About Plain Bearings
More
Oil-Embedded Sleeve Bearings
![](/prerenderstable/mvPRE/contents/gfx/imagecache/639/6391k214p1-d03c-digitall@halfx_637055105703313267.png?ver=imagenotfound)
Startup friction causes these bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID, mm | Lg., mm | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 8 mm Shaft Dia. | |||||||
---|---|---|---|---|---|---|---|
10 | 15 | 370 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 000000 |
For 15 mm Shaft Dia. | |||||||
19 | 15 | 690 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
20 | 15 | 690 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
21 | 15 | 690 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
22 | 15 | 690 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
For 17 mm Shaft Dia. | |||||||
22 | 15 | 790 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
For 20 mm Shaft Dia. | |||||||
25 | 15 | 930 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
For 22 mm Shaft Dia. | |||||||
27 | 15 | 1,000 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
High-Load Dry-Running Sleeve Bearings
![](/prerenderstable/mvPRE/contents/gfx/imagecache/606/60695k5p1-d03c-digital@halfx_637051207601409897.png?ver=imagenotfound)
Plastic Bearings
with Steel Shell
A metal shell adds strength.
Bronze-backed PTFE bearings with steel shell combine high-load and high-speed capabilities. They resist swelling when exposed to moisture and are electrically conductive.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Dynamic Radial Load Capacity | Temperature Range, °F | Each | |
Metric Bronze-Backed PTFE Plastic Bearings with Steel Shell | |||||
---|---|---|---|---|---|
For 10mm Shaft Dia. | |||||
12mm | 15mm | 930 lbs. @ 120 rpm | -320° to 530° | 0000000 | 00000 |
For 12mm Shaft Dia. | |||||
14mm | 15mm | 930 lbs. @ 120 rpm | -320° to 530° | 0000000 | 0000 |
For 14mm Shaft Dia. | |||||
16mm | 15mm | 1,850 lbs. @ 60 rpm | -320° to 530° | 0000000 | 0000 |
For 24mm Shaft Dia. | |||||
27mm | 15mm | 1,850 lbs. @ 60 rpm | -320° to 530° | 0000000 | 0000 |
Light Duty Dry-Running Sleeve Bearings
![](/prerenderstable/mvPRE/contents/gfx/imagecache/261/2610t21p1-d03c-digitall@halfx_637051674841837494.png?ver=imagenotfound)
Use where high loads and speeds are not required.
Acetal bearings have low moisture absorption and are more chemical resistant than nylon and MDS-filled nylon bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Dynamic Radial Load Capacity | Color | Temperature Range, °F | Each | |
Metric Nylon Bearings | ||||||
---|---|---|---|---|---|---|
For 8mm Shaft Dia. | ||||||
10mm | 15mm | 46 lbs. @ 120 rpm | Off-White | -10° to 220° | 00000000 | 000000 |
Metric Acetal Bearings | ||||||
For 12mm Shaft Dia. | ||||||
16mm | 15mm | 50 lbs. @ 120 rpm | White | -20° to 180° | 0000000 | 0000 |
For 14mm Shaft Dia. | ||||||
20mm | 15mm | 100 lbs. @ 60 rpm | White | -20° to 180° | 0000000 | 0000 |
Ultra-Low-Friction Dry-Running Sleeve Bearings
![](/prerenderstable/mvPRE/contents/gfx/imagecache/263/2639t23p1-d03c-digitall@halfx_637051674143660163.png?ver=imagenotfound)
Use these bearings in applications with frequent starts and stops because they operate with very little friction.
PTFE bearings have good chemical resistance.
Thermoplastic-blend bearings create the least amount of friction of any bearings that we offer. They handle heavier loads than PTFE and Rulon J bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For Housing ID | Lg. | Dynamic Radial Load Capacity | Color | Temperature Range, °F | Each | |
Metric PTFE Plastic Bearings | ||||||
---|---|---|---|---|---|---|
For 12mm Shaft Dia. | ||||||
16mm | 15mm | 18 lbs. @ 120 rpm | White | -350° to 500° | 0000000 | 00000 |
For 14mm Shaft Dia. | ||||||
20mm | 15mm | 37 lbs. @ 60 rpm | White | -350° to 500° | 0000000 | 00000 |
Metric Thermoplastic Blend Bearings | ||||||
For 10mm Shaft Dia. | ||||||
12mm | 15mm | 260 lbs. @ 120 rpm | Yellow | -55° to 190° | 00000000 | 0000 |
For 12mm Shaft Dia. | ||||||
14mm | 15mm | 260 lbs. @ 120 rpm | Yellow | -55° to 190° | 00000000 | 0000 |
Food Industry Dry-Running Sleeve Bearings
![](/prerenderstable/mvPRE/contents/gfx/imagecache/577/57785k67p1-d03c-digitall@halfx_637051675817699955.png?ver=imagenotfound)
Made of FDA-listed materials or FDA compliant, these bearings are for use in food applications. They also withstand caustic and washdown environments.
