Shaft End Supports | McMaster-Carr

Made with two pieces, these shaft supports secure your shaft parallel to your mounting surface and make it easy to access the shaft without having to slide it out or uninstall the support. Use these supports when working with light to medium loads where shaft alignment is not critical. These supports are machined to have flat, square surfaces, so they can be used to align other supports and parts in your system. Tighten the included clamping screws to secure the shaft.

Tee

Image of Product. Front orientation. Contains Annotated. Linear Shaft Supports. Easy-Access Base-Mount Linear Shaft Supports, Tee.

Tee supports have mounting flanges on the side. Mount these supports to a surface from either the top or bottom using the unthreaded holes.

Anodized 6061 Aluminum—Aluminum supports are lightweight and resist corrosion.

		Overall					Mounting Hole
	For Shaft Dia.	Lg.	Wd.	Ht.	Ctr. Ht.	Ctr. Ht. Tolerance	No. of	Ctr.-to-Ctr.	Dia.	Clamping Screw Thread Size	Fabrication		Each
Black Anodized 6061 Aluminum



		1/4"	1 1/2"	1/2"	1"	11/16"	-0.002" to 0"	2	1 1/8"	0.16"	6-32	Machined	00000000	000000


		3/8"	1 5/8"	9/16"	1 1/8"	3/4"	-0.002" to 0"	2	1 1/4"	0.16"	6-32	Machined	00000000	00000
		1/2"	2"	5/8"	1 1/2"	1"	-0.002" to 0"	2	1 1/2"	0.19"	8-32	Machined	00000000	00000
		5/8"	2 1/2"	11/16"	1 1/2"	1"	-0.002" to 0"	2	1 7/8"	0.22"	10-24	Machined	0000000	00000
		3/4"	2 3/4"	3/4"	1 13/16"	1 1/4"	-0.002" to 0"	2	2"	0.22"	10-24	Machined	00000000	00000
		1"	3 1/4"	1"	2 3/16"	1 1/2"	-0.002" to 0"	2	2 1/2"	0.28"	1/4"-20	Machined	00000000	00000
		1 1/4"	4"	1 1/8"	2 5/8"	1 3/4"	-0.002" to 0"	2	3"	0.34"	5/16"-18	Machined	00000000	00000
		1 1/2"	4 3/4"	1 1/4"	3"	2"	-0.002" to 0"	2	3 1/2"	0.34"	5/16"-18	Machined	00000000	00000
		2"	6"	1 1/2"	3 3/4"	2 1/2"	-0.002" to 0"	2	4 1/2"	0.41"	3/8"-16	Machined	00000000	00000
		8 mm	32 mm	10 mm	23 mm	15 mm	-0.05 mm to 0 mm	2	25 mm	4.5 mm	M2.5	Machined	00000000	00000
		12 mm	40 mm	12 mm	30 mm	20 mm	-0.05 mm to 0 mm	2	32 mm	5.5 mm	M3	Machined	00000000	00000


		16 mm	50 mm	16 mm	38 mm	25 mm	-0.05 mm to 0 mm	2	40 mm	5.5 mm	M4	Machined	00000000	00000
		20 mm	60 mm	20 mm	45 mm	30 mm	-0.05 mm to 0 mm	2	45 mm	5.5 mm	M5	Machined	00000000	00000
		25 mm	74 mm	25 mm	55 mm	35 mm	-0.05 mm to 0 mm	2	60 mm	6.6 mm	M6	Machined	0000000	00000
		30 mm	84 mm	28 mm	63 mm	40 mm	-0.05 mm to 0 mm	2	68 mm	9 mm	M8	Machined	00000000	00000
		40 mm	108 mm	32 mm	80 mm	50 mm	-0.05 mm to 0 mm	2	86 mm	11 mm	M10	Machined	00000000	00000

Low-Profile Tee

Low-profile tee supports are shorter and narrower than standard tee supports, so they are good for tight spaces. Mount these supports to a surface from either the top or bottom using the unthreaded holes.

304 Stainless Steel—Stainless steel supports resist corrosion better than aluminum supports.

Anodized 6061 Aluminum—Aluminum supports are lightweight and resist corrosion.

