You can set these counters up to count with or without voltage inputs based on the switch, sensor, or encoder you have. An output relay sends a signal to another device when the counter reaches a set point. The signal can start/stop a process or trigger an alarm. If power is lost, count backup maintains the count and programming backup maintains settings.

The digits displayed on these counters are visible up to 100 ft. away and the display can be adjusted to suit lighting conditions. You can set counters up to count with or without voltage inputs based on the switch, sensor, or encoder you have. Counters can be wired for remote reset. They are protected against dust and washdowns and can be used outdoors (rated NEMA 4X). Programming backup maintains settings if power is lost.

Wire these counters/ratemeters to an electrical pulse-emitting switch, sensor, or encoder to count input while tracking rates in units such as gallons per minute. A scaling function lets you adjust the unit of measure to suit your application. Use the toggle button to switch between the count and the rate. IP or NEMA rated, they protect against dust and washdowns and can be used outdoors.

For quick installation, these counters/ratemeters fit a standard _1/8 DIN panel cutout. Wire them up to an electrical pulse-emitting switch, sensor, or encoder to count input while tracking rates in units such as gallons per minute. The scaling function lets you adjust the unit of measure to suit your application. Counters are protected from dust and washdowns and can be used outdoors (rated NEMA 4X).

You can set these counters up to count with or without voltage inputs based on the switch, sensor, or encoder you have. Count backup maintains the count if power is lost.

The digits displayed on these counters are visible up to 100 ft. away and the display can be adjusted to suit lighting conditions. You can set counters up to count with or without voltage inputs based on the switch, sensor, or encoder you have. They can be wired for remote reset. An output relay sends a signal to another device when a set point is reached. The signal can start/stop a process or trigger an alarm. Counters are protected from dust and washdowns and can be used outdoors (rated NEMA 4X). Programming backup maintains settings if power is lost.

At a glance, quickly read counts and rates in units, such as gallons per minute. The display on these counters/ratemeters is visible up to 130 ft. away—almost half of a football field—and gets brighter or dimmer based on your lighting. They have an output relay, so you can program them to start or stop a process or trigger an alarm when they reach their setpoint. These counters/ratemeters count using either a voltage or switch contact input, so they work with most sensors, encoders, and switches. You can wire them to reset remotely.

Press the button on the display to toggle between the count and rate. You can also program these counters/ratemeters to toggle automatically between the count and rate every few seconds. With the scaling function, you can change the unit of measure. Hardwire them to power the display. They have a programming backup, so if you lose power you won't lose your settings.

IP65 and NEMA 4X rated, these counters/ratemeters stand up to dust, rain, snow, and washdowns.

Using ultrasonic waves, these transmitters measure the flow rate of your liquid from outside your pipe. They're a good choice for applications where you need to retrofit your system or avoid liquid coming into contact with the transmitter. Also known as transducers, these transmitters convert measurements to an electrical pulse that can be interpreted by receiving devices, such as remote displays and programmable logic controllers (PLCs). The pulse outputs match the input voltage of the transmitter. The higher the flow, the more pulses they send. For your receiving device to interpret the signal, you will need to calibrate it for the measurement range and output signal of the transmitter. They only give accurate readings within the rated measurement range. Configure them for either a 4-20mA or digital pulse output when installing.

A digital display makes it easy to check flow rate and configure settings. Clamp these transmitters onto your pipe with the included mounting hardware and gel pads. They measure flow no matter the mounting orientation.

These transmitters are calibrated with water but can be used with other liquids and will generally measure accurately, even if they differ in viscosity and density. You can recalibrate them in the field for accurate readings on pipe and operating conditions.

For the Manufacturer User Manual, click on a part number and select Product Detail.

Display running time on a machine so you can schedule preventative maintenance.

Display running time on a machine so you can schedule preventative maintenance.

Thread mounting hardware (sold separately) into your pipe connection and insert the probe of these transmitters to measure the flow and temperature of water, oil, or air. The probe is held in place with a compression fitting on the other end of the mounting hardware. They’re often used in large-diameter pipes where it would be difficult to install a transmitter inline. To calculate the flow rate, these transmitters generate a small amount of heat, then measure the cooling effect your liquid or air has on it. They measure and output both flow and temperature, making them ideal for applications where temperature fluctuates. Also known as transducers, they convert measurements to an electrical signal that can be interpreted by receiving devices, such as remote displays and programmable logic controllers (PLCs) to monitor flow or control equipment. As flow or temperature increases, the output signal increases. For your receiving device to interpret the signal, you will need to calibrate it for the measurement range and output signal of the transmitter. They only give accurate readings within the rated measurement range. They’ll measure flow correctly in any mounting orientation. These transmitters are calibrated with air, glycol solutions, oil, and water but can be recalibrated in the field for other liquids.

Adjust settings at the source using the digital display. These transmitters have two configurable outputs. One can be wired for flow or temperature as an analog output or a digital switch. The other one can be wired for flow as a digital switch, digital pulse output, or IO Link. Pulse outputs send flow data using spikes of voltage that match the input voltage of the transmitter. The higher the flow, the more pulses they send. To change settings and receive error messages remotely from your PLC or computer, you can program one of the outputs to use IO Link. You’ll need an IO Link controller (not included) to connect to your interface.

For the Manufacturer User Manual, click on a part number and select Product Detail.

Send flow rate and temperature measurements simultaneously to a programmable logic controller (PLC), data logger, or other receiving device. Used to monitor status or control equipment, these transmitters, also known as transducers, convert measurements to an electrical signal that is interpreted by receiving devices. As flow or temperature increases, the output signal increases. For your receiving device to interpret the signal, you will need to calibrate it for the measurement range and output signal of the transmitter. They only give accurate readings within the rated measurement range. Mount them inline with your pipe system. They’ll measure flow correctly in any mounting orientation.

A digital display makes it easy to view readings and adjust settings at the source. To change settings and receive error messages remotely from your PLC or computer, program one of the outputs to use IO Link. You’ll need an IO Link controller (not included) to connect to your interface.

For the Manufacturer User Manual, click on a part number and select Product Detail.

Send flow rate measurements to monitor and control equipment. Also known as transducers, these transmitters convert flow rate measurements to an electrical signal that can be interpreted by receiving devices, such as remote displays and programmable logic controllers (PLCs). As flow increases, the output signal increases. For your receiving device to interpret the signal, you will need to calibrate it for the measurement range and output signal of the transmitter. They only give accurate readings within the rated measurement range. Mount them directly inline with your system. They measure flow correctly no matter their mounting orientation.

These transmitters are calibrated with water. You can use them with other liquids, but they may not measure accurately if the liquid’s viscosity differs from water.

For the Manufacturer User Manual, click on a part number and select Product Detail.