Acetal bearings are FDA compliant for direct contact with food. They’re also bright blue, making them easy to spot if they fall into your line.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Dynamic Radial Load Capacity | Color | Temperature Range, °F | Specifications Met | Each | |
Metric Acetal Plastic Bearings | |||||||
---|---|---|---|---|---|---|---|
For 10mm Shaft Dia. | |||||||
12mm | 15mm | 160 lbs. @ 120 rpm | Blue | -50° to 190° | FDA Compliant 21 CFR 177.1550 | 00000000 | 00000 |
For 14mm Shaft Dia. | |||||||
16mm | 15mm | 320 lbs. @ 60 rpm | Blue | -50° to 190° | FDA Compliant 21 CFR 177.1550 | 00000000 | 0000 |
For 15mm Shaft Dia. | |||||||
17mm | 15mm | 320 lbs. @ 60 rpm | Blue | -50° to 190° | FDA Compliant 21 CFR 177.1550 | 00000000 | 0000 |
For 16mm Shaft Dia. | |||||||
18mm | 15mm | 320 lbs. @ 60 rpm | Blue | -50° to 190° | FDA Compliant 21 CFR 177.1550 | 00000000 | 0000 |
For 18mm Shaft Dia. | |||||||
20mm | 15mm | 320 lbs. @ 60 rpm | Blue | -50° to 190° | FDA Compliant 21 CFR 177.1550 | 00000000 | 0000 |
For 25mm Shaft Dia. | |||||||
28mm | 15mm | 320 lbs. @ 60 rpm | Blue | -50° to 190° | FDA Compliant 21 CFR 177.1550 | 00000000 | 0000 |
Metric UHMW Plastic Bearings | |||||||
For 12mm Shaft Dia. | |||||||
16mm | 15mm | 37 lbs. @ 120 rpm | White | -200° to 180° | FDA Compliant 21 CFR 177.1520 | 0000000 | 0000 |
For 14mm Shaft Dia. | |||||||
20mm | 15mm | 75 lbs. @ 60 rpm | White | -200° to 180° | FDA Compliant 21 CFR 177.1520 | 0000000 | 0000 |
Water-Resistant Dry-Running Sleeve Bearings
![](/prerenderstable/mvPRE/contents/gfx/imagecache/636/6362k145p1-d03c-digitall@halfx_637054668369587967.png?ver=imagenotfound)
Good for underwater applications, these bearings won’t swell or warp when wet.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
ID | For Housing ID | Lg. | Dynamic Radial Load Capacity | Color | Temperature Range, °F | Each | |
Rulon LR Plastic Bearings | |||||||
---|---|---|---|---|---|---|---|
For 12mm Shaft Dia. | |||||||
12.1mm | 16mm | 15mm | 185 lbs. @ 120 rpm | Maroon | -400° to 550° | 000000 | 000000 |
Recycled Plastic Dry-Running Sleeve Bearings
![](/prerenderstable/mvPRE/contents/gfx/imagecache/765/7650n12_b743ab37-480b-4c6e-a77d-11b805c9a739@halfx_i1huj_1715354730.png?ver=imagenotfound)
Reduce your carbon footprint without sacrificing performance. Made of recycled thermoplastic, these bearings are a sustainable alternative to standard plastic dry-running bearings.
For technical drawings and 3-D models, click on a part number.
For Housing ID, mm | Lg., mm | Dynamic Radial Load Capacity | Color | Temperature Range, °F | Each | |
Thermoplastic Blend Bearings | ||||||
---|---|---|---|---|---|---|
For 16 mm Shaft Dia. | ||||||
18 | 15 | 450 lbs. @ 60 rpm | Gray | -40° to 265° | 0000000 | 00000 |
Flame-Retardant Dry-Running Sleeve Bearings
![](/prerenderstable/mvPRE/contents/gfx/imagecache/649/6499n14_f97198df-7cc7-4427-a68a-f28fa411c49c@halfx_39bsh_1717419373.png?ver=imagenotfound)
Rated UL94 V-0, these bearings meet strict fire protection requirements for flame retardance. They’re self-lubricating, so they wear less and last longer than standard sleeve bearings.
For technical drawings and 3-D models, click on a part number.
Static-Control Dry-Running Sleeve Bearings
![](/prerenderstable/mvPRE/contents/gfx/imagecache/764/7640n14_bd505a3e-00df-4bab-ad92-0205ac568d5a@halfx_2x15l_1715028300.png?ver=imagenotfound)
Made of thermoplastic, these bearings conduct electricity to prevent static buildup in moving equipment. They’re self-lubricating, which reduces friction and prevents wear. They’re often used in applications that can’t have metal bearings or lubricants.