		Overall					Mounting Hole
	For Shaft Dia.	Lg.	Wd.	Ht.	Ctr. Ht.	Ctr. Ht. Tolerance	No. of	Ctr.-to-Ctr.	Dia.	Clamping Screw Thread Size	Fabrication		Each
304 Stainless Steel



		1/4"	1 5/8"	3/8"	7/8"	9/16"	-0.002" to 0"	2	1 1/4"	0.16"	6-32	Machined	0000000	000000


		3/8"	1 3/4"	3/8"	1"	5/8"	-0.002" to 0"	2	1 3/8"	0.16"	6-32	Machined	0000000	00000
		1/2"	2"	1/2"	1 3/16"	3/4"	-0.002" to 0"	2	1 5/8"	0.19"	8-32	Machined	0000000	00000
		5/8"	2 5/8"	1/2"	1 7/16"	15/16"	-0.002" to 0"	2	2 1/8"	0.22"	10-24	Machined	0000000	00000
		3/4"	2 3/4"	1/2"	1 9/16"	1"	-0.002" to 0"	2	2 1/4"	0.22"	10-24	Machined	0000000	000000
		1"	3 3/16"	3/4"	1 15/16"	1 1/4"	-0.002" to 0"	2	2 5/8"	0.28"	1/4"-20	Machined	0000000	000000
		1 1/4"	3 3/4"	3/4"	2 5/16"	1 1/2"	-0.002" to 0"	2	3 1/8"	0.34"	5/16"-18	Machined	0000000	000000
		1 1/2"	4"	3/4"	2 11/16"	1 3/4"	-0.002" to 0"	2	3 3/8"	0.34"	5/16"-18	Machined	0000000	000000
		2"	5"	1 1/4"	3 5/16"	2 1/8"	-0.002" to 0"	2	4 1/4"	0.41"	3/8"-16	Machined	0000000	000000
		8 mm	44 mm	10 mm	21 mm	12 mm	-0.05 mm to 0 mm	2	35 mm	4.5 mm	M4	Machined	000000	00000
		10 mm	46 mm	12 mm	25 mm	14 mm	-0.05 mm to 0 mm	2	38 mm	4.5 mm	M4	Machined	0000000	00000


		12 mm	48 mm	12 mm	25 mm	14 mm	-0.05 mm to 0 mm	2	40 mm	4.5 mm	M4	Machined	0000000	00000
		16 mm	62 mm	13 mm	31 mm	18 mm	-0.05 mm to 0 mm	2	50 mm	5.5 mm	M5	Machined	0000000	00000
		20 mm	65 mm	13 mm	36 mm	22 mm	-0.05 mm to 0 mm	2	54 mm	5.5 mm	M5	Machined	0000000	00000
		25 mm	80 mm	19 mm	44 mm	27 mm	-0.05 mm to 0 mm	2	66 mm	6.6 mm	M6	Machined	0000000	000000
		30 mm	96 mm	19 mm	52 mm	32 mm	-0.05 mm to 0 mm	2	78 mm	9 mm	M8	Machined	0000000	000000
		40 mm	108 mm	19 mm	66 mm	40 mm	-0.05 mm to 0 mm	2	90 mm	9 mm	M8	Machined	0000000	000000


		Anodized 6061 Aluminum



				1/8"	1 1/16"	5/16"	1/2"	5/16"	-0.002" to 0"	2	13/16"	0.14"	4-40	Machined	0000000	00000


				3/16"	1 3/16"	5/16"	9/16"	5/16"	-0.002" to 0"	2	15/16"	0.14"	4-40	Machined	0000000	00000
				1/4"	1 5/8"	3/8"	7/8"	9/16"	-0.002" to 0"	2	1 1/4"	0.16"	6-32	Machined	000000	00000
				3/8"	1 3/4"	3/8"	1"	5/8"	-0.002" to 0"	2	1 3/8"	0.16"	6-32	Machined	000000	00000
				1/2"	2"	1/2"	1 3/16"	3/4"	-0.002" to 0"	2	1 5/8"	0.19"	8-32	Machined	000000	00000
				5/8"	2 5/8"	1/2"	1 7/16"	15/16"	-0.002" to 0"	2	2 1/8"	0.22"	10-24	Machined	000000	00000
				3/4"	2 3/4"	1/2"	1 9/16"	1"	-0.002" to 0"	2	2 1/4"	0.22"	10-24	Machined	000000	00000
				1"	3 3/16"	3/4"	1 15/16"	1 1/4"	-0.002" to 0"	2	2 5/8"	0.28"	1/4"-20	Machined	000000	00000
				1 1/4"	3 3/4"	3/4"	2 5/16"	1 1/2"	-0.002" to 0"	2	3 1/8"	0.34"	5/16"-18	Machined	000000	00000
				1 1/2"	4"	3/4"	2 11/16"	1 3/4"	-0.002" to 0"	2	3 3/8"	0.34"	5/16"-18	Machined	000000	00000
				2"	5"	1 1/4"	3 5/16"	2 1/8"	-0.002" to 0"	2	4 1/4"	0.41"	3/8"-16	Machined	000000	00000


