Epoxies are the strongest and most weather- and chemical-resistant structural adhesives. They work especially well on metals.

For quick repairs, these epoxies begin to harden in 6 minutes or less.

To allow time to adjust and position parts, these epoxies remain workable for at least 90 minutes.

Bond most materials without the strong odor of other epoxy adhesives.

With excellent shear strength, these acrylics form bonds at least 25% stronger than standard acrylic structural adhesives.

Fasten hard-to-bond plastics, such as polypropylene and polyethylene, with these adhesives.

Also known as super glue, these adhesives bond quickly.

Mixed with rubber for better impact resistance than standard instant-bond adhesives, these adhesives form strong, resilient bonds.

Form bonds in 5 seconds or less.

In especially damp or humid environments, these adhesives keep their hold.

Use these thick gels, also known as super glue, on vertical surfaces or to fill gaps between parts.

These thick gels fill gaps up to 0.2" wide—the largest of any of our instant-bond adhesives.

For faster bonding, these adhesives begin to harden in half the time of our other wicking instant-bond adhesives.

To invisibly bond transparent plastics, these adhesives won’t turn cloudy.

For flexible bonds that resist cracking, these adhesives stay pliable.

To simultaneously mix and dispense two-part adhesives, attach these mixer nozzles to a dual cartridge.

Use these dispensing guns with Loctite® single-component syringes.

Prevent threaded fasteners from loosening due to shock and vibration.

Use these threadlockers on fasteners that require occasional fine-tuning, such as set screws.

Specially formulated for plastics, these threadlockers secure nylon, PTFE, and other plastic threaded fasteners.

These threadlockers develop usable strength within one hour. Because they harden quickly on most metals, they don't require a primer.

Paste threadlockers are easy to apply and won't drip, even from overhead fasteners.

This gel clings to fasteners to prevent drips.

Apply these threadlockers on fasteners that are already installed—their thin consistency allows them to flow into small gaps.

Improve instant-bond adhesive performance on hard-to-bond materials.

Shorten the time it takes instant-bond adhesives to reach full strength.

Fill gaps up to 0.01" to secure unthreaded cylindrical metal parts such as shafts, bearings, and press-fit assemblies.

Fill gaps up to 0.02" to secure worn unthreaded cylindrical metal parts such as shafts, bearings, and press-fit assemblies.

Wind this multifilament cord into the grooves of tapered pipe threads to quickly create a seal.

Apply this thread sealant stick without a mess.

Often used in high-vibration applications that could cause standard thread sealants to fail, these never fully harden and remain pliable enough to self-heal and stop leaks before they start.

Formulated for high lubricity, these sealants allow easy assembly of finely threaded hydraulic and compressed air system components. They're also free of fillers that could contaminate system media.

Made from silicone, these sealants are RTV (room-temperature vulcanizing).

Also known as neutral-cure sealants, these won't discolor copper, brass, and concrete.

The strongest of the potting compounds, epoxies are rigid and wear resistant. They have excellent chemical and moisture resistance, withstand a wide range of temperatures, and provide excellent electrical insulation.

No mixing required—these potting compounds come ready to apply.

Urethanes withstand a wide range of temperatures and are the best choice for cold-temperature applications. They have excellent flexibility, good chemical and moisture resistance, and provide good electrical insulation.

Thinner than potting compounds, these rigid and wear-resistant coatings flow easily into small spaces between electrical components. Use them to secure and insulate hardware on printed circuit boards.

This coating is formulated for use in sensitive applications such as manufacturing semiconductors.

Also known as brushable ceramic, these coatings create a hard, low-friction surface. They're often used on liquid processing equipment to protect worn areas and reduce turbulence.

These gasket makers come in a tube.

Push the plunger to precisely dispense small amounts.

All the benefits of a gasket maker in a no-drip form.

Use cartridges with a standard caulk gun for quick and easy dispensing.

Dispense a uniform bead when you press the nozzle.

Use cartridges with a standard caulk gun for quick and easy dispensing.

These gasket makers come in a tube.

Dispense a uniform bead when you press the nozzle.

These adhesives come in a can.

Form bonds that will not degrade in the presence of oils and fuels.

Create flexible seals that never fully harden.

Mix these two-part surface fillers together to repair leaks and cracks as well as to rebuild rough spots in metal.

For use in processing equipment that carries small particles less than 1/16" in diameter, these ceramic-filled epoxies rebuild and repair surfaces exposed to abrasion from particles, such as dust collectors, fan blades, and fan housings.

Repair and rebuild metal surfaces that are exposed to heat. These surface fillers withstand temperatures over 450° F.

A high silver content allows these surface fillers to conduct electricity and heat. Use them to fill gaps and rebuild missing material on electrical connections or to assemble new components.

These surface fillers can be used on vertical surfaces without sagging. They repair cracked, worn, and damaged surfaces.

Mix these two-part epoxy surface fillers to create a strong repair in wet environments or underwater.

This fast-lapping paste abrades quickly to produce a level, scratch-free surface.