Pull the trigger on these oilers for easier one-hand operation than standard hand-held oil dispensers.

Use suction to remove old lubricant from gear boxes and transmissions.

Mount these reservoirs directly to your machine, or use them with a flow-adjustment valve and brush to create a dispenser.

A sealed design prevents contamination in dirty and dusty environments. Install a line between the reservoir's pressure port and the lubricated equipment to balance pressure.

Thread these dispensers directly into bearing housings, pumps, and other machinery. Flip the lever to start and stop flow; turn the dial to adjust flow.

A sealed design prevents contamination in dirty and dusty environments.

Customize these dispensers to serve up to 24 lubrication points from a single location.

Control the flow of oil to a single lubrication point.

As chain, gears, and conveyors move, these brushes rotate to apply lubricant.

For use in clean environments, these manifolds have multiple air vents that keep pressure balanced.

Manually adjust the flow of oil to a single lubrication point.

A solenoid automatically starts and stops flow to a single lubrication point to dispense lubricant while equipment is running.

As chain, gears, and conveyors move, these brushes rotate to apply lubricant.

Dispense a fixed amount of oil by pumping the handle.

Choose from pumps that dispense with a set interval. Turn the dial to adjust the flow from 0.1 oz. to 0.2 oz. per cycle.

Connect these modular pumps to a reservoir and a solenoid valve to automate the flow of oil.

Air pressurizes the oil in the reservoir and atomizes the spray. Add a spray valve to direct the flow of oil.

Equipped with a flowmeter/totalizer, this dispenser displays both the flow rate and the cumulative flow volume of the oil dispensed.

Add faucets to oil dispensing stations for increased utility.

Driven by an air-powered pump, this dispenser comes with an adapter to mount through a bung opening on a drum.

Dispensing more grease per pump than pistol-grip guns, lever-grip guns are better for applications that require high grease output.

Spray thin liquids evenly with just one hand. These compact sprayers don’t need propellant—fill them and pressurize with air.

Drive these fittings into unthreaded holes.

Transfer hot oil up to 650° F in demanding applications such as plastic mold injecting and chemical processing.

Also known as proportional V-ball valves, these have a motor that adjusts and regulates flow in applications with higher flow rates and pressures than solenoid valves. As you increase the intensity of the electrical signal, the motor opens the valve, moving a ball with a V-cut opening that proportionately allows more flow as the valve opens. They're often integrated into PLC systems for automatic control over the valve position based on system conditions.

Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection. These valves are for use with water, oil, air, inert gas, and steam. They gradually open and close to adjust and regulate flow.

For a lightweight and corrosion-resistant alternative to metal valves, these have a plastic body. To create a permanent, leak-tight connection, insert unthreaded pipe into the socket ends and bond with PVC primer and cement. These valves are for use with oil. They gradually open and close to adjust and regulate flow.

Valves are for use with water, oil, air, inert gas, and steam. They gradually open and close to adjust and regulate flow.

Attach garden hose to the valve outlet. Use with water. These valves gradually open and close to adjust and regulate flow.

These valves are for use with water, oil, air, and inert gas. They bolt to flanges to adjust and regulate flow in flanged pipelines.

Often used in low-pressure water pipelines, these valves have a plastic body for the lightest weight of our flanged flow-adjustment valves. Use them with water. They bolt to flanges to adjust and regulate flow in flanged pipelines.

Often attached to differential pressure gauges to measure liquid level in tanks, these manifolds have two isolation valves with a pressure-equalizing valve between them. To isolate your differential pressure gauge for maintenance or calibration, shut off flow on both sides and equalize pressure in the manifold. They are rated for at least 6,000 psi. Use with water, oil, air, and inert gas.

Also known as block and bleed valves, these have two vent ports to isolate pressure gauges, switches, and other components in high-pressure systems for maintenance, calibration, and sampling without interrupting the process. They are rated for up to 10,000 psi. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

With a gauge port on each side of these valves, you can install two different pieces of instrumentation equipment to simultaneously monitor multiple media properties without interrupting flow. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Rated for nearly twice the maximum temperature of standard threaded precision flow-adjustment valves, these can handle up to 700° F. They’re for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

To ensure highly precise flow adjustment, these valves adjust flow in smaller increments than other valves for finer control over the flow rate in metering and sampling applications. Use them with water, oil, air, and inert gas.

Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Solder these valves to tubing for a permanent, leak-tight connection. Use them with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Use these valves with NPT threaded pipe. They have a fluoroelastomer seal and a plastic body to withstand aggressive and corrosive solutions in chemical-processing applications. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. The 316 stainless steel body and seal, the PTFE seat and packing, and the Monel needle can withstand aggressive and corrosive solutions in chemical-processing applications. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.