				3 mm	21 mm	6 mm	10 mm	6 mm	-0.05 mm to 0 mm	2	17 mm	2.4 mm	M2	Machined	0000000	00000
				4 mm	24 mm	6 mm	13 mm	7 mm	-0.05 mm to 0 mm	2	20 mm	2.4 mm	M2	Machined	0000000	00000
				5 mm	36 mm	8 mm	18 mm	10 mm	-0.05 mm to 0 mm	2	30 mm	3.4 mm	M3	Machined	0000000	00000
				6 mm	42 mm	10 mm	20 mm	11 mm	-0.05 mm to 0 mm	2	34 mm	4.5 mm	M4	Machined	0000000	00000
				8 mm	44 mm	10 mm	21 mm	12 mm	-0.05 mm to 0 mm	2	35 mm	4.5 mm	M4	Machined	0000000	00000
				10 mm	46 mm	12 mm	25 mm	14 mm	-0.05 mm to 0 mm	2	38 mm	4.5 mm	M4	Machined	0000000	00000
				12 mm	48 mm	12 mm	25 mm	14 mm	-0.05 mm to 0 mm	2	40 mm	4.5 mm	M4	Machined	0000000	00000
				16 mm	62 mm	13 mm	31 mm	18 mm	-0.05 mm to 0 mm	2	50 mm	5.5 mm	M5	Machined	00000000	00000
				20 mm	65 mm	14 mm	36 mm	22 mm	-0.05 mm to 0 mm	2	54 mm	5.5 mm	M5	Machined	0000000	00000
				25 mm	80 mm	19 mm	44 mm	27 mm	-0.05 mm to 0 mm	2	66 mm	6.6 mm	M6	Machined	00000000	00000


				30 mm	96 mm	19 mm	52 mm	32 mm	-0.05 mm to 0 mm	2	78 mm	9 mm	M8	Machined	00000000	00000
				35 mm	100 mm	19 mm	60 mm	34 mm	-0.05 mm to 0 mm	2	84 mm	9 mm	M8	Machined	00000000	00000
				40 mm	108 mm	19 mm	66 mm	40 mm	-0.05 mm to 0 mm	2	90 mm	9 mm	M8	Machined	00000000	00000
				50 mm	120 mm	25 mm	75 mm	45 mm	-0.05 mm to 0 mm	2	100 mm	9 mm	M8	Machined	00000000	00000

L-Shaped

L-shaped supports have a mounting flange on one face of the support. They are narrower than tee supports. Mount these supports to a surface from either the top or bottom using the unthreaded holes.

Anodized 6061 Aluminum—Aluminum supports are lightweight and resist corrosion.

			Overall					Mounting Hole
	For Shaft Dia.	Base Wd.	Lg.	Wd.	Ht.	Ctr. Ht.	Ctr. Ht. Tolerance	No. of	Ctr.-to-Ctr.	Dia.	Clamping Screw Thread Size	Fabrication		Each
Anodized 6061 Aluminum



		3/8"	9/16"	1"	15/16"	1"	5/8"	-0.002" to 0"	2	1/2"	0.18"	8-32	Machined	0000000	000000


