Slip these bearings onto a shaft and secure with the included set screws, no special tools required. All have an extended inner ring for additional shaft support.

Bearings with a black-oxide steel ring have some corrosion resistance.

Shielded bearings dissipate heat more efficiently than sealed bearings.

Sealed bearings block out dust and other contaminants better than shielded bearings.

Bearings with a retaining ring have a removable retaining ring that holds the bearing inside a housing.

For technical drawings and 3-D models, click on a part number.

Quickly secure these bearings onto shafts with the clamp-on collar for a concentric, mar-free hold. Tighten the single screw on the locking collar around its inner ring on your shaft to center and secure the shaft in the bearing bore. The collar’s firm grip reduces vibration and noise in your system. The steel rings on these bearings have a black-oxide finish for some corrosion resistance.

For technical drawings and 3-D models, click on a part number.

Secure these bearings in washdown areas, such as food, beverage, pharmaceutical, and chemical plants, by tightening the set screw onto a shaft—no additional collar needed. Similar to 304 stainless steel, the nickel-coated steel rings on these bearings won’t break down from water. The extended inner ring increases shaft support. All of these bearings have NSF registered H1 lubrication, which is certified for incidental contact with food.

For technical drawings and 3-D models, click on a part number.

Designed to stand up to frequent washdowns, you can quickly secure these ball bearings onto shafts with the clamp-on collar in food, beverage, pharmaceutical, and chemical plants. The collar centers your shafts and secures them better than set screw ball bearings, which reduces vibration and noise. To install these bearings, tighten the single screw on the collar around its inner ring on your shaft for a mar-free hold.

Coated with nickel, the steel rings on these bearings won’t corrode from water and harsh cleaners, similar to 304 stainless steel. The inner ring is extended for added shaft support. All of these bearings have NSF registered H1 lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.

For technical drawings and 3-D models, click on a part number.

Found anywhere from machine tool spindles to conveyor rollers, these bearings have a two-piece design that allows for adjustment.

For technical drawings and 3-D models, click on a part number.

Also known as drawn-cup roller bearings, these are our thinnest roller bearings. The outer ring is drawn out to form a lip that holds the bearing together. Bearings take on the shape of their housing and may be oblong prior to installation.

Open bearings dissipate heat more efficiently than sealed bearings.

Sealed bearings block out dust better than open bearings, but retain more heat.

For technical drawings and 3-D models, click on a part number.

Install these bearings directly onto hardened and ground shafts. They have higher load capacity, speed, and accuracy than standard needle-roller bearings.

Open bearings dissipate heat more efficiently than sealed bearings.

Shaft liners allow you to use the bearing on unhardened and unground shafts.

For technical drawings and 3-D models, click on a part number.

Mount these bearings on a support rail shaft for applications requiring maximum rigidity. All have end seals to keep lubricant in and dirt out. To install, slide bearings into a housing (not included). For bearings with retaining ring grooves, secure with two retaining rings (sold individually).

Self-aligning bearings compensate for shaft misalignment.

Fixed-alignment bearings are for use where shaft misalignment is unlinkely.

For technical drawings and 3-D models, click on a part number.

Designed for heavy loads, these bearings have higher load capacities than comparable standard linear ball bearings for support rails. Use them for applications that require maximum rigidity. All are self-aligning to compensate for shaft misalignment. To install, slide bearings into a housing (not included). For bearings with retaining ring grooves, secure with two retaining rings (sold individually).

Bearings with end seals keep lubricants in and dirt out.

Bearings with stainless steel balls are more corrosion resistant than bearings with steel balls.

For technical drawings and 3-D models, click on a part number.

Mount these bearings on a support rail shaft for applications requiring maximum rigidity. To install, slide bearings into a housing (not included) and secure with two retaining rings (sold individually).

Bearings with 0.0005" shaft clearance are best for precision applications. Bearings with 0.001" or 0.0015" shaft clearance are less likely to bind on your shaft than bearings with 0.0005" shaft clearance.

Self Aligning—Bearings compensate for shaft misalignment.

Fixed Alignment—Bearings are for use where shaft misalignment is unlikely.

Frelon-lined bearings are wear and chemical resistant. Note: Not for use with bare aluminum, chrome-plated steel, or 300 series stainless steel shafts.

PTFE-lined bearings are chemical resistant and nonabrasive. They have a ceramic coating for added corrosion resistance.

For technical drawings and 3-D models, click on a part number.

Designed to handle heavy loads, these bearings have higher load capacities than comparable standard mounted linear ball bearings for support rails. Use them for applications that require maximum rigidity. All are self-aligning to compensate for shaft misalignment and have end seals to keep lubricant in and dirt out.

For technical drawings and 3-D models, click on a part number.

Virtually maintenance free, these bearings have slippery, chemical-resistant liners that don't require added lubrication. Mount them on a support rail shaft for applications requiring maximum rigidity.

Bearings with 0.0005" shaft clearance are best for precision applications. Bearings with 0.001" or 0.0015" shaft clearance are less likely to bind on your shaft than bearings with 0.0005" shaft clearance.

Self Aligning—Bearings compensate for shaft misalignment.

Fixed Alignment—Bearings are for use where shaft misalignment is unlikely.

Frelon liners are stronger and more wear resistant than PTFE liners.

For technical drawings and 3-D models, click on a part number.

A ceramic liner makes high speeds as well as rapid acceleration and deceleration possible. Mount these bearings on a support rail shaft for applications requiring maximum rigidity. End seals keep contaminants out. These bearings are self-aligning to compensate for shaft misalignment. Note: Not for use with ceramic-coated aluminum or 300 series stainless steel shafts.

For technical drawings and 3-D models, click on a part number.

Found in hand-powered clamps, vises, grates, doors, and work tables, lead screws and nuts have broad, square threads that are well suited for quick assembly, high clamping forces, and lifting and lowering heavy objects. To ensure compatibility, please select components that have the same thread direction, thread size, and number of thread starts.

360 brass components have excellent machinability and good corrosion resistance.

Travel distance per turn, also known as screw lead, is the distance a nut or handle moves with one revolution of the lead screw.

For technical drawings and 3-D models, click on a part number.