McMaster-Carr logo
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    35 Products

    Clamps for Parts Inspection

    Image of ProductInUse. Front orientation. Coordinate Measuring Machine Plates and Fixtures. Clamps for Parts Inspection.
    With a light yet sturdy hold, these clamps help you keep workpieces in place hands-free for measuring and inspecting. Thread them right into your fixturing surface, whether it’s a plate, tower, or table. Because they apply less pressure than machining clamps, they won’t distort your parts, so you can take accurate measurements. While these clamps aren’t sturdy enough for use in machining, you can still use them for light fabrication work, such as laser engraving.
    Hold-Down Clamps
    Image of Product. Front orientation. Coordinate Measuring Machine Plates and Fixtures. Clamps for Parts Inspection, Tension Spring.

    Tension Spring

    Image of Product. Front orientation. Coordinate Measuring Machine Plates and Fixtures. Clamps for Parts Inspection, Wire Tension Spring.

    Wire

    Tension

    Spring

    Image of Product. Front orientation. Coordinate Measuring Machine Plates and Fixtures. Clamps for Parts Inspection, Thumb Screw.

    Thumb

    Screw

    Image of Product. Front orientation. Coordinate Measuring Machine Plates and Fixtures. Clamps for Parts Inspection, Squeeze Tabs.

    Squeeze

    Tabs

    Hold-down clamps secure parts from the top.
    Tension Spring—Tension spring clamps are the most common type of clamp. Slide the arm down the shaft until it touches the top of your workpiece. Since you apply pressure directly, using too much force might move your part.
    Wire Tension Spring—Wire tension spring clamps have a slimmer profile than standard clamps, which means they don’t cover up as much of your workpiece. They’re often used to clamp small parts. Pull the wire arm away from the shaft, position your part, then release the arm so it moves back to cradle your part in place.
    Thumb Screw—Clamps with a thumb screw give you more control over the pressure you apply on a workpiece than tension spring clamps. Twisting the screw moves the clamp up or down in small increments, so they’re less likely to dent or scratch your workpiece. The knurled head on the screw is slip resistant, letting you make precise turns with reliable grip.
    Squeeze Tabs—Clamps with squeeze tabs on the back are best for supporting delicate parts. They have the lightest touch of any clamps we offer, because the tension is held in the tabs rather than the clamp itself. Press the tabs together like a clothespin and rotate the clamp where you need it.
    Rubber-Coated Tip—Clamps with a rubber-coated tip are less likely to scrape parts than clamps with an uncoated tip.
    Clamps
    Replacement
    Mounting Shafts
    Replacement
    Clamp Arms
    Reach
    Lg.
    Ht.
    Thread
    Lg.
    Material
    Tip Finish
    Each
    Each
    Each
    Tension Spring
     
    1/4"-20 Threads
    13/16"1"1/4"Aluminum—6203N27000000———0———0
    13/16"2"1/4"Aluminum—1337N2600000———0———0
    1 9/16"2 3/4"1/4"Aluminum—1728N9100000———0———0
    1 9/16"2 3/4"1/4"AluminumRubber Coated1728N9300000———0———0
    2 5/16"2 3/4"1/4"Aluminum—1728N9200000———0———0
    2 5/16"2 3/4"1/4"AluminumRubber Coated1728N9400000———0———0
    3 7/16"3"1/4"Aluminum—1337N2500000———0———0
     
    M4 × 0.7 mm Threads
    21 mm50 mm4.5 mmAluminum—1337N3700000———0———0
    38 mm50 mm4.5 mmAluminum—1337N3500000———0———0
    58 mm50 mm4.5 mmAluminum—1337N3600000———0———0
     
    M6 × 1 mm Threads
    21 mm50 mm6.2 mmAluminum—1337N3400000———0———0
    38 mm75 mm6.2 mmAluminum—1337N3200000———0———0
    58 mm75 mm6.2 mmAluminum—1337N3300000———0———0
     
    M8 × 1.25 mm Threads
    38 mm75 mm6.2 mmAluminum—1337N2900000———0———0
    58 mm75 mm6.2 mmAluminum—1337N3100000———0———0
     
    Wire Tension Spring
     
    1/4"-20 Threads
    1 1/4"1"1/4"Aluminum—1337N2700000———0———0
    2"2"1/4"Aluminum—1337N2800000———0———0
     
    Thumb Screw
     
    1/4"-20 Threads
    1 9/16"1 1/2"3/8"Aluminum—6203N1100000———0———0
    3"2 1/2"1/4"Aluminum—6203N1200000———0———0
    4 3/8"3 1/2"3/8"Aluminum—6203N13000000———0———0
     
    M6 × 1 mm Threads
    40 mm38 mm9.5 mmAluminum—6203N1400000———0———0
    76 mm63 mm6.4 mmAluminum—6203N1500000———0———0
    112 mm89 mm9.5 mmAluminum—6203N16000000———0———0
     
    Squeeze Tabs
     
    1/4"-20 Threads
    3 1/4"3"3/8"Plastic—6203N21000006203N180000006203N17000000
     
    M6 × 1 mm Threads
    83 mm76 mm9.5 mmPlastic—6203N22000006203N19000006203N1700000
     
    Side Clamps
    Image of Product. Front orientation. Coordinate Measuring Machine Plates and Fixtures. Clamps for Parts Inspection, Side Clamps.
    Side clamps don’t block access to the top of your workpiece like hold-down clamps. They push one side of your workpiece against another barrier, such as a standoff, support, or corner plate. Made of durable yet flexible plastic, the outer edge of the clamp slightly contracts when you pull the circular trigger—like drawing a bow.
    Lg.
    Wd.
    Ht.
    Thread
    Lg.
    Material
    Each
     
