This paper is double-bagged to keep out contaminates and meets Fed. Std. Class 100 and ISO Class 5 clean room standards.

Print signs, labels, checklists, and packing slips for use around food processing lines without the risk of contaminating the food. A thin layer of aluminum foil is laminated within this paper, so it can be picked up by a metal detector if any piece of it falls into your line.

These note pads come double-bagged to keep out contaminates and meet Fed. Spec. Class 100 and ISO Class 5 clean room standards.

Scribble notes, record measurements, and make plans, even in wet and dirty environments—the sheets in these pads are coated to repel water, oil, mud, and grease.

Take notes, make lists, or doodle.

The soft abrasive is good for fine hand-polishing of metal surfaces that require the smoothest finish possible after an abrasive sequence. Also known as crocus cloth.

Keep sanding sheets of various grits on hand.

The soft abrasive is good for fine hand-polishing of metal surfaces that require the smoothest finish possible after an abrasive sequence. Also known as crocus cloth.

These assortments include three cut-to-length sanding rolls of various grits in a convenient dispenser.

The soft abrasive is good for fine hand-polishing of soft nonferrous metals. Also known as crocus cloth.

These cut-to-length rolls resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding.

These sheets resist deterioriation when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding.

A coating prevents dust and debris from building up on the abrasive surface.

A cushioned layer gives you more control over sanding pressure, creating finer and more consistent finishes. These rolls can be cut to length.

The long sides are angled 75°.

Flexible enough to sand around curves and in corners, these sponges provide the comfort and control of a sanding block.

These sponges conform exceptionally well to small, contoured surfaces.

These cut-to-length rolls resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding. A layer of mesh lets sanding dust and debris escape during use, preventing material buildup on the abrasive surface.

A layer of mesh lets sanding dust and debris escape during use, preventing material buildup on the abrasive surface. These sheets resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding.

These assortments include a selection of sanding sponges with long-lasting diamond abrasive on one side. Flexible enough to sand around curves and in corners, they provide the comfort and control of a sanding block.

These sheets have a long-lasting diamond abrasive.

Cut the length you need, then stick to your sanding tool. When it's time to change the sheet, peel it off.

These sheets have a long-lasting diamond abrasive.

Quickly attach, remove, and reuse.

Peel and stick to your file handle. When it’s time to change the sheet, peel it off.

Cut to convenient sizes and shapes, these fit most sheet sanders.

Quickly attach, remove, and reuse these hook-and-loop sheets with triangular detail sanders.

A coating prevents dust and debris from building up on the abrasive surface.

Quickly attach, remove, and reuse these hook-and-loop sheets with pole sanders.

Press onto a compatible sanding tool or backup pad; peel off to remove.

The premium abrasive stays sharp longer.

The premium abrasive lasts longer as well as cuts faster and produces a more consistent finish than standard hook and loop discs.

Quickly attach, remove, and reuse these discs with a compatible sanding tool or backup pad.

Use with commercial floor buffing machines to sand wood floors and strip tape from concrete.

Use with 6" x 9" pads.

The small triangular pad reaches into tight corners and spaces.

Blocks hold an adhesive-back sanding roll—cut off worn abrasive and pull out more as needed.

These sanders move in a rotary motion.

Keep hands safely out of the way while deburring, sanding, and polishing workpieces on a lathe.

The orbital motion produces more consistent finishes than standard disc sanders. Also known as random orbital sanders.

These sanders have a belt release lever for quick changes.

Made of foam, these blocks flex to sand around curves.

Operate in a horizontal or vertical position.

The insulated housing reduces vibration and won’t transmit cold air to the operator’s hand.

The narrow belt is good for sanding in tight spaces.

Reach ceilings and high walls.

The abrasive-embedded nylon mesh gives you maximum control over sanding pressure.

These belts resist deterioration when used with water or cutting fluids.

The premium abrasive stays sharp longer.

The premium abrasive stays sharp longer.

These belts have a tear-resistant backing.

The abrasive-embedded mesh construction gives you more control over sanding pressure, creating finer and more consistent finishes.

A steel insert cuts into file tangs for a secure hold.

Change the insert to accommodate different files.

Also known as newsprint, this paper is a clean, low-cost fill material.

Also known as freezer paper, this paper is appropriate for food contact. A polyethylene coating on one side provides resistance to moisture and tearing.

The raised pattern provides absorbency as well as extra thickness for sharp or heavy items. This paper works well as an interleaving material.

Also known as newsprint, this paper is a clean, low-cost fill material.

These pallet liners have a layer of hexagonal cells instead of typical corrugation, so they distribute loads better than standard cardboard liners.

Plastic liners resist punctures, moisture, and many acids.

Shield iron, steel, stainless steel and tin from corrosion.

The multilayered tissue in this wrap soaks up spills and moisture while also insulating and cushioning contents.

Create high quality technical drawings with this vellum paper that is designed to work in laser printers.

Dip these strips into your liquid to quickly test water conditions.

Press onto your magnet and pole locations show up as dark green.