For technical drawings and 3-D models, click on a part number.
Oil-Embedded Flanged Sleeve Bearings
![](/prerenderstable/mvPRE/contents/gfx/imagecache/633/6338k419c3-d03c-digital-master1569879013-p9@halfx_637054673023484059.png?ver=imagenotfound)
Startup friction causes these bearings to release a thin layer of oil on the bearing’s surface. They’re flanged, so they handle loads both parallel and perpendicular to the shaft. They’re also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
Metric 841 Bronze Bearings | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
For 15mm Shaft Dia. | ||||||||||
21mm | 15mm | 27mm | 3mm | 690 lbs. @ 60 rpm | 1,200 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | 10° to 220° | 00000000 | 00000 |
For 20mm Shaft Dia. | ||||||||||
26mm | 15mm | 32mm | 3mm | 930 lbs. @ 60 rpm | 800 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | 10° to 220° | 00000000 | 0000 |
For 22mm Shaft Dia. | ||||||||||
28mm | 15mm | 34mm | 3mm | 1,000 lbs. @ 60 rpm | 1,600 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 0000000 | 0000 |
Light Duty Dry-Running Flanged Sleeve Bearings
![](/prerenderstable/mvPRE/contents/gfx/imagecache/270/2705t28--9a0fc58fd61605198647-p9@halfx_637407738498197238.png?ver=imagenotfound)
Use where high loads and speeds are not required.
Acetal bearings have low moisture absorption and are more chemical resistant than nylon and MDS-filled nylon bearings.
Thermoplastic-blend bearings have low moisture absorption and create very low friction in applications with light loads, and frequent starts and stops.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Color | Temperature Range, °F | Each | |
Acetal Bearings | |||||||||
---|---|---|---|---|---|---|---|---|---|
For 12mm Shaft Dia. | |||||||||
16mm | 15mm | 24mm | 2mm | 50 lbs. @ 120 rpm | 47 lbs. @ 120 rpm | White | -40° to 180° | 0000000 | 00000 |
For 14mm Shaft Dia. | |||||||||
20mm | 15mm | 26mm | 3mm | 100 lbs. @ 60 rpm | 95 lbs. @ 60 rpm | White | -40° to 180° | 0000000 | 0000 |
Thermoplastic-Blend Bearings | |||||||||
For 16mm Shaft Dia. | |||||||||
22mm | 15mm | 28mm | 3mm | 360 lbs. @ 60 rpm | 360 lbs. @ 60 rpm | Yellow | -50° to 190° | 00000000 | 0000 |
For 20mm Shaft Dia. | |||||||||
26mm | 15mm | 32mm | 3mm | 360 lbs. @ 60 rpm | 370 lbs. @ 60 rpm | Yellow | -50° to 190° | 00000000 | 0000 |
Ultra-Low-Friction Dry-Running Flanged Sleeve Bearings
![](/prerenderstable/mvPRE/contents/gfx/imagecache/270/2706t28--830c5b7f0a61610478769-p9@halfx_637460539880578309.png?ver=imagenotfound)
Use these bearings in applications with frequent starts and stops because they operate with very little friction.
PTFE bearings have good chemical resistance.
Rulon J bearings stand up to higher temperatures than PTFE and thermoplastic-blend bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Color | Temperature Range, °F | Specifications Met | Each | |
PTFE Plastic Bearings | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
For 22 mm Shaft Dia. | ||||||||||
28mm | 15mm | 34mm | 3mm | 37 lbs. @ 60 rpm | 38 lbs. @ 60 rpm | White | -200° to 450° | FDA Compliant 21 CFR 177.1550 | 00000000 | 000000 |
Rulon J Plastic Bearings | ||||||||||
For 10 mm Shaft Dia. | ||||||||||
14mm | 15mm | 18mm | 2mm | 140 lbs. @ 120 rpm | 90 lbs. @ 120 rpm | Gold | -400° to 500° | __ | 00000000 | 00000 |
For 12 mm Shaft Dia. | ||||||||||
16mm | 15mm | 20mm | 2mm | 140 lbs. @ 120 rpm | 90 lbs. @ 120 rpm | Gold | -400° to 500° | __ | 00000000 | 00000 |
Metric Press-Fit Drill Bushings
![](/prerenderstable/mvPRE/contents/gfx/imagecache/969/96990a403p1-a06a-digitall@halfx_637133939270486603.png?ver=imagenotfound)
Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part. Known for their versatility, drill bushings are also used as spacers, shims, and machinery bushings. These bushings are made of hardened, ground steel that holds its shape and resists wear, so they last for many cycles without needing to be replaced.
