For Shaft Diameter For Shaft Diameter |
---|
|
|
|
ID ID |
---|
Lubrication Lubrication |
---|
|
For Minimum Sheet Metal Thickness For Minimum SheetMetal Thickness |
---|
|
|
Dynamic Radial Load Capacity Dynamic RadialLoad Capacity |
---|
|
Maximum Speed Maximum Speed |
---|
|
More
More
Unlike other ball bearings, these do not need to be fully inserted into a housing. A spline around the outside of the bearing creates a permanent, secure hold in thin panels. Bearings swivel to accommodate up to 5° of shaft misalignment. Shields keep out dust and contaminants. Not for use in plastic panels.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Min. Sheet Metal Thick. | Wd. | Spline OD | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Misalignment Capability | Temp. Range, °F | ABEC Rating | Each | |
Shielded | |||||||||||||
3/16" | 0.06" | 0.283" | 0.69" | Steel | 120 | 60 | 40,000 | Lubricated | 5° | -30° to 250° | ABEC-3 | 0000000 | 000000 |
1/4" | 0.06" | 0.283" | 0.69" | Steel | 120 | 60 | 40,000 | Lubricated | 5° | -30° to 250° | ABEC-3 | 0000000 | 00000 |
5/16" | 0.06" | 0.283" | 0.69" | Steel | 120 | 60 | 40,000 | Lubricated | 5° | -30° to 250° | ABEC-3 | 0000000 | 00000 |
3/8" | 0.074" | 0.37" | 1" | Steel | 380 | 180 | 36,000 | Lubricated | 5° | -30° to 250° | ABEC-3 | 0000000 | 00000 |
6mm | 1.5mm | 7.188mm | 17.5mm | Steel | 120 | 60 | 40,000 | Lubricated | 5° | -30° to 250° | ABEC-3 | 0000000 | 00000 |
8mm | 1.5mm | 7.188mm | 17.5mm | Steel | 120 | 60 | 40,000 | Lubricated | 5° | -30° to 250° | ABEC-3 | 0000000 | 00000 |
10mm | 1.9mm | 9.398mm | 25.4mm | Steel | 380 | 180 | 36,000 | Lubricated | 5° | -30° to 250° | ABEC-3 | 0000000 | 00000 |
Permanently and securely install these self-clinching bearings into panels, with no need for precision-bored holes or machined mounts. They’re often used in areas with tight space restrictions. Install them into sheet metal panels with an air-powered or hydraulic press. They’re not for use in plastic panels. These bearings are self-aligning to compensate for small amounts of shaft misalignment. Made of acetal plastic, they won’t warp or swell when exposed to water, so they’re good for use in washdown environments.
For technical drawings and 3-D models, click on a part number.
Length | Spline OD | For Minimum Sheet Metal Thickness | Dynamic Radial Load Capacity | Misalignment Capability | Temperature Range, °F | Each | |
Acetal Plastic Bearings | |||||||
---|---|---|---|---|---|---|---|
For 3/16" Shaft Diameter | |||||||
0.4" | 0.55" | 0.051" | 38 lbs. @ 120 rpm | 5° | -40° to 180° | 0000000 | 00000 |
For 1/4" Shaft Diameter | |||||||
0.4" | 0.55" | 0.051" | 38 lbs. @ 120 rpm | 5° | -40° to 180° | 0000000 | 0000 |
For 5/16" Shaft Diameter | |||||||
0.39" | 0.67" | 0.041" | 37 lbs. @ 120 rpm | 5° | -40° to 180° | 0000000 | 0000 |
For 3/8" Shaft Diameter | |||||||
0.45" | 0.67" | 0.054" | 42 lbs. @ 120 rpm | 5° | -40° to 180° | 0000000 | 0000 |
For 1/2" Shaft Diameter | |||||||
0.65" | 0.87" | 0.054" | 60 lbs. @ 120 rpm | 5° | -40° to 180° | 0000000 | 0000 |
For 5/8" Shaft Diameter | |||||||
0.77" | 1.11" | 0.058" | 145 lbs. @ 60 rpm | 5° | -40° to 180° | 0000000 | 00000 |
For 3/4" Shaft Diameter | |||||||
0.9" | 1.3" | 0.058" | 170 lbs. @ 60 rpm | 5° | -40° to 180° | 0000000 | 00000 |
Metric Acetal Plastic Bearings | |||||||
For 6mm Shaft Diameter | |||||||
10.2mm | 14mm | 1.3mm | 38 lbs. @ 120 rpm | 5° | -40° to 180° | 0000000 | 0000 |
For 8mm Shaft Diameter | |||||||
11.5mm | 17.1mm | 1.3mm | 43 lbs. @ 120 rpm | 5° | -40° to 180° | 0000000 | 0000 |
For 10mm Shaft Diameter | |||||||
11.4mm | 17.1mm | 1.3mm | 42 lbs. @ 120 rpm | 5° | -40° to 180° | 0000000 | 0000 |
For 12mm Shaft Diameter | |||||||
16.5mm | 22.1mm | 1.04mm | 60 lbs. @ 120 rpm | 5° | -40° to 180° | 0000000 | 0000 |
For 15mm Shaft Diameter | |||||||
19.4mm | 28.2mm | 1.37mm | 145 lbs. @ 60 rpm | 5° | -40° to 180° | 0000000 | 00000 |
For 16mm Shaft Diameter | |||||||
19.4mm | 28.2mm | 1.37mm | 145 lbs. @ 60 rpm | 5° | -40° to 180° | 0000000 | 00000 |
For 18mm Shaft Diameter | |||||||
22.4mm | 32.9mm | 1.47mm | 165 lbs. @ 60 rpm | 5° | -40° to 180° | 0000000 | 00000 |
For 20mm Shaft Diameter | |||||||
22.4mm | 32.9mm | 1.47mm | 165 lbs. @ 60 rpm | 5° | -40° to 180° | 0000000 | 00000 |
For 25mm Shaft Diameter | |||||||
22.9mm | 40.2mm | 1.65mm | 170 lbs. @ 60 rpm | 5° | -40° to 180° | 0000000 | 00000 |