    1/4"-20 Threads
    3 1/16"2 5/8"1/2"3/4"Plastic6203N23000000
     
    M6 × 1 mm Threads
    77 mm66 mm13 mm19 mmPlastic6203N2400000
     
    Positioning Clamps
    Image of Product. Front orientation. Coordinate Measuring Machine Plates and Fixtures. Clamps for Parts Inspection, Positioning Clamps.
    Positioning clamps give you the most flexible setup of any clamps. They’re the best choice for curved or irregular shapes, such as cylinders. Both sliding pins on each arm have an O-ring that compresses when you push them tight against a workpiece. The O-ring cushions the pressure you apply, and it also gives grip while protecting parts from scratches. With an arm that rotates 360°, you can create movable supports. These clamps also have a magnetic flange to help secure metal parts.
    Opening
    Reach
    Lg.
    Min.
    Max.
    Lg.
    Wd.
    Ht.
    Thread
    Lg.
    Material
    Pair
     
    1/4"-20 Threads
    3/4"7/16"2 3/4"3 5/8"9/16"2 1/2"1/4"Aluminum6203N250000000
     
    M6 × 1 mm Threads
    19 mm11 mm57 mm92 mm12.7 mm63 mm6.4 mmAluminum6203N26000000
     

    Fixturing for Parts Inspection

    Image of ProductInUse. Front orientation. Coordinate Measuring Machine Plates and Fixtures. Fixturing for Parts Inspection.
    From towers and brackets to standoffs and supports, these components are the building blocks for your custom fixturing setup. They elevate parts so you can access a variety of angles for measuring and inspecting while protecting your measuring device from hitting the inspection table. You’ll often see them used with coordinate measuring machines (CMMs). They’re not for use in machining applications.
    Kits
    Image of Product. Front orientation. Coordinate Measuring Machine Plates and Fixtures. Fixturing for Parts Inspection, Kits.
    Kits come with a base set of clamps, standoffs, and other supports for positioning parts. Add other components, such as magnetic V-supports, to expand your starter toolkit for complex setups.
    No. of
    Pieces
    Includes
    Each
    1/4"-20 Threads
    433 Hold-Down Clamps—1 9/16" Reach × 3" O'all Ht.
    3 Hold-Down Clamps—2 5/16" Reach × 3" O'all Ht.
    3 Standoffs—1/2" Dia. × 3/4" Ht.
    3 Standoffs—1/2" Dia. × 2" Ht.
    3 Standoffs—3/4" Dia. × 3/4" Ht.
    3 Standoffs—3/4" Dia. × 2" Ht.
    6 Standoffs—1/2" Dia. × 1" Ht.
    6 Standoffs—3/4" Dia. × 1" Ht.
    3 Pin Supports—1/2" Dia. × 1/2" Ht.
    3 Pin Supports—3/4" Dia. × 1/2" Ht.
    3 Cone Supports
    1 Adjustable-Height Sleeve for Standoffs
    2 Positioning Plates
    1 Wood Stand    		1355N850000000
    633 Hold-Down Clamps—1 9/16" Reach × 3" O'all Ht.
    3 Hold-Down Clamps—2 5/16" Reach × 3" O'all Ht.
    2 Toggle Clamps with Mounting Plate
    3 Standoffs—1/2" Dia. × 3/4" Ht.
    3 Standoffs—1/2" Dia. × 2" Ht.
    3 Standoffs—3/4" Dia. × 3/4" Ht.
    3 Standoffs—3/4" Dia. × 2" Ht.
    3 Standoffs—1" Dia. × 3/4" Ht.
    3 Standoffs—1" Dia. × 2" Ht.
    6 Standoffs—1/2" Dia. × 1" Ht.
    6 Standoffs—3/4" Dia. × 1" Ht.
    6 Standoffs—1" Dia. × 1" Ht.
    1 Precision Adjustable-Height Standoff—1/2" Dia.
    3 Pin Supports—1/2" Dia. × 1/2" Ht.
    3 Pin Supports—3/4" Dia. × 1/2" Ht.
    6 Cone Supports
    2 Any-Angle Cone Supports
    1 Adjustable-Height Sleeve for Standoffs
    2 Positioning Plates
    1 Wood Stand    		1355N9500000000
     
    M6 Threads
    422 Hold-Down Clamps—38 mm Reach × 38 mm O'all Ht.
    4 Hold-Down Clamps—58 mm Reach × 75 mm O'all Ht.
    3 Standoffs—13 mm Dia. × 20 mm Ht.
    3 Standoffs—13 mm Dia. × 25 mm Ht.
    3 Standoffs—13 mm Dia. × 50 mm Ht.
    3 Standoffs—19 mm Dia. × 20 mm Ht.
    3 Standoffs—19 mm Dia. × 25 mm Ht.
    3 Standoffs—19 mm Dia. × 50 mm Ht.
    3 Standoffs—25 mm Dia. × 20 mm Ht.
    3 Standoffs—25 mm Dia. × 25 mm Ht.
    3 Standoffs—25 mm Dia. × 50 mm Ht.
    1 Adjustable-Height Standoff—13 mm Dia.
    2 Pin Supports—13 mm Dia. × 25 mm Ht.
    3 Cone Supports
    1 Positioning Plate—35 mm Lg.
    1 Positioning Plate—76 mm Lg.
    1 Acetal Plastic Tray    		1409N51000000
     
    back to top