Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

The small-diameter shaft can access screws in narrow recessed holes.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

The toughest bits available, these withstand the shock and twisting force of impact drivers.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

When you don't have exact alignment between the fastener and the bit, the ball end allows angled entry to turn screws in hard-to-reach areas. A retaining ring grips inside the recess to hold screws in place.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

Ribs forged into the wings of these bits grip the screw recess to reduce stripping. They're also known as ACR® bits.

Drive screws with both ends of these bits. Use with hand drivers.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

Remove screws in hard-to-reach places. A spring-loaded sleeve guides bits onto the screw head and keeps them from slipping out.

Strong and durable, these multipurpose bits are often used with power tools to install sheet metal screws.

The toughest bits available, these withstand the shock and twisting force of impact drivers.

The slightly tapered tip wedges into the screw recess for a secure hold. Also known as Torx-Align bits.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

Turn two drive styles with one reversible bit. Remove and replace to change the tip.

The toughest bits available, these withstand the shock and twisting force of impact drivers. Designed for screws with a square recess in the head, they are also known as Robertson bits.

Bits have a different size at each end.

These bits provide a secure grip on the Phillips/slotted combination-drive screws in electrical equipment.

A three-winged tip fits triangular slotted screw recesses.

Strong and durable, these multipurpose bits are for use with bit screwdrivers.

These are also known as known as butterfly and Type G bits.

An opening at the tip accommodates the pin in the recess of tamper-resistant Torx screws. These are also known as pin-in-Torx bits.

The six rounded points fit the star-shaped recess of Torx-Plus screws. These bits have a similar profile to Torx but are not recommended for use with standard Torx screws.

Ribs forged into the wings of these offset-cross-shaped bits grip the screw recess to reduce stripping. They are also known as ACR® bits.

These are also known as TP3® bits.

Also known as Polydrive bits.

While screws with a Square/Phillips combination drive can be turned with either a Square or Phillips bit, these make the best contact so you can apply high torque without slipping and stripping the recess. They are also known as Quadrex bits.

Also known as Reed and Prince bits.

An opening at the tip accommodates the pin in the recess of tamper-resistant Phillips screws. These are also known as pin-in-head Phillips bits.

These bits are shaped like a 12-pointed star. They're also known as XZN bits.

Because they make contact on the flat sides of fasteners rather than only on the corners, these magnetic bits significantly reduce slipping and stripping. They’re also known as lobular bits.

Turn hex nuts and cap screws.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

The knurled shank on these bits allows finger tightening. They can also be used with the included screwdriver.

A retaining ring grips inside the recess to hold screws in place. These bits have a ball end that allows angled entry to drive screws in hard-to-reach areas.

Ribs forged into the wings of these bits grip the screw recess to reduce stripping. They're also known as ACR® bits.

These bits are also known as nut setters.

An opening at the tip accommodates the pin in the recess of tamper-resistant Torx screws. These are also known as pin-in-Torx bits.

Also known as Bristol bits, these have a knurled-end shank that allows finger tightening. They can also be used with the included screwdriver.

A three-winged tip fits triangular slotted screw recesses.

Use with screws that have two drilled holes.

These bits have an offset cross shape.

Lock your bit into the adapter to prevent accidental disengagement. These adapters hold hex-shank bits (also known as insert bits) in powered tools.

Keep bits from slipping. Insert a bit into the adapter, place a screw on the end of the bit, and slide the adapter sleeve over the screw. The sleeve retracts as the screw is driven. These adapters hold hex-shank bits (also known as insert bits) in powered tools.

Bend these adapters up to 90° to access hard-to-reach fasteners. Use them to hold hex-shank bits (also known as insert bits) in powered tools.

Attach these adapters to square-drive tools.

These adapters are designed to withstand the high torque of impact drivers. They hold hex-shank bits (also known as insert bits).

Insert these adapters into your SDS-drive rotary hammer to use it with hex-shank bits (also known as insert bits).

Mount the magnetic base to walls, cabinets, and other steel surfaces.

Fit these small cases comfortably in your pocket.

Lock the bit into the chuck to prevent accidental disengagement.

Bits are held in place with a retaining ring or set screw rather than a magnet, so the tool won't attract loose metal parts and shavings.

Drive screws four times faster than ratcheting alone. Grip the speed housing at the base of the shaft with one hand while turning the handle with the other. A magnet at the end of the shaft holds bits in place.

LEDs light the tip so you can use these tools in dark areas.

Also known as ESD-safe bit screwdrivers, the handle drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment.

A scaled-down version of standard changeable-shaft screwdrivers, these tools are shorter, slimmer, and easy to take with you. Remove and replace the shaft to use a different tip size.

An insulated handle and shafts protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900.

Bits have a different tip at each end and snap into the shaft, which is also a nutdriver.

Set includes a handle and six shafts. Remove and replace the shaft to use a different size or drive style.

Choose a handle based on torque and change shafts to use a different size or drive style. Factory-set screwdrivers ensure you reach the same torque every time.

These assorted shafts attach to a handle or can be used with socket wrenches and power tools. They have a ball end that allows angled entry to make good contact with the recess when a standard-tip shaft can’t.

Use these tools with 1/4" hex shank screwdriver bits. The rotating end cap on the handle allows you to apply constant pressure with your palm while turning the body of the driver with your fingertips.

The short bit on these sockets fits in spaces where height clearance is limited.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

These sockets are also known as Robertson bits.

These sockets are also known as pin-in-Torx bits.

Extra-long bits allow access to hard-to-reach fasteners.

The short bit on these sockets fits in spaces where height clearance is limited.

These sockets are also known as pin-in-Torx bits.

Use these sockets as an alternative to a screwdriver or L-key. They are made to withstand the high torque and force of impact tools.