		1/2"	11/16"	1 1/4"	1 3/16"	1 3/16"	3/4"	-0.002" to 0"	2	3/4"	0.2"	8-32	Machined	0000000	00000
		3/4"	11/16"	1 11/16"	1 3/16"	1 9/16"	1"	-0.002" to 0"	2	1"	0.27"	10-24	Machined	0000000	00000
		1"	11/16"	2"	1 7/16"	1 15/16"	1 1/4"	-0.002" to 0"	2	1 1/2"	0.27"	1/4"-20	Machined	0000000	00000
		10 mm	12 mm	28 mm	24 mm	25 mm	14 mm	-0.05 mm to 0 mm	2	16 mm	5 mm	M4	Machined	0000000	00000
		12 mm	12 mm	30 mm	24 mm	25 mm	14 mm	-0.05 mm to 0 mm	2	19 mm	5 mm	M4	Machined	0000000	00000
		20 mm	17 mm	43 mm	30 mm	36 mm	22 mm	-0.05 mm to 0 mm	2	29 mm	6 mm	M5	Machined	0000000	00000
		25 mm	17 mm	52 mm	36 mm	44 mm	27 mm	-0.05 mm to 0 mm	2	35 mm	7 mm	M6	Machined	0000000	00000

Rectangular

Rectangular supports do not have a mounting flange. They are the most compact support we offer. Mount these supports to a surface from the bottom using the tapped holes.

Anodized 6061 Aluminum—Aluminum supports are lightweight and resist corrosion.

		Overall					Mounting Hole
	For Shaft Dia.	Lg.	Wd.	Ht.	Ctr. Ht.	Ctr. Ht. Tolerance	No. of	Ctr.-to-Ctr.	Clamping Screw Thread Size	Fabrication	Mounting Thread Size		Each
Anodized 6061 Aluminum



		3/8"	1"	3/8"	1"	5/8"	-0.002" to 0"	2	11/16"	6-32	Machined	6-32	0000000	000000


		1/2"	1 1/4"	1/2"	1 3/16"	3/4"	-0.002" to 0"	2	13/16"	8-32	Machined	8-32	0000000	00000
		3/4"	1 11/16"	1/2"	1 9/16"	1"	-0.002" to 0"	2	1 3/16"	10-24	Machined	10-24	0000000	00000
		1"	2"	3/4"	1 15/16"	1 1/4"	-0.002" to 0"	2	1 1/2"	1/4"-20	Machined	1/4"-20	0000000	00000
		10 mm	30 mm	12 mm	25 mm	14 mm	-0.05 mm to 0 mm	2	18 mm	M4	Machined	M4 × 0.7 mm	0000000	00000
		12 mm	30 mm	12 mm	25 mm	14 mm	-0.05 mm to 0 mm	2	20 mm	M4	Machined	M4 × 0.7 mm	0000000	00000
		20 mm	42 mm	13 mm	36 mm	22 mm	-0.05 mm to 0 mm	2	30 mm	M5	Machined	M5 × 0.8 mm	0000000	00000
		25 mm	52 mm	19 mm	43 mm	27 mm	-0.05 mm to 0 mm	2	38 mm	M6	Machined	M6 × 1 mm	0000000	00000

Flange-Mount Linear Shaft Supports

These shaft supports hold linear shafts perpendicular to the mounting surface. They’re made of aluminum, which is lightweight and resists corrosion. Use them with light to medium loads where shaft alignment is not critical. Loosen the clamping screw to install, then tighten to secure.

Machined—Machined supports have flat, square surfaces, so they can be used to align other supports and parts in your system.

		Overall				Mounting Hole
	For Shaft Dia.	Lg.	Wd.	Ht.	Flange Thk.	No. of	Ctr.-to-Ctr.	Dia.	Clamping Screw Thread Size	Fabrication		Each
6061 Aluminum



		1/4"	1 1/2"	3/4"	1 1/2"	3/8"	4	1"	0.16"	6-32	Machined	00000000	000000


		3/8"	1 1/2"	3/4"	1 1/2"	3/8"	4	1"	0.16"	6-32	Machined	00000000	00000
		1/2"	1 5/8"	7/8"	1 5/8"	1/2"	4	1 1/4"	0.18"	8-32	Machined	00000000	00000
		5/8"	2"	7/8"	2"	1/2"	4	1 1/2"	0.18"	8-32	Machined	00000000	00000
		3/4"	2 3/8"	1"	2 3/8"	5/8"	4	1 3/4"	0.21"	10-32	Machined	00000000	00000
		1"	2 3/4"	1 1/4"	2 3/4"	5/8"	4	2 1/8"	0.27"	1/4"-20	Machined	00000000	00000
		1 1/4"	3 1/8"	1 3/8"	3 1/8"	3/4"	4	2 3/8"	0.27"	1/4"-20	Machined	00000000	00000
		1 1/2"	3 1/2"	1 5/8"	3 1/2"	3/4"	4	2 1/2"	0.33"	5/16"-18	Machined	00000000	000000
		2"	4"	2"	4"	7/8"	4	2 7/8"	0.33"	5/16"-18	Machined	00000000	000000


