm | 32014X | __ | 6,500 | 36,600 | 4,850 | 46,500 | 1,500 | Required | -60° to 200° | 0000000 | 00000 |
| 80mm | 125mm | 22mm | 32016X | __ | 9,650 | 53,500 | 7,000 | 55,500 | 1,400 | Required | -60° to 200° | 0000000 | 000000 |
Zinc-Coated Steel Ring | |||||||||||||
Open | |||||||||||||
| 3/4" | 1 25/32" | 0.475" | LM11949 | LM11910 | 1,750 | 7,200 | 910 | 6,300 | 4,900 | Required | -60° to 200° | 0000000 | 00000 |
| 1" | 1 63/64" | 0.42" | L44643 | L44610 | 1,600 | 7,400 | 1,000 | 8,050 | 3,900 | Required | -60° to 200° | 0000000 | 00000 |
| 1 1/16" | 1 63/64" | 0.42" | L44649 | L44610 | 1,600 | 7,400 | 1,000 | 8,050 | 3,900 | Required | -60° to 200° | 0000000 | 00000 |
| 1 1/4" | 2 21/64" | 0.465" | LM67048 | LM67010 | 2,100 | 10,000 | 1,500 | 12,000 | 3,400 | Required | -60° to 200° | 0000000 | 00000 |
Face-Mount Crossed-Roller Bearings
Mounting holes on the inner and outer rings allow for fastening onto hollow joints and shafts. The rollers face in alternating directions to allow for rigid, accurate motion under any combination of radial, thrust, and moment (twisting) loads. Use in applications where highly accurate motion is necessary, such as machine tools and industrial robots.
Open bearings dissipate heat more efficiently than sealed bearings.
For technical drawings and 3-D models, click on a part number.
Combined Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia., mm | For Housing ID, mm | Wd., mm | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Features | Each | |
Open | |||||||||||
| 10 | 52 | 8 | Steel | 650 | 540 | 2,400 | Required | 0° to 230° | Lubrication Groove, Two Lubrication Holes | 0000000 | 0000000 |
| 20 | 70 | 12 | Steel | 1,700 | 1,850 | 1,600 | Required | 0° to 230° | Lubrication Groove, Two Lubrication Holes | 0000000 | 000000 |
| 25 | 80 | 12 | Steel | 1,900 | 2,350 | 1,400 | Required | 0° to 230° | Lubrication Groove, Two Lubrication Holes | 0000000 | 000000 |
| 35 | 95 | 15 | Steel | 3,850 | 4,650 | 1,100 | Required | 0° to 230° | Lubrication Groove, Two Lubrication Holes | 0000000 | 000000 |
| 55 | 120 | 15 | Steel | 4,500 | 6,200 | 850 | Required | 0° to 230° | Lubrication Groove, Two Lubrication Holes | 0000000 | 000000 |
| 80 | 165 | 22 | Steel | 11,400 | 16,100 | 600 | Required | 0° to 230° | Lubrication Groove, Two Lubrication Holes | 0000000 | 000000 |
| 90 | 210 | 25 | Steel | 16,500 | 24,200 | 500 | Required | 0° to 230° | Lubrication Groove, Two Lubrication Holes | 0000000 | 000000 |
| 115 | 240 | 28 | Steel | 18,950 | 31,000 | 400 | Required | 0° to 230° | Lubrication Groove, Two Lubrication Holes | 0000000 | 000000 |
Crossed-Roller Bearings
With a considerably larger ID than our Face-Mount Crossed-Roller Bearings, use these to run hydraulic lines, electrical wiring, and other components through the inside of the bearing. The rollers face in alternating directions to allow for rigid, accurate motion under any combination of radial, thrust, and moment (twisting) loads. Use in applications where highly accurate motion is necessary, such as machine tools and industrial robots.
Open bearings dissipate heat more efficiently than sealed bearings.
For technical drawings and 3-D models, click on a part number.
Combined Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia., mm | For Housing ID, mm | Wd., mm | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Features | Each | |
Open | |||||||||||
| 20 | 31 | 5 | Steel | 310 | 290 | 2,900 | Required | 0° to 230° | __ | 0000000 | 0000000 |
| 30 | 41 | 5 | Steel | 390 | 440 | 2,100 | Required | 0° to 230° | __ | 0000000 | 000000 |
| 40 | 51 | 5 | Steel | 440 | 560 | 1,600 | Required | 0° to 230° | __ | 0000000 | 000000 |
| 50 | 61 | 5 | Steel | 510 | 710 | 1,300 | Required | 0° to 230° | __ | 0000000 | 000000 |
| 50 | 80 | 13 | Steel | 3,850 | 4,600 | 1,100 | Required | 0° to 230° | Lubrication Groove, Two Lubrication Holes | 0000000 | 000000 |
| 60 | 90 | 13 | Steel | 4,200 | 5,400 | 1,000 | Required | 0° to 230° | Lubrication Groove, Two Lubrication Holes | 0000000 | 000000 |
| 70 | 100 | 13 | Steel | 4,500 | 6,200 | 850 | Required | 0° to 230° | Lubrication Groove, Two Lubrication Holes | 0000000 | 000000 |
| 80 | 120 | 16 | Steel | 7,200 | 9,700 | 750 | Required | 0° to 230° | Lubrication Groove, Two Lubrication Holes | 0000000 | 000000 |
Spherical-Roller Bearings
Two rows of rollers give these bearings dynamic radial load capacities over five times higher than comparably sized tapered-roller bearings. Also known as rock crusher bearings, they handle heavy shock loads and are used for metal milling machinery, mining and oil field equipment, and in paper mills.
