Use these wheels for light grinding, deburring, and sharpening.

The perforated honeycomb pattern cuts carbide, ceramics, and glass without the need for cleaning.

Use these wheels for precision grinding on surface, cylindrical, and tool and cutter grinders. They are also known as Type 1 wheels and straight wheels.

The special shapes of these wheels provide more clearance than typical straight wheels.

The porous bond leaves more space between abrasive grains so heavy amounts of chips and coolant easily flow through.

A good value for everyday use, these wheels offer an economical balance between heavy material removal and long life. They are also known as Type 27 wheels, raised-hub wheels, and grinding discs.

A blend of ceramic alumina and zirconia alumina removes material at a 50% faster rate than our Long-Life Grinding Wheels. Wheels are also known as Type 27 wheels, raised-hub wheels, and grinding discs.

The absence of iron, sulfur, and chlorine in these wheels means they won’t corrode or discolor stainless steel. They are also known as INOX wheels, Type 27 wheels, raised-hub wheels, and grinding discs.

Heat-dissipating holes reduce material buildup and extend the life of the wheel. Wheels have a semiflexible backing that conforms to curved and rough surfaces.

Multiple layers of nylon mesh embedded with abrasive provide a cushioned grind. Also known as unitized discs or wheels.

A blend of cotton laminate and aluminum oxide creates a smoother surface than other grinding wheels with similar grits. Wheels are also known as Type 27 wheels and raised-hub wheels.

Wheels have a large surface area and a thick layer of rough abrasive for heavy material removal on concrete and stone. They are also known as Type 11 wheels, flared-cup wheels, snagging wheels, and cup stones.

Use these wheels for heavy material removal in one spot or along a weld seam. They are also known as Type 1 wheels and snagging wheels.

Also known as hooded dressers, these cleaners reveal new layers of sharp abrasive and deflect flying chips.

The larger face offers better control, while multiple points provide a finer finish than single-point cleaners.

Twist the knurled adjustment knob on these cleaners to advance the replaceable point.

Furnished with multiple points, these clean faster and leave a more uniform finish than single-point cleaners.

Use to clean or create rounded shapes on the wheel surface.

Mount these truing cleaners to a T-slot to reshape worn diamond and CBN grinding wheels.

Made of aluminum oxide, these bits are well suited for use on most metals and materials that are not heat sensitive.

Bits thread onto mounted shanks so you can quickly switch head shapes without removing the shank. The abrasive grains are blended with rubber, which cushions during grinding to produce a smoother surface texture than other bits with similar grits.

The abrasive grains in these bits are blended with rubber, which cushions during grinding to produce a smoother surface texture than other bits with similar grits.

Use bits in any drill chuck that accepts a 1/4" hex shank.

Similar to diamond, boron nitride is harder than aluminum oxide and lasts longer. Bits are also known as jig grinding pins and mandrels.

Each set contains a selection of our most popular grinding bits.

The diamond abrasive in these bits is extremely hard and lasts longer than tungsten carbide. For longer tool life and improved finish, use a water- or oil-soluble mist or coolant.

With more flaps than standard discs, these last 30-40% longer.

With more flaps than standard discs, these last 30-40% longer.

The abrasive-embedded mesh construction gives you more control over sanding pressure, creating more consistent finishes.

The flaps alternate between an abrasive to remove material and a lubricant that minimizes heat to reduce discoloration of the work surface.

The flaps wrap around the outer edge of these discs to sand welds at right angles.

These discs have a harder abrasive than standard flap sanding discs.

The backing plate on these discs can be sheared away as the abrasive flaps wear down, allowing you to use more of the disc rather than replacing with a new one.

A coating prevents dust and debris from building up on the abrasive surface.

A special fastener on the back of these discs allows you to easily swap one disc for another.

These discs have a harder abrasive than standard quick-change discs.

The outer 3/8" of these discs is extremely flexible to prevent marring or gouging your work when sanding a radius or contour.

Debur, clean, and blend faster than other nylon mesh discs.

The abrasive-embedded nylon mesh construction gives you more control over sanding pressure.

Used for heavy cleaning and stripping, these discs have an abrasive-embedded nylon mesh construction that gives you more control over sanding pressure.

The heavy duty construction provides more support than standard discs for heavy material removal.

Fit these discs over your tool's arbor.

A coating prevents dust and debris from building up on the abrasive surface.

The abrasive-embedded mesh construction gives you more control over sanding pressure, creating finer and more consistent finishes.

The premium abrasive stays sharp longer.

The premium abrasive stays sharp longer.

The premium abrasive stays sharp longer. Holes in the disc let you see the surface you’re sanding.

Fit these discs over your tool's arbor to sand masonry, ceramics, and composites.

Press onto a compatible sanding tool or backup pad; peel off to remove.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

The premium abrasive stays sharp longer.

These discs have a long-lasting diamond abrasive.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

Made of foam, these discs can conform to contoured shapes, corners, and sharp edges.

The premium abrasive lasts longer as well as cuts faster and produces a more consistent finish than standard hook and loop discs.

Holes allow dust removal when used with a vacuum sander.

The mesh backing lets sanding dust and debris escape during use, preventing material build up on the abrasive surface.

Use with commercial floor buffing machines to sand wood floors and strip tape from concrete.

Made of foam, these blocks flex to sand around curves.

Secure the shank into the collet or chuck of your tool. Attach the quick-change fastener on the sanding disc to the corresponding fastener on the backup pad.

Thread these pads onto the tool’s arbor.

Thread one of these backup pads onto the tool’s arbor, then attach a sanding disc and secure with the disc nut.

Designed to rotate independently of the disc, these pads clear material buildup on the abrasive surface for longer disc life.

Mount one of these pads onto the tool's arbor.

Secure the shank into the collet or chuck of a tool.

Secure the shank into the collet or chuck of a tool.

Install cutoff wheels, grinding wheels, and other abrasive discs to the threaded shaft on bench-top motors, grinders, and buffers.

A titanium aluminum nitride (TiAlN) coating provides heat and wear resistance for longer life.

Reach around barriers to cut, grind, shape, and remove sharp edges in hard-to-access spots.

Pointed teeth cut wood and rubber quickly without clogging.

Diamond-cut teeth effectively cut hard materials.