		1060 Aluminum



				10 mm	43 mm	10 mm	24 mm	5 mm	2	32 mm	5 mm	M4	Cast	00000000	00000


				12 mm	47 mm	13 mm	28 mm	7 mm	2	36 mm	5 mm	M4	Cast	00000000	00000
				16 mm	50 mm	16 mm	31 mm	8 mm	2	40 mm	5 mm	M4	Cast	00000000	00000
				20 mm	60 mm	20 mm	37 mm	8 mm	2	48 mm	7 mm	M5	Cast	00000000	00000
				25 mm	70 mm	25 mm	42 mm	10 mm	2	56 mm	7 mm	M5	Cast	00000000	00000
				30 mm	80 mm	30 mm	50 mm	12 mm	2	64 mm	9 mm	M6	Cast	00000000	00000
				35 mm	92 mm	35 mm	58 mm	14 mm	2	72 mm	12 mm	M8	Cast	00000000	00000
				40 mm	102 mm	40 mm	67 mm	16 mm	2	80 mm	12 mm	M10	Cast	00000000	00000

Base-Mount Linear Shaft Supports

For use with light to medium loads where shaft alignment is not critical, these shaft supports brace the end of a linear shaft along the ground or other flat surface. They are tees, so the mounting flanges are on the side. Mount the support to a surface from either the top or bottom using the unthreaded holes. Slide the shaft in to install, then tighten the included clamping screw to secure the shaft.

Tee

Image of Product. Front orientation. Contains Annotated. Linear Shaft Supports. Base-Mount Linear Shaft Supports.

6061 Aluminum—Aluminum supports are lightweight and corrosion resistant.

Iron—Iron shaft supports are heavier than aluminum shaft supports for a more stable mount.

Machined—Machined supports have flat, square surfaces, so they can be used to align other supports and parts in your system.

		Overall					Mounting Hole
	For Shaft Dia.	Lg.	Wd.	Ht.	Ctr. Ht.	Ctr. Ht. Tolerance	No. of	Ctr.-to-Ctr.	Dia.	Clamping Screw Thread Size	Fabrication		Each
6061 Aluminum



		1/4"	1 1/2"	1/2"	1 1/16"	11/16"	-0.002" to 0.002"	2	1 1/8"	0.16"	6-32	Machined	0000000	000000


		3/8"	1 5/8"	5/8"	1 3/16"	3/4"	-0.002" to 0.002"	2	1 1/4"	0.16"	6-32	Machined	0000000	00000


		Iron



				1/2"	2"	5/8"	1 5/8"	1"	-0.002" to 0.002"	2	1 1/2"	0.19"	8-32	Cast	0000000	00000


				5/8"	2 1/2"	11/16"	1 3/4"	1"	-0.002" to 0.002"	2	1 7/8"	0.22"	10-32	Cast	0000000	00000
				3/4"	2 3/4"	3/4"	2 1/8"	1 1/4"	-0.002" to 0.002"	2	2"	0.22"	10-32	Cast	0000000	00000
				1"	3 1/4"	1"	2 9/16"	1 1/2"	-0.002" to 0.002"	2	2 1/2"	0.28"	1/4"-20	Cast	0000000	00000
				1 1/4"	4"	1 1/8"	3"	1 3/4"	-0.002" to 0.002"	2	3"	0.34"	5/16"-18	Cast	0000000	00000
				1 1/2"	4 3/4"	1 1/4"	3 1/2"	2"	-0.002" to 0.002"	2	3 1/2"	0.34"	5/16"-18	Cast	0000000	00000
				2"	6"	1 1/2"	4 1/2"	2 1/2"	-0.002" to 0.002"	2	4 1/2"	0.41"	3/8"-16	Cast	0000000	00000


