System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter |
|---|
|
Seal Type Seal Type |
|---|
|
ID ID |
|---|
|
OD OD |
|---|
|
For Housing ID For Housing ID |
|---|
|
Bearing Trade Number Bearing Trade Number |
|---|
Ball Bearing Type Ball Bearing Type |
|---|
 | With Retaining Ring |
Bearing Type Bearing Type |
|---|
 | Ball |
Width Width | Show |
|---|
|
Width Width | Hide |
|---|
For Load Direction For Load Direction |
|---|
 | Radial |
Ring Material Ring Material |
|---|
|
ABEC Rating ABEC Rating |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Maximum Temperature Maximum Temperature |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
Retaining Ring OD Retaining Ring OD |
|---|
|
Retaining Ring Thickness Retaining Ring Thickness |
|---|
|
Ring Finish Ring Finish |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
About Ball and Roller Bearings
More
Set Screw Collar Ball Bearings
Slip these bearings onto a shaft and secure with the included set screws, no special tools required. All have an extended inner ring for additional shaft support.
Bearings with a black-oxide steel ring have some corrosion resistance.
Sealed bearings block out dust and other contaminants better than shielded bearings.
Bearings with a retaining ring have a removable retaining ring that holds the bearing inside a housing.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Retaining Ring | Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | OD | Wd. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | ABEC Rating | Each | |
Sealed (Lubricated) | ||||||||||||||
Black-Oxide Steel—With Retaining Ring | ||||||||||||||
| ER208 | 40mm | 80mm | 27.8mm | 52.4mm | 49.2mm | 86.5mm | 1.6mm | 7,300 | 4,450 | 4,150 | -20° to 220° | ABEC-1 | 0000000 | 0000000 |
Washdown Clamp-On Collar Ball Bearings
Designed to stand up to frequent washdowns, you can quickly secure these ball bearings onto shafts with the clamp-on collar in food, beverage, pharmaceutical, and chemical plants. The collar centers your shafts and secures them better than set screw ball bearings, which reduces vibration and noise. To install these bearings, tighten the single screw on the collar around its inner ring on your shaft for a mar-free hold.
Coated with nickel, the steel rings on these bearings won’t corrode from water and harsh cleaners, similar to 304 stainless steel. The inner ring is extended for added shaft support. All of these bearings have NSF registered H1 lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Retaining Ring | Radial Load Capacity, lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | For Housing ID | Wd. | OD | OD Tolerance | Wd. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
Sealed | |||||||||||||||
Nickel-Coated Steel Ring | |||||||||||||||
| 40mm | 80mm | 27.8mm | 71.8mm | Not Rated | 50.8mm | 86.5mm | 1.6mm | 7,300 | 4,450 | 1,750 | Lubricated | -20° to 220° | ABEC-1 | 0000000 | 0000000 |