Marks made with this paint fade in approximately 30 days when exposed to sunlight and traffic.

Apply sealer (sold separately) over paint for up to 30 days of added protection.

These sheets are made of rubber and iron oxide, letting you create a nonmetallic, nonmagnetic surface that magnets will stick to. Sheets can be cut with scissors to create custom shapes and sizes.

Used to insulate, create grips, and color-code components, these coatings resist high temperatures, light abrasion, and corrosion.

Rubber coatings withstand salt and acids.

PVC plastic coatings can be used on nearly any surface, including rubber. They withstand salt, acids, alkalies, and gasoline. They also resist UV light, so they won’t lose their color when exposed to sunlight over long periods of time.

Coatings in a can can be dipped, brushed, or sprayed.

Primers and topcoats cannot be sold outside of the United States due to product regulations.

VOC (Volatile Organic Compounds) regulations restrict sales to the listed jurisdictions/areas.

Use these coatings on tanks to create a low-friction lining that prevents bubble formation and turbulence in the liquids within. These thick coatings can also be used in chutes and on foundations for a smooth, glossy surface that resists abrasion, chemicals, and extreme temperatures once cured. Apply with a brush or roller. The size listed is the combined total of the two parts.

Longer-lasting than antislip tape, these coatings contain grit to provide traction. They’re good for areas with pedestrian traffic.

Water-based epoxy coatings are clear and can be applied over nearly any surface, even old coatings, without altering their appearance. These two-part coatings come with a mixer that attaches to a hand-held drill and a roller cover to apply them once mixed. The size listed is the combined total of the two parts.

Apply gallon-sized water-based coatings with a roller. Coatings that comply with OSHA 29 CFR 1910.22 meet requirements for walking-working surfaces.

Made with Viton® fluoroelastomer, use these coatings to create a flexible coating on rollers, heavy equipment, and anything else that’s exposed to corrosive chemicals or extreme temperatures. Coatings resist acids, alkalies, fuels, and solvents, as well as temperatures as low as -40° F once cured. They can also be used as an adhesive for Viton® gaskets, O-rings, and seals.

Apply coatings in a bottle and can with a brush or roller. The size listed is the combined total of the two parts.

These coatings reflect up to 60% of the sun's rays. They also restore and reinforce your roof by forming a water-resistant seal. Apply to a dry surface with a sprayer or brush. Cannot be sold to CA, CO, CT, DE, MD, RI, and UT due to VOC regulations.

Reflect at least 85% of the sun's rays to reduce cooling costs. These coatings also restore and reinforce your roof by filling cracks and forming a water-resistant seal. Apply to a dry surface with a brush, roller, or sprayer.

Primer (sold separately) extends the life of the coating. It’s required for use on bare rubberized and aged asphalt roofs.

Use these coatings to form a water-resistant layer to restore and reinforce your roof. Apply to a dry surface with a sprayer or brush. They cannot be sold to California because they exceed local regulatory limits on VOCs (volatile organic compounds).

Grit in these coatings provides traction and fills hairline cracks. Coatings form a weather- and water-resistant seal to protect and revitalize asphalt surfaces. Apply with a squeegee or brush.

Protect and revitalize asphalt surfaces with these tar-free coatings that form a weather- and water-resistant seal. Apply with a squeegee or brush.

Roll out a fast fix for leaky roofs and gutters with these peel-and-stick rolls. Backing is rubberized asphalt adhesive. Roll can be cut to size. Use primer (sold separately) for optimal adhesion.

Repair holes and seal gaps in roofing and gutters. These patching compounds are durable and water resistant.

Apply acrylic compounds to dry surfaces. Apply asphalt compounds to wet or dry surfaces.

These patching compounds are the most flexible and watertight we offer. Developed for use on flashing, chimneys, and high-stress areas, they are highly vibration resistant.

Dispense compounds in a cartridge in a standard caulk gun (sold separately).

Compounds that cannot be sold to the regions listed exceed local regulatory limits on VOCs (volatile organic compounds).

Reinforce hot- and cold-applied asphalt patching compounds and coatings with this flexible fabric.

Make a temporary repair to cracks in any flat roof. These patching compounds are a powder that forms a thick gel in minutes when poured directly into standing water and rain.

Used on ceramic, concrete, and stone floor and wall tiles, grout consists of fine sand, masonry cement, and coloring. Apply with a grout float.

Acrylic grout does not require mixing. It resists shrinking, cracking, and staining.

Stop active leaks of up to 50 gallons per minute in concrete, brick, and stone. These crack fillers begin to harden within seconds to create a permanent fix that won't shrink. When fully cured they create a seal that can withstand pressure of up to 2,000 psi. Apply with a dispensing gun (sold separately). The size listed is the combined total of the two parts. A mixer nozzle is included.

Stop slow-flowing and weeping leaks in concrete. These crack fillers begin to harden in three to five minutes to create a permanent fix that won't shrink.

Polyurethane fillers are thin to penetrate deep into cracks. When fully cured they create a seal that can withstand pressure of up to 2,000 psi. Apply with a standard caulk gun (sold separately). For especially large cracks, use a packer (sold separately) with a grease gun or a grout pump.

Spread patching compounds in dry, wet, and even water-filled holes. Compress them with a tamper or shovel and they are immediately ready for traffic.

These crack fillers come in an easy-to-pour jug for filling cracks in asphalt up to 1/2" wide. They’re ready for traffic in 2 to 5 days.