				1060 Aluminum



						8 mm	42 mm	14 mm	33 mm	20 mm	-0.02 mm to 0.02 mm	2	32 mm	6 mm	M4	Cast	00000000	00000


						10 mm	42 mm	14 mm	33 mm	20 mm	-0.02 mm to 0.02 mm	2	32 mm	6 mm	M4	Cast	00000000	00000
						12 mm	42 mm	14 mm	38 mm	23 mm	-0.02 mm to 0.02 mm	2	32 mm	6 mm	M4	Cast	00000000	00000
						16 mm	48 mm	16 mm	44 mm	27 mm	-0.02 mm to 0.02 mm	2	38 mm	6 mm	M4	Cast	00000000	00000
						20 mm	60 mm	20 mm	51 mm	31 mm	-0.02 mm to 0.02 mm	2	45 mm	7 mm	M5	Cast	00000000	00000
						25 mm	70 mm	24 mm	60 mm	35 mm	-0.02 mm to 0.02 mm	2	56 mm	7 mm	M6	Cast	00000000	00000
						30 mm	84 mm	28 mm	70 mm	42 mm	-0.02 mm to 0.02 mm	2	64 mm	9 mm	M6	Cast	00000000	00000
						35 mm	98 mm	32 mm	82 mm	50 mm	-0.02 mm to 0.02 mm	2	74 mm	11 mm	M8	Cast	00000000	00000
						40 mm	114 mm	36 mm	96 mm	60 mm	-0.02 mm to 0.02 mm	2	90 mm	11 mm	M8	Cast	00000000	00000

Easy-Access Flange-Mount Linear Shaft Supports

A removable collar allows access to the shaft without unbolting the flange. For use with light to medium loads where shaft alignment is not critical, these supports allow you to hold linear shafts perpendicular to the mounting surface. Secure the shaft by tightening the clamping screw. These supports are machined to have flat, square surfaces, so they can be used to align other supports and parts in your system.

304 Stainless Steel—Stainless steel supports resist corrosion better than aluminum supports.

Anodized 6061 Aluminum—Aluminum supports are lightweight and resist corrosion.

		Overall						Mounting Hole
	For Shaft Dia.	Dia.	Lg.	Wd.	Ht.	Flange Thk.	Bolt Circle Dia.	No. of	Ctr.-to-Ctr.	Dia.	Clamping Screw Thread Size	Fabrication		Each
1117 Carbon Steel



		1/4"	1 5/8"	—	3/4"	—	1/4"	1 11/32"	4	—	0.15"	6-32	Machined	000000	000000


		3/8"	1 5/8"	—	3/4"	—	1/4"	1 11/32"	4	—	0.15"	6-32	Machined	000000	00000
		1/2"	2 1/4"	—	1"	—	5/16"	1 3/4"	4	—	0.177"	8-32	Machined	000000	00000
		5/8"	2 5/8"	—	1"	—	5/16"	2 1/8"	4	—	0.201"	10-32	Machined	000000	00000
		3/4"	3"	—	1"	—	5/16"	2 3/8"	4	—	0.266"	1/4"-28	Machined	000000	00000
		1"	3 1/4"	—	1 5/8"	—	3/8"	2 3/4"	4	—	0.266"	1/4"-28	Machined	000000	000000
		1 1/4"	3 1/2"	—	1 5/8"	—	3/8"	3"	4	—	0.266"	1/4"-28	Machined	000000	000000
		1 1/2"	3 3/4"	—	2"	—	13/32"	3 1/4"	4	—	0.266"	1/4"-28	Machined	000000	000000
		2"	4 1/2"	—	2 3/8"	—	1/2"	3 7/8"	4	—	0.328"	5/16"-24	Machined	000000	000000


