Maximum Diameter , Outer (Pipe) (For) Maximum Diameter ,Outer (Pipe) (For) |
---|
|
|
Probe Material Probe Material |
---|
|
Punch Operation Punch Operation |
---|
|
For Mount Type For Mount Type |
---|
|
Measure outer diameter and mark lines around pipe. A pipe size conversion chart is printed on these rulers. They’re fiber-reinforced rubber for grease, oil, gasoline, and salt water resistance.
For Pipe OD | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Inch | Metric | Lg. | Wd. | Thick. | Measuring Lg. | Front Graduation Marks (Numeric Increments) | Color | Graduation Color | Max. Temp. | Each | |
Rubber | |||||||||||
1"-6" | 2 mm-60 cm | 30" | 2 5/8" | 3/64" | 28" | 2 mm (1 cm), 16ths (1") | Gray | White | 360° F | 0000000 | 000000 |
2"-16" | 2 mm-78 cm | 60" | 3 7/8" | 3/64" | 36" | 2 mm (1 cm), 16ths (1") | Gray | White | 360° F | 0000000 | 00000 |
6"-30" | 2 mm-77 cm | 120" | 5 1/4" | 3/64" | 36" | 2 mm (1 cm), 16ths (1") | Gray | White | 360° F | 0000000 | 00000 |
Lay out pipe and structural steel for any type or size of pipe fitting—elbows, tees, and wyes of all angles. These markers are lightweight aluminum.
For Pipe OD | Angle Measuring Range | Graduation Marks (Numeric Increments) | Mount Type | Marker Type | Includes | Each | |
Anodized Aluminum | |||||||
---|---|---|---|---|---|---|---|
1 1/2"-18" | 0°-90° | 2.5° (10°) | Magnet | Soapstone Crayon | Calibrated Protractor Dials, Holder for Soapstone Crayon, Level, Magnetic Base, Triple-Jointed Marking Arm | 000000 | 0000000 |
8"-48" | 0°-90° | 2.5° (10°) | Magnet | Soapstone Crayon | Built-in Bubble Level, Calibrated Protractor Dials, Holder for Soapstone Crayon, Magnetic Base, Triple-Jointed Marking Arm | 000000 | 000000 |
Probes take the shape of a pipe joint so you can transfer the exact outline to the pipe before you cut.
Locate and mark the centerline on rods, tubes, and pipes, lay out keyways, and establish angles for connections.
Manual locator is for use with a hammer. Gently strike the rod to mark the center.
Spring-loaded locator marks the center with the pull of a trigger.
Punch Operation | Angle Measuring Range | Graduation Marks | Numeric Increments | For Min. Pipe OD | Material | Punch Material | Includes | Features | Each | |
Manual | 0°-90° | 2.5° | 10° | 1/2" | Aluminum | Steel | Adjustable Dial Protractor | Bubble Level | 000000 | 000000 |
Spring Loaded | 0°-90° | 2.5° | 10° | 1" | Aluminum | Steel | Adjustable Dial Protractor | Bubble Level | 000000 | 000000 |
Replacement Dial/Level Assembly | 0000000 | Each | 000000 |
Attach snap-on pipe markers to overhead pipe from the safety of the ground—no ladder or lift required. These applicators consist of an extendable pole and three attachable forked heads for differently sized pipe. The foam-padded plunger in the middle of each head presses your marker against pipe so it snaps on easily and without damage. To remove or adjust the marker, slide the fork between the marker and pipe.
Handle Lg., ft. | For Pipe OD | Head Material | Handle Material | For Mount Type | Includes | Each | |
4-8 | 2 1/2"-6" | Stainless Steel | Fiberglass | Wraparound | Adjustable Handle Forked Head with Foam-Padded Plunger for 2 1/2"-3 1/4" Pipe OD Forked Head with Foam-Padded Plunger for 3 3/8"- 4 1/2" Pipe OD Forked Head with Foam-Padded Plunger for 4 5/8"-6" Pipe OD | 0000000 | 0000000 |
6-11 | 2 1/2"-6" | Stainless Steel | Fiberglass | Wraparound | Adjustable Handle Forked Head with Foam-Padded Plunger for 2 1/2"-3 1/4" Pipe OD Forked Head with Foam-Padded Plunger for 3 3/8"- 4 1/2" Pipe OD Forked Head with Foam-Padded Plunger for 4 5/8"-6" Pipe OD | 0000000 | 000000 |
Roll adhesive-back pipe markers onto overhead pipe, tube, duct, or conduit without taking a single step up a ladder. Stick one end of your marker onto the head so it doesn’t fall as you raise the extendable pole. Then use the foam roller to apply the marker to pipe smoothly and securely.