For technical drawings and 3-D models, click on a part number.
Combined Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia., mm | For Housing ID, mm | Wd., mm | Trade No. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Max. Temp. Range, °F | Each | |
Open | |||||||||||
| 25 | 52 | 18 | 22205 | Steel | 8,400 | 8,300 | 7,100 | Required | 390 | 000000 | 0000000 |
| 30 | 62 | 20 | 22206 | Steel | 11,200 | 11,200 | 6,000 | Required | 390 | 000000 | 000000 |
| 35 | 72 | 23 | 22207 | Steel | 15,500 | 15,900 | 5,300 | Required | 390 | 000000 | 000000 |
| 40 | 80 | 23 | 22208 | Steel | 25,400 | 22,300 | 6,700 | Required | 390 | 000000 | 000000 |
| 45 | 85 | 23 | 22209 | Steel | 26,500 | 24,900 | 6,000 | Required | 390 | 000000 | 000000 |
| 55 | 100 | 25 | 22211 | Steel | 33,400 | 32,300 | 5,300 | Required | 390 | 000000 | 000000 |
| 60 | 110 | 28 | 22212 | Steel | 40,000 | 39,100 | 4,800 | Required | 390 | 000000 | 000000 |
| 65 | 120 | 31 | 22213 | Steel | 49,500 | 51,500 | 4,300 | Required | 390 | 000000 | 000000 |
| 70 | 125 | 31 | 22214 | Steel | 50,500 | 52,000 | 4,000 | Required | 390 | 0000000 | 000000 |
| 75 | 130 | 31 | 22215 | Steel | 53,500 | 54,750 | 4,000 | Required | 390 | 0000000 | 000000 |
| 80 | 140 | 33 | 22216 | Steel | 59,250 | 61,750 | 3,600 | Required | 390 | 0000000 | 000000 |
| 85 | 150 | 36 | 22217 | Steel | 69,500 | 73,000 | 3,400 | Required | 390 | 0000000 | 000000 |
| 90 | 160 | 40 | 22218 | Steel | 80,750 | 88,750 | 3,200 | Required | 390 | 0000000 | 000000 |
| 95 | 170 | 43 | 22219 | Steel | 93,250 | 101,000 | 3,000 | Required | 390 | 0000000 | 000000 |
| 100 | 180 | 46 | 22220 | Steel | 102,000 | 110,000 | 2,800 | Required | 390 | 0000000 | 000000 |
| 110 | 200 | 53 | 22222 | Steel | 136,000 | 145,000 | 2,600 | Required | 390 | 0000000 | 000000 |
Combination Ball/Needle-Roller Bearings
A built-in thrust ball bearing reduces wear from adjacent shaft components, while the needle rollers support high radial loads. Install anywhere you would use separate bearings for radial and thrust loads.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | Thrust Load Cap., lbs. | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia., mm | For Housing ID, mm | Wd., mm | Ball Bearing OD, mm | Ball Bearing Wd., mm | Ring Material | Dynamic | Static | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microinch | Temp. Range, °F | Each | |
Open | |||||||||||||||
| 12 | 21 | 23 | 27 | 9 | Steel | 1,650 | 1,900 | 2,170 | 2,490 | 9,000 | Required | 8 | -20° to 230° | 00000000 | 000000 |
| 15 | 24 | 23 | 29 | 9 | Steel | 2,150 | 2,800 | 2,230 | 2,740 | 8,500 | Required | 8 | -20° to 230° | 00000000 | 00000 |
| 17 | 26 | 25 | 31 | 9 | Steel | 2,550 | 3,600 | 2,420 | 3,250 | 8,500 | Required | 8 | -20° to 230° | 00000000 | 00000 |
| 20 | 30 | 30 | 36 | 10 | Steel | 3,300 | 5,300 | 3,190 | 4,420 | 7,000 | Required | 8 | -20° to 230° | 00000000 | 00000 |
| 25 | 37 | 30 | 43 | 11 | Steel | 4,250 | 6,700 | 4,050 | 6,670 | 6,300 | Required | 8 | -20° to 230° | 00000000 | 00000 |
| 30 | 42 | 30 | 48 | 11 | Steel | 4,550 | 7,750 | 4,200 | 7,550 | 5,600 | Required | 8 | -20° to 230° | 00000000 | 000000 |
| 35 | 47 | 30 | 53 | 12 | Steel | 4,950 | 9,150 | 4,500 | 8,450 | 5,300 | Required | 8 | -20° to 230° | 00000000 | 000000 |
| 40 | 52 | 32 | 61 | 13 | Steel | 5,350 | 10,600 | 6,045 | 11,240 | 4,500 | Required | 8 | -20° to 230° | 00000000 | 000000 |
| 45 | 58 | 32 | 66.5 | 14 | Steel | 5,600 | 11,600 | 6,250 | 12,380 | 4,500 | Required | 8 | -20° to 230° | 00000000 | 000000 |
| 50 | 62 | 35 | 71.5 | 14 | Steel | 6,750 | 15,400 | 6,450 | 13,510 | 4,300 | Required | 8 | -20° to 230° | 00000000 | 000000 |