11mm ID Bearings | McMaster-Carr

Made of naturally slippery plastic so you’ll never have to add lubricant. They’re ideal for clean environments where you need to prevent oil drips or graphite flakes. Compared to metal bearings, they are lighter and will never rust.

Flanged sleeve bearings combine a sleeve and thrust bearing in one. The flange supports thrust loads and prevents the bearing from being pushed out of place. The sleeve is the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

Moisture-Resistant Ultra-Low-Friction Plastic Blend—These bearings won't warp or swell from humidity or direct contact with water. They glide effortlessly for applications with frequent starts and stops, such as conveyor systems.

	For Housing ID, mm	Lg., mm	Flange OD, mm	Flange Thk., mm	Dynamic Radial Load Cap. @ Speed	Dynamic Thrust Load Cap. @ Speed	Color	Temp. Range, ° F		Each
Moisture-Resistant Ultra-Low-Friction Plastic Blend



	11	13	5	18	1	60 lb. @ 120 rpm	105 lb. @ 120 rpm	Yellow	-50 to 190	2705T141	00000

Ball Screw/Splines and Bearings

From one compact system, transmit linear or rotary motion or both at once (sometimes called spiral motion). Because of these different motions, these ball screw/splines and bearings create efficient, fluid movements in complex automated applications, such as pick-and-place robots.

The ball bearings move smoothly and precisely, even at high speeds. They're powered independently, so you can drive one bearing at a time or both together to coordinate movements.

The ball screw/splines are hardened on the surface, so they stand up to repeated motion. They’re also hollow, so you can run electrical wiring, compressed air tubing, coolants, or lubricant through their center.

	Spline		Thread						Ball Screw Bearing				Ball Spline Bearing
	Lg., mm	No. of	Lg., mm	Direction, ° F	Thread Direction	ID, mm	Lg., mm	Root Dia., mm	OD, mm	Overall Lg., mm	Dynamic Load Cap., lb.	Static Load Cap., lb.	OD, mm	Overall Lg., mm	Dynamic Load Cap., lb.	Static Load Cap., lb.	Max. Dynamic Torque, in·lbf		Each
1055 Carbon Steel







				16 mm Dia. (Tolerance: -0.018 mm to 0 mm)

				500	6	360	5 to 176	Right Hand	11	500	15.15	32	40	870	1,610	31	50	1,590	2,830	277	4049N13	000000000

Dry-Running Thrust Bearings

Made of naturally slippery plastic so there's no lubricant to maintain or make a mess. These bearings are ideal for spic-and-span spaces since oil won't drip off, wash out, or collect dust over time. They'll also never rust.

Moisture-Resistant Plastic Blend—Similar to acetal, these bearings won't warp or swell from water or humidity.

	OD, mm	Thk., mm	Dynamic Thrust Load Cap. @ Speed	Color	Temp. Range, ° F		Each
Moisture-Resistant Plastic Blend



	11	15	1	13 lb. @ 120 rpm	Gray	-40 to 260	8920N48	00000


	11	27	0.5	75 lb. @ 120 rpm	Gray	-40 to 260	8920N49	0000

Metric Press-Fit Drill Bushings

Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to precisely guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part. Known for their versatility, drill bushings are also used as spacers, shims, and machinery bushings. These bushings are made of hardened, ground steel that holds its shape and resists wear, so they last for many cycles without needing to be replaced.

All bushings have a chamfer on the outside that centers the bushing as you place it into the hole. Press into place with a manual or hydraulic press. Since the bushing is sized slightly larger than the hole for an extremely tight fit, it’ll stay put permanently. These are ANSI Type PM bushings—also known as headless bushings—which means you don’t need to counterbore the hole to mount them flush.

They also have an internal chamfer that makes it easy to insert bits, pins, and punches without damaging the bushing or misaligning tools.

Don't see the size you need? Additional sizes are available.

Both Ends—Bushings with an internal chamfer on both ends allow you to insert tools no matter which end of the bushing is inserted into the jig. However, having an internal chamfer on the bottom of your bushing may cause shavings to get caught and bind as you remove the bit.

DIN 179—DIN 179 bushings meet dimensional and material standards that make sure they're compatible with other parts and tools. Although DIN 179 is no longer an active standard, it's still a common reference point for designers.

						Tolerance, mm								Each
	OD, mm	Lg., mm	Internal Chamfer	For Drill Bit Size, mm	For Drill Bit Size Decimal Equiv.	ID	OD	Lg.	Drill Bushing Type	Material	Hardness	Specs. Met		1-5	6-11	12-Up
11 mm ID



		18	12	One End	11	0.4331"	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	DIN 179	96990A371	000000	000000	00000


		18	12	Both Ends	11	0.4331"	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	—	97060A334	00000	00000	00000
		18	20	One End	11	0.4331"	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	DIN 179	96990A372	00000	00000	00000
		18	20	Both Ends	11	0.4331"	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	—	97060A335	00000	00000	00000
		18	25	One End	11	0.4331"	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	DIN 179	96990A373	00000	00000	00000
		18	25	Both Ends	11	0.4331"	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	—	97060A336	00000	00000	00000

Metric Press-Fit Drill Bushings with Head


Shown in Countersunk Hole	Shown in Standard Hole

Even under extreme drilling pressure, these metric bushings won't press through your jig plate. They’re ANSI Type H bushings, also known as headed bushings. A flanged head acts as a stop, so these bushings won’t move as you push down your drill bit, reamer, or other cutting bit. Use them even in jigs made of thin or soft materials—the head adds support to protect your jig from damage caused by heavy use. Drill bushings ensure accurate, consistent cuts and drilled holes from one part to the next. They’re also used as spacers, shims, and machinery bushings. Made of hardened, ground steel, these bushings hold their shape and resist wear, so they last for many cycles without needing to be replaced.

These bushings meet DIN 172 dimensional standards. This standard is no longer active, but it’s often used as a reference point for making sure parts are compatible with other parts and tools.

To install, fit the bushing into a hole in your jig. In a standard hole, the head will sit above the jig plate; to mount flush, install in a countersunk hole. A chamfered edge on the bottom of the bushing helps center the bushing in the hole. Once it’s centered, press the bushing into the hole with a hydraulic or lever press.

					Head, mm		Tolerance, mm								Each
	OD, mm	Lg., mm	For Drill Bit Size, mm	For Drill Bit Size Decimal Equiv.	OD	Thk.	ID	OD	Lg.	Drill Bushing Type	Material	Hardness	Specs. Met		1-5	6-11	12-Up
11 mm ID



		18	8	11	0.4331"	22	4	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	H	Steel	Rockwell C61	DIN 172	96977A390	000000	000000	00000


		18	16	11	0.4331"	22	4	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	H	Steel	Rockwell C61	DIN 172	96977A391	00000	00000	00000
		18	21	11	0.4331"	22	4	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	H	Steel	Rockwell C61	DIN 172	96977A392	00000	00000	00000