All bushings have a chamfer on the outside that centers the bushing as you place it into the hole. Press into place with a manual or hydraulic press. They also have internal chamfers, so it's easier to insert bits, pins, and punches into the bushing. DIN 179 bushings meet dimensional and material standards that make sure they're compatible with other parts and tools. Although DIN 179 is no longer an active standard, it's still a common reference point for designers.
Don't see the size you need? Additional sizes are available.
For technical drawings and 3-D models, click on a part number.
Tolerance | Each | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
OD, mm | Lg., mm | Internal Chamfer | For Drill Bit Size | ID, mm | OD, mm | Lg., mm | Drill Bushing Type | Material | Hardness | Specifications Met | 1-5 | 6-11 | 12-Up | |
25 mm ID | ||||||||||||||
31 | 15 | One End | 25 mm | 0.02 to 0.041 | 0.017 to 0.033 | -0.2 to 0.2 | PM | Steel | Rockwell C61 | DIN 179 | 000000000 | 000000 | 000000 | 000000 |
Metric Press-Fit Drill Bushings with Head
![](/prerenderstable/mvPRE/contents/gfx/imagecache/969/96977a421-1574804965-p9@halfx_637103822480009782.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/i14/i147-length--40b2880035c1610474410-p9@halfx_637460496132093226.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/4x-/4x-flushincounterborehole-1610136778-p9@halfx_637457119842706889.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/i20/i200-sittingonjigplate--196346194331611091392-p9@halfx_637466665960604012.png?ver=imagenotfound)
Even under extreme drilling pressure, these metric bushings won't press through your jig plate. A flanged head on the top of the bushing acts as a stop, preventing it from moving as you push down your drill bit, reamer, or other cutting bit. Drill bushings ensure accurate, consistent cuts and drilled holes from one part to the next. They sometimes also work as spacers, shims, and machinery bushings. Made of hardened, ground steel, these bushings hold their shape and resist wear over time. The flanged head protects your jig plate from damage caused by heavy use.
Although it's no longer an active standard, DIN 172 is still a common reference point for making sure parts are compatible with other parts and tools.
These bushings work in both countersunk and standard drill holes. To install, place the bushing inside the hole in your jig. A chamfered edge on the bottom of the bushing helps center the bushing in the hole. Once centered, press the bushing into the hole with a hydraulic or lever press.
For technical drawings and 3-D models, click on a part number.
Head | Tolerance | Each | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
OD, mm | Lg., mm | OD, mm | Thick., mm | ID, mm | OD, mm | Lg., mm | Drill Bushing Type | Material | Hardness | Specifications Met | 1-5 | 6-11 | 12-Up | |
18.5 mm ID | ||||||||||||||
30 | 15 | 34 | 5 | 0.02 to 0.041 | 0.015 to 0.028 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 000000 | 000000 | 000000 |
19 mm ID | ||||||||||||||
30 | 15 | 34 | 5 | 0.02 to 0.041 | 0.015 to 0.028 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
19.5 mm ID | ||||||||||||||
30 | 15 | 34 | 5 | 0.02 to 0.041 | 0.015 to 0.028 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
20 mm ID | ||||||||||||||
30 | 15 | 34 | 5 | 0.02 to 0.041 | 0.015 to 0.028 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
20.5 mm ID | ||||||||||||||
30 | 15 | 34 | 5 | 0.02 to 0.041 | 0.015 to 0.028 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
21 mm ID | ||||||||||||||
30 | 15 | 34 | 5 | 0.02 to 0.041 | 0.015 to 0.028 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
21.5 mm ID | ||||||||||||||
30 | 15 | 34 | 5 | 0.02 to 0.041 | 0.015 to 0.028 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
22 mm ID | ||||||||||||||
30 | 15 | 34 | 5 | 0.02 to 0.041 | 0.015 to 0.028 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
22.5 mm ID | ||||||||||||||
35 | 15 | 39 | 5 | 0.02 to 0.041 | 0.017 to 0.033 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
23 mm ID | ||||||||||||||
35 | 15 | 39 | 5 | 0.02 to 0.041 | 0.017 to 0.033 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
23.5 mm ID | ||||||||||||||
35 | 15 | 39 | 5 | 0.02 to 0.041 | 0.017 to 0.033 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
24 mm ID | ||||||||||||||
35 | 15 | 39 | 5 | 0.02 to 0.041 | 0.017 to 0.033 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
24.5 mm ID | ||||||||||||||
35 | 15 | 39 | 5 | 0.02 to 0.041 | 0.017 to 0.033 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
25 mm ID | ||||||||||||||
35 | 15 | 39 | 5 | 0.02 to 0.041 | 0.017 to 0.033 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
25.5 mm ID | ||||||||||||||
35 | 15 | 39 | 5 | 0.02 to 0.041 | 0.017 to 0.033 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
26 mm ID | ||||||||||||||
35 | 15 | 39 | 5 | 0.02 to 0.041 | 0.017 to 0.033 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |