32mm Length Bearings | McMaster-Carr

Filter by

DFARS Compliance

System of Measurement

Length

Material

RoHS Compliance

Bearing Type

Dynamic Radial Load Capacity @ Speed

For Housing ID

For Load Direction

Lubrication

Maximum Temperature

Minimum Temperature

Plain Bearing Type

Shaft Diameter

Shaft Mount Type

Shaft Type

REACH Compliance

Lubricant

Lubrication Method

Dynamic Thrust Load Capacity @ Speed

Flange OD

Forward

How can we improve?

63 Products

About Plain Bearings

Startup friction causes these bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Metric 841 Bronze Bearings

For 16 mm Shaft Dia.
For Housing ID, mm	Lg., mm	Dynamic Radial Load Capacity	Lubrication	Lubricant	Temperature Range, °F		Each
20	32	1,550 lbs. @ 60 rpm	Lubricated	SAE 30 Oil	-35° to 300°	00000000	00000
For 20 mm Shaft Dia.
24	32	1,950 lbs. @ 60 rpm	Lubricated	SAE 30 Oil	-35° to 300°	00000000	0000
For 25 mm Shaft Dia.
32	32	2,450 lbs. @ 60 rpm	Lubricated	SAE 30 Oil	-35° to 300°	00000000	00000
For 32 mm Shaft Dia.
40	32	3,150 lbs. @ 30 rpm	Lubricated	SAE 30 Oil	-35° to 300°	00000000	00000

High-Load Oil-Embedded Sleeve Bearings

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds. Startup friction causes them to release a thin layer of oil on the bearing’s surface. Color is silver because of the iron. These bearings are also magnetic due to the high iron content.

863 iron-copper bearings are also known as Super Oilite® bearings.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

863 Iron-Copper Bearings

For 32mm Shaft Dia.
For Housing ID	Lg.	Dynamic Radial Load Capacity	Lubrication	Lubricant	Temperature Range, °F		Each
40mm	32mm	5,600 lbs. @ 30 rpm	Lubricated	SAE 90 Oil	-15° to 300°	00000000	000000

Iron-Copper Bearings

For 20mm Shaft Dia.
For Housing ID	Lg.	Dynamic Radial Load Capacity	Lubrication	Lubricant	Temperature Range, °F		Each
24mm	32mm	6,000 lbs. @ 60 rpm	Lubricated	SAE 90 Oil	10° to 510°	00000000	000000

Ultra-Low-Friction Oil-Embedded Sleeve Bearings

For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Metric 841 Bronze Bearings

For 32mm Shaft Dia.
For Housing ID, mm	Lg., mm	Dynamic Radial Load Capacity	Lubrication	Lubricant	Temperature Range, °F		Each
40	32	3,150 lbs. @ 30 rpm	Lubricated	SAE 20 Oil with PTFE	-60° to 300°	00000000	000000

High-Load Ultra-Low-Friction Oil-Embedded Sleeve Bearings

With extra iron and filled with oil containing slippery PTFE, these bearings support heavy loads that frequently start and stop along shafts. Startup friction causes a thin layer of oil to release onto the surface. Their high iron content also means they resist failing if their load suddenly and drastically increases, but they won’t run as fast as standard bearings.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

863 Iron-Copper
For Housing ID, mm	Length, mm	Dynamic Radial Load Capacity	Lubrication	Lubricant	Temperature Range, °F		Each
For 25 mm Shaft Dia.
32	32	2,800 lbs. @ 60 rpm	Lubricated	SAE 20 Oil with PTFE	-60° to 300°	00000000	000000

