About Gears
More
High-Strength Corrosion-Resistant HTD Timing Belt Pulleys
Move belts forward and backward or stop and start them in precise positions, especially in areas where rust is a concern. The curved teeth on these high-torque drive (HTD) pulleys have more surface contact with belts than traditional trapezoidal teeth, which allows you to apply more torque without damaging belts. These teeth fit together seamlessly to prevent backlash, or unwanted movement of the belt on the pulley, for a smooth, quiet cycle. These pulleys are often used in 3D printing, machine tool drives, robotics, and other applications where precision is essential. They are also known as curvilinear belt pulleys.
Pair pulleys with an HTD timing belt that has the same pitch. The width of your belt should not be larger than the maximum belt width listed.
Aluminum pulleys will not rust in damp or humid environments, but water left on the surface will cause them to corrode.
![](/prerenderstable/mvPRE/contents/gfx/imagecache/649/6497k253-@halfx_pkc5o_1718211075.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/648/6486k325l1-d03b-digital-master1551973604-p9@halfx_636598986389830000.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/tbp/tbpulley-hubtwoflangel3-d03b-digital-master1551973625-p9@halfx_636598989053840000.png?ver=imagenotfound)
OD, mm | Number of Teeth | Pitch, mm | For Shaft Dia. | Bore Type | Inside Wd., mm | Outside Wd., mm | Overall Wd., mm | Pitch Dia., mm | Number of Flanges | Fabrication | Hub Dia., mm | Each | |
For 6 mm Max. Belt Wd. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
33.6 | 32 | 3 | 1/4" | Finished | 7.11 | 9.8 | 17.55 | 30.56 | 2 | Machined | 21.62 | 00000000 | 000000 |
For 9 mm Max. Belt Wd. | |||||||||||||
33.6 | 32 | 3 | 1/4" | Finished | 11.23 | 12.85 | 20.62 | 30.56 | 2 | Machined | 21.62 | 00000000 | 00000 |
Metal Gears and Gear Racks—20° Pressure Angle
The current industry standard, these 20° pressure angle gears have thicker, stronger teeth than 14½° pressure angle gears. Compared to plastic gears and racks, they’re better for high-load, high-speed, and heavy duty applications. Also known as spur gears.
Combine gears with different numbers of teeth to change speed and torque in your assembly. Combine a gear and rack to convert rotary motion into linear motion. To minimize your footprint, mount one or more standard gears inside of an internal gear.
For components to mesh correctly, they must have the same pressure angle and pitch/module.
Brass gears and racks are easy to machine, so you can add your own mounting holes and make other alterations. They won't rust when exposed to water.
Carbon steel components have hard, strong, and wear-resistant teeth, although they will rust when exposed to moisture and corrosive chemicals. They're best for high-torque machines, like lifting equipment, and heavy duty applications, such as rock crushing. Gears with teeth that are not hardened can be hardened to fit your application.
For technical drawings and 3-D models, click on a part number.
![](/prerenderstable/mvPRE/contents/gfx/imagecache/686/6867k54p1-d03b-digital@halfx_636977647692779610.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/ptg/ptgear-basicfront-d03b-digital-master1562184845-p9@halfx_636977651247968545.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/hub/hub-width--25e0a7017bf1599761117-p9@halfx_637353399229668263.png?ver=imagenotfound)
Metal Worms and Worm Gears
![](/prerenderstable/mvPRE/contents/gfx/imagecache/575/57545k411c1-d03b-digital@halfx_636977650538868349.png?ver=imagenotfound)
Worm gears use screw threads to make large reductions to shaft speed while transmitting motion at a right angle. They transmit motion from worm to gear and cannot be reversed. For gears and worms to mesh correctly, they must have the same pressure angle and pitch/module. These worms are compatible with plastic worm gears.
Speed ratio is the ratio by which output shaft speed is reduced. As speed decreases, torque increases.
Bronze gears have low friction and dissipate heat better than cast iron gears to provide a long service life for both the gear and the worm. They’re also more corrosion resistant than cast iron gears.
For technical drawings and 3-D models, click on a part number.
![](/prerenderstable/mvPRE/contents/gfx/imagecache/575/57545k411p1-d03b-digital@halfx_636977648405629945.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/ptg/ptgear-basicfront-d03b-digital-master1562184845-p9@halfx_636977651247968545.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/ptg/ptgear-basicsidel2-d03b-digital-master1562184847-p9@halfx_636977645886852404.png?ver=imagenotfound)
Hub | |||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Module | Speed Ratio | Number of Teeth | Pressure Angle | Gear Pitch Dia., mm | For Number of Thread Starts | OD, mm | Face Wd., mm | Overall Wd., mm | For Shaft Dia., mm | Dia., mm | Wd., mm | Material | For Thread Direction | Teeth Heat Treatment | Teeth Fabrication | Each | |
Round Bore—Bronze | |||||||||||||||||
0.8 | 40:1 | 40 | 20° | 32 | 1 | 33.6 | 9 | 18 | 6 | 20 | 9 | Bronze | Right Hand | Not Hardened | Not Ground | 000000000 | 000000 |
Plastic Gears and Gear Racks—20° Pressure Angle
The current industry standard, these 20° pressure angle gears have thicker, stronger teeth than 14½° pressure angle gears. Made of plastic, they run quieter than metal gears and have good corrosion and chemical resistance. They’re also known as spur gears.
Combine gears with different numbers of teeth to change speed and torque in your assembly. Combine a gear and rack to convert rotary motion into linear motion.
For components to mesh correctly, they must have the same pressure angle and pitch/module.
Acetal gears are best suited for use in light duty machines or for prototyping.
For technical drawings and 3-D models, click on a part number.
![](/prerenderstable/mvPRE/contents/gfx/imagecache/266/2662n314white-low-gloss-plasticpositive_front_negative_top_standard15_1592317652_612@halfx_637278964889769896.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/ptg/ptgear-basicfront-d03b-digital-master1562184845-p9@halfx_636977651247968545.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/hub/hub-width--25e0a7017bf1599761117-p9@halfx_637353399229668263.png?ver=imagenotfound)
Hub | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Module | Number of Teeth | Gear