Assortments include various sizes of inserts, a soldering iron, a ceramic insulation tube, and installation tips.

With the male threaded end on these inserts, mount components directly to plastic parts.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.

Made from brass, these inserts are nonmagnetic, corrosion resistant, and electrically conductive.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

70% lighter than stainless steel, these aluminum inserts are mildly corrosion resistant and nonmagnetic.

Push down on the inside of these inserts with an installation tool and they expand to hold firm in surrounding material.

These inserts are made to stringent military specifications.

The strongest key-locking inserts we offer, these inserts are made to stringent military specifications.

These inserts come with an installation tool. Drive the keys into the surrounding material for a more secure hold than thread-locking inserts.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

A dry film keeps the screw from sticking or binding in these inserts during installation.

Inserts come with a through-hole tap and installation tool.

Made of 18-8 stainless steel, these inserts have better corrosion resistance than black-phosphate steel.

A closed-end tap, drill bit, and installation bit are included with these inserts.

Large threads cut into softwood such as particleboard for a strong hold.

Made from brass, these inserts are nonmagnetic, mildly corrosion resistant, and electrically conductive.

These 18-8 stainless steel inserts have excellent resistance to chemicals and may be mildly magnetic.

These 18-8 stainless steel tee nut inserts have better corrosion resistance than zinc-plated steel tee nut inserts.

Fewer prongs than other tee nut inserts reduce the risk of splitting hardwood—these inserts have three short prongs.

An open end allows long screws and bolts to pass through the insert.

Mount these inserts flush or below the material's surface.

These nuts have good chemical resistance and may be mildly magnetic.

These press-fit nuts have a nylon insert that grips threads to resist loosening.

These press-fit nuts have a zinc plating for corrosion resistance in wet environments.

These press-fit nuts are tin plated to resist corrosion from chemicals and salt water.

The most corrosion resistant twist-resistant rivet nuts we offer, these stand up to chemicals.

Wedges under the flange lock the nut in place in soft materials such as brass and aluminum.

These kits include one size of low-profile rivet nuts.

The most corrosion resistant low-profile rivet nuts we offer, these stand up to chemicals.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

A PVC foam seal under the flange keeps liquids and gasses from leaking between the nut and the surrounding material.

Threads float inside the nut so you can install a screw at a slight angle to align with off-center parts. They’re also known as Riv-Float nuts.

Weld these nuts to stainless steel surfaces.

Projections on the base concentrate the weld and provide room for heat to dissipate.

These nuts can be used in channels and tight spaces where round-base weld nuts won't fit.

Weld these nuts to stainless steel surfaces.

Weld these nuts to flat and uneven uncoated steel surfaces for a strong permanent hold.

Threads float inside the retainer so you can install a bolt at a slight angle to align with off center parts.

Stainless steel adhesive-mount nuts have excellent corrosion resistance in most environments.

Create threads in hard-to-work areas—where you can’t reach the back of a workpiece, or material is too thin to be tapped.

Stronger than stainless steel, these nuts are comparable in strength to Grade 9 bolts.

Drive these tools with a hammer to expand anchors.

These steel studs are zinc plated to resist corrosion in wet environments.

Add a stud to thin material when you only have access to one side.

316 stainless steel studs have excellent resistance to chemicals and salt water.

Pass these studs through a hole and weld them in place.

Weld these studs to uncoated steel surfaces.

These include a barrel and a screw with an extra-wide (truss) head. Made from 316 stainless steel, they have excellent chemical resistance and can be used in saltwater environments.

One-third the weight of steel, aluminum binding barrels and screws resist corrosion in wet environments.

Brass binding barrels and screws are corrosion resistant in wet environments and electrically conductive.

Brass binding barrels and screws are corrosion resistant in wet environments and electrically conductive.

These binding barrels and screws have good chemical resistance.

A ribbed-shaped body holds the nut in place so it won't move when tightening a screw. Assortments contain rivet nuts, mandrels, nosepieces, and a plier-style installation tool.

Place the tip of these tools into an insert and strike them with a hammer to drive the keys into the material. They’re compatible with Keensert® inserts.

Screw an insert onto these tools and drive them a quarter to half-turn below the material's surface. They're compatible with helical inserts that have a prong.

Place the tip of these tools into an insert and strike a light blow to the tool’s head. Then turn the tools counterclockwise with pressure to extract the insert.

Thread these tools into an insert and turn counterclockwise to extract.

Compatible with Tap-Lok inserts.

These mounts have a cushion on top to provide padding between your furniture and the mount.

Twist these bumpers into a threaded hole. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces.

Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Mount these bumpers on a threaded stud.