Oil-Embedded Flanged Sleeve Bearings

Startup friction causes these bearings to release a thin layer of oil on the bearing’s surface. They’re flanged, so they handle loads both parallel and perpendicular to the shaft. They’re also known as Oilite® bearings.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Metric 841 Bronze Bearings
For Housing ID	Lg.	Flange OD	Flange Thick.	Dynamic Radial Load Capacity	Dynamic Thrust Load Capacity	Lubrication	Lubricant	Temperature Range, °F		Each
For 20mm Shaft Dia.
26mm	32mm	32mm	3mm	1,950 lbs. @ 60 rpm	800 lbs. @ 60 rpm	Lubricated	SAE 30 Oil	10° to 220°	00000000	000000
For 32mm Shaft Dia.
38mm	32mm	46mm	4mm	3,150 lbs. @ 30 rpm	2,650 lbs. @ 30 rpm	Lubricated	SAE 30 Oil	-35° to 300°	00000000	00000
For 35mm Shaft Dia.
40mm	32mm	45mm	2.5mm	3,450 lbs. @ 30 rpm	1,900 lbs. @ 30 rpm	Lubricated	SAE 30 Oil	-35° to 300°	00000000	00000
For 45mm Shaft Dia.
51mm	32mm	57mm	3mm	4,450 lbs. @ 30 rpm	2,950 lbs. @ 30 rpm	Lubricated	SAE 30 Oil	-35° to 300°	00000000	00000
For 50mm Shaft Dia.
60mm	32mm	70mm	5mm	4,950 lbs. @ 30 rpm	5,800 lbs. @ 30 rpm	Lubricated	SAE 30 Oil	-35° to 300°	00000000	00000

High-Load Oil-Embedded Flanged Sleeve Bearings

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds. Startup friction causes these bearings to release a thin layer of oil onto their surface. Color is silver because of the iron.

863 iron-copper bearings are also known as Super Oilite® bearings.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

863 Iron-Copper Bearings
For Housing ID	Lg.	Flange OD	Flange Thick.	Dynamic Radial Load Capacity	Dynamic Thrust Load Capacity	Lubrication	Lubricant	Temperature Range, °F		Each
For 32mm Shaft Dia.
38mm	32mm	46mm	4mm	5,600 lbs. @ 30 rpm	3,250 lbs. @ 30 rpm	Lubricated	ISO 460 Oil	-15° to 300°	00000000	000000
For 35mm Shaft Dia.
40mm	32mm	45mm	2.5mm	5,600 lbs. @ 30 rpm	2,400 lbs. @ 30 rpm	Lubricated	ISO 460 Oil	-15° to 300°	0000000	00000
For 45mm Shaft Dia.
51mm	32mm	57mm	3mm	5,600 lbs. @ 30 rpm	2,950 lbs. @ 30 rpm	Lubricated	ISO 460 Oil	-15° to 300°	00000000	00000
For 50mm Shaft Dia.
60mm	32mm	70mm	5mm	5,600 lbs. @ 30 rpm	4,700 lbs. @ 30 rpm	Lubricated	ISO 460 Oil	-15° to 300°	00000000	00000

High-Load Ultra-Low-Friction Oil-Embedded Flanged Sleeve Bearings

With oil for reduced friction and iron for added strength, these bearings handle frequent stops and starts in high-load applications. They withstand greater weight and shock loads than standard bearings, but operate at lower speeds.

For technical drawings and 3-D models, click on a part number.

863 Iron-Copper Bearings
For Housing ID, mm	Length, mm	Flange OD, mm	Flange Thickness, mm	Dynamic Radial Load Capacity	Dynamic Thrust Load Capacity	Lubrication	Lubricant	Temperature Range, °F		Each
32 mm Shaft Dia.
38	32	46	4	5,600 lbs. @ 30 rpm	3,250 lbs. @ 30 rpm	Lubricated	ISO 460 Oil	-60° to 300°	00000000	000000
35 mm Shaft Dia.
40	32	45	2.5	5,600 lbs. @ 30 rpm	2,400 lbs. @ 30 rpm	Lubricated	ISO 460 Oil	-60° to 300°	00000000	00000
45 mm Shaft Dia.
51	32	57	3	5,600 lbs. @ 30 rpm	2,950 lbs. @ 30 rpm	Lubricated	ISO 460 Oil	-60° to 300°	00000000	00000
50 mm Shaft Dia.
60	32	70	5	5,600 lbs. @ 30 rpm	4,700 lbs. @ 30 rpm	Lubricated	ISO 460 Oil	-60° to 300°	00000000	00000

Multipurpose Flanged Sleeve Bearings

These bronze bearings are strong, wear resistant, and excellent at handling shock loads. They’re sometimes called 660 leaded bronze bearings.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Metric 932 Bearing Bronze Bearings
For Housing ID	Lg.	Flange OD	Flange Thick.	Dynamic Radial Load Capacity	Dynamic Thrust Load Capacity	Lubrication	Temperature Range, °F	PV Max.		Each
For 28mm Shaft Dia.
36mm	32mm	44mm	4mm	5,550 lbs. @ 30 rpm	5,600 lbs. @ 30 rpm	Required	-350° to 450°	__	00000000	000000
For 32mm Shaft Dia.
38mm	32mm	46mm	4mm	6,300 lbs. @ 30 rpm	5,300 lbs. @ 30 rpm	Required	-350° to 450°	75,000	00000000	00000
For 45mm Shaft Dia.
51mm	32mm	57mm	3mm	8,900 lbs. @ 30 rpm	5,950 lbs. @ 30 rpm	Required	-350° to 450°	75,000	0000000	00000

Metric Press-Fit Drill Bushings

Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part. Known for their versatility, drill bushings are also used as spacers, shims, and machinery bushings. These bushings are made of hardened, ground steel that holds its shape and resists wear, so they last for many cycles without needing to be replaced.

All bushings have a chamfer on the outside that centers the bushing as you place it into the hole. Press into place with a manual or hydraulic press. They also have internal chamfers, so it's easier to insert bits, pins, and punches into the bushing. DIN 179 bushings meet dimensional and material standards that make sure they're compatible with other parts and tools. Although DIN 179 is no longer an active standard, it's still a common reference point for designers.

Don't see the size you need? Additional sizes are available.

For technical drawings and 3-D models, click on a part number.

				Tolerance								Each
OD, mm	Lg., mm	Internal Chamfer	For Drill Bit Size	ID, mm	OD, mm	Lg., mm	Drill Bushing Type	Material	Hardness	Specifications Met		1-5	6-11	12-Up
16.25 mm ID
35	32	One End	16.25 mm	0.016 to 0.034	0.017 to 0.033	-0.3 to 0.3	PM	Steel	Rockwell B61	DIN 179	000000000	000000	000000	000000
21.25 mm ID
35	32	One End	21.25 mm	0.02 to 0.041	0.017 to 0.033	-0.3 to 0.3	PM	Steel	Rockwell C61	DIN 179	000000000	00000	00000	00000

				Tolerance								Each
OD, mm	Lg., mm	Internal Chamfer	For Drill Bit Size	ID, mm	OD, mm	Lg., mm	Drill Bushing Type	Material	Hardness	Specifications Met		1-5	6-11	12-Up
25.75 mm ID
35	32	One End	25.75 mm	0.02 to 0.041	0.017 to 0.033	-0.3 to 0.3	PM	Steel	Rockwell B61	DIN 179	000000000	000000	000000	000000

Metric Press-Fit Drill Bushings with Head

Shown in Countersunk Hole

Shown in Standard Hole

Even under extreme drilling pressure, these metric bushings won't press through your jig plate. A flanged head on the top of the bushing acts as a stop, preventing it from moving as you push down your drill bit, reamer, or other cutting bit. Drill bushings ensure accurate, consistent cuts and drilled holes from one part to the next. They sometimes also work as spacers, shims, and machinery bushings. Made of hardened, ground steel, these bushings hold their shape and resist wear over time. The flanged head protects your jig plate from damage caused by heavy use.

Although it's no longer an active standard, DIN 172 is still a common reference point for making sure parts are compatible with other parts and tools.

These bushings work in both countersunk and standard drill holes. To install, place the bushing inside the hole in your jig. A chamfered edge on the bottom of the bushing helps center the bushing in the hole. Once centered, press the bushing into the hole with a hydraulic or lever press.

For technical drawings and 3-D models, click on a part number.

		Head		Tolerance								Each
OD, mm	Lg., mm	OD, mm	Thick., mm	ID, mm	OD, mm	Lg., mm	Drill Bushing Type	Material	Hardness	Specifications Met		1-5	6-11	12-Up
12.1 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	000000	000000	000000
12.2 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
12.3 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
12.4 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
12.5 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
12.6 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
12.7 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
12.8 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
12.9 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
13 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
13.1 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
13.2 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
13.3 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
13.4 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
13.5 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
13.6 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
13.7 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
13.8 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
13.9 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
14 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
14.1 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
14.2 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
14.3 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
14.4 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
14.5 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
14.6 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
14.7 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
14.8 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
14.9 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
15 mm ID
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
15.5 mm ID
26	32	30	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
16 mm ID
26	32	30	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
16.5 mm ID
26	32	30	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
17 mm ID
26	32	30	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
17.5 mm ID
26	32	30	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
18 mm ID
26	32	30	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000