		304 Stainless Steel



				3/8"	—	1 7/16"	5/8"	1 7/16"	3/16"	—	4	1 1/8"	0.17"	6-32	Machined	0000000	00000


				1/2"	—	1 11/16"	3/4"	1 11/16"	1/4"	—	4	1 1/4"	0.2"	8-32	Machined	0000000	000000
				3/4"	—	2 3/16"	3/4"	2 3/16"	1/4"	—	4	1 3/4"	0.22"	10-24	Machined	0000000	000000
				1"	—	2 11/16"	1 1/16"	2 11/16"	5/16"	—	4	2 1/8"	0.28"	1/4"-20	Machined	0000000	000000
				10 mm	—	43 mm	19 mm	43 mm	6 mm	—	4	32 mm	4.8 mm	M4	Machined	0000000	000000
				12 mm	—	43 mm	19 mm	43 mm	6 mm	—	4	32 mm	4.8 mm	M4	Machined	0000000	000000
				20 mm	—	55 mm	20 mm	55 mm	6 mm	—	4	42 mm	5.8 mm	M5	Machined	0000000	000000
				25 mm	—	68 mm	28 mm	68 mm	8 mm	—	4	54 mm	7.1 mm	M6	Machined	0000000	000000


				Anodized 6061 Aluminum



						8 mm	—	36 mm	16 mm	36 mm	5 mm	—	4	28 mm	4.8 mm	M4	Machined	0000000	00000


						10 mm	—	43 mm	19 mm	43 mm	6 mm	—	4	32 mm	4.8 mm	M4	Machined	0000000	00000
						12 mm	—	43 mm	19 mm	43 mm	6 mm	—	4	32 mm	4.8 mm	M4	Machined	0000000	00000
						16 mm	—	55 mm	20 mm	55 mm	6 mm	—	4	42 mm	5.8 mm	M5	Machined	0000000	00000
						20 mm	—	55 mm	20 mm	55 mm	6 mm	—	4	42 mm	5.8 mm	M5	Machined	0000000	00000
						25 mm	—	68 mm	28 mm	68 mm	8 mm	—	4	54 mm	7.1 mm	M6	Machined	0000000	00000
						30 mm	—	87 mm	28 mm	87 mm	8 mm	—	4	64 mm	9.9 mm	M8	Machined	0000000	00000
						40 mm	—	100 mm	30 mm	100 mm	10 mm	—	4	75 mm	9.9 mm	M8	Machined	0000000	00000

End Supports for Ball Screws and Precision Lead Screws

A set of ball bearings reduces friction and secures the end of a ball or lead screw. Note: The end of your ball or lead screw must be machined before installing it into an end support.

For Radial Loads About For Radial Loads

Image of Product. Front orientation. Contains Annotated. End Supports for Ball Screws and Precision Lead Screws. For Radial Loads.

End supports for radial loads handle loads perpendicular to the lead screw.

							Face Mounting Holes			Top Mounting Holes
	ID	Ht.	Ctr. Ht.	Wd.	Dp.	No. of Mounting Holes	Dia.	Ctr.-to-Ctr. Wd.	Ctr.-to-Ctr. Ht.	Dia.	Ctr.-to-Ctr. Wd.	Temp. Range, ° F		Each
Alloy Steel



		23/64"	2"	1"	2 3/4"	35/64"	6	9/32"	2"	1 3/8"	9/32"	2"	-40 to 210	000000000	0000000


		15/32"	1 7/8"	1"	3"	25/32"	6	9/32"	2 1/4"	1 1/8"	13/32"	2 1/4"	-40 to 210	000000000	000000
		19/32"	2 1/8"	1 1/8"	3 1/2"	1 55/64"	6	9/32"	2 1/2"	1 3/8"	13/32"	2 1/2"	-40 to 210	000000000	000000
		25/32"	2 3/4"	1 7/16"	4 1/2"	1 7/64"	6	15/32"	3 1/4"	1 3/4"	21/32"	3 1/4"	-40 to 210	0000000	000000
		1 3/16"	3 5/8"	1 7/8"	6 1/2"	1 21/32"	6	21/32"	4 3/4"	2"	29/32"	4 3/4"	-40 to 210	000000000	000000

For Combined Radial and Thrust Loads About For Combined Radial and Thrust Loads

Image of Product. Front orientation. Contains Annotated. End Supports for Ball Screws and Precision Lead Screws. For Combined Radial and Thrust Loads.

End supports for combined radial and thrust loads handle radial loads (perpendicular to the lead screw) and thrust loads (parallel to the lead screw).

						Combined Load Cap., lbf			Face Mounting Holes			Top Mounting Holes
	ID	Ht.	Ctr. Ht.	Wd.	Dp.	Static	Dynamic	No. of Mounting Holes	Dia.	Ctr.-to-Ctr. Wd.	Ctr.-to-Ctr. Ht.	Dia.	Ctr.-to-Ctr. Wd.	Temp. Range, ° F		Each
Alloy Steel



		23/64"	2"	1"	2 3/4"	1 3/16"	1,000	440	6	9/32"	2"	1 3/8"	9/32"	2"	-40 to 210	00000000	0000000


		15/32"	1 7/8"	1"	3"	1 11/32"	1,600	630	6	9/32"	2 1/4"	1 1/8"	13/32"	2 1/4"	-40 to 210	00000000	000000
		19/32"	2 1/8"	1 1/8"	3 1/2"	1 1/2"	2,300	1,050	6	9/32"	2 1/2"	1 3/8"	13/32"	2 1/2"	-40 to 210	00000000	000000
		43/64"	2 3/8"	1 1/4"	4"	1 21/32"	3,200	1,550	6	13/32"	2 7/8"	1 3/8"	17/32"	2 7/8"	-40 to 210	000000000	000000
		25/32"	2 3/4"	1 7/16"	4 1/2"	1 7/8"	3,200	1,800	6	15/32"	3 1/4"	1 3/4"	21/32"	3 1/4"	-40 to 210	00000000	000000
		63/64"	3 3/8"	1 3/4"	6"	1 15/16"	3,750	2,100	6	21/32"	4 1/4"	2"	29/32"	4 1/4"	-40 to 210	00000000	00000000
		1 3/16"	3 5/8"	1 7/8"	6 1/2"	2 1/16"	5,200	3,050	6	21/32"	4 3/4"	2"	29/32"	4 3/4"	-40 to 210	00000000	00000000
		1 49/64"	5 5/8"	2 13/16"	8 1/2"	3 15/32"	15,000	9,000	10	13/16"	6 5/8"	3 5/8"	1 1/32"	6 5/8"	-40 to 210	00000000	00000000


		Carbon Steel



				12 mm	43 mm	25 mm	60 mm	34 mm	730	1,450	4	—	—	—	6.6 mm	46 mm	0 to 160	0000000	000000


				15 mm	48 mm	28 mm	70 mm	38 mm	890	1,700	4	—	—	—	6.6 mm	54 mm	0 to 160	0000000	000000
				17 mm	64 mm	39 mm	86 mm	51 mm	1,300	3,050	4	—	—	—	9 mm	68 mm	0 to 160	0000000	000000

Machinable Easy-Access Base-Mount Linear Shaft Supports

Create a support that fits the exact dimensions of your shaft to brace it along a flat surface. Good for use with square- and hex-profile shafts, these aluminum supports also work with round shafts of any diameter up to 1". Use them for light-to-medium-load linear motion applications where shaft alignment is not critical. These supports are tees, so the mounting flanges are on the side. Mount the support to a surface from either the top or bottom using the unthreaded holes. These supports are machined to have flat, square surfaces, so they can be used to align other supports and parts in your system.

Supports come with spacers between the two halves. For a snug fit, leave the spacers in place when machining, then remove before installing the shaft. Tighten the included clamping screws to secure the shaft.

Tee

Image of Product. Front orientation. Contains Annotated. Linear Shaft Supports. Machinable Easy-Access Base-Mount Linear Shaft Supports.

		Overall					Mounting Hole
	For Max. Shaft Dia.	Lg.	Wd.	Ht.	Ctr. Ht.	Ctr. Ht. Tolerance	No. of	Ctr.-to-Ctr.	Dia.	Clamping Screw Thread Size	Fabrication		Each
Black Anodized 6061 Aluminum



		1"	3 1/4"	1"	2 3/16"	1 1/2"	-0.002" to 0"	2	2 1/2"	0.28"	1/4"-20	Machined	0000000	000000

Low-Profile Tee

		Overall					Mounting Hole
	For Max. Shaft Dia.	Lg.	Wd.	Ht.	Ctr. Ht.	Ctr. Ht. Tolerance	No. of	Ctr.-to-Ctr.	Dia.	Clamping Screw Thread Size	Fabrication		Each
Anodized 6061 Aluminum



		1"	3 3/16"	3/4"	1 15/16"	1 1/4"	-0.002" to 0"	2	2 5/8"	0.28"	1/4"-20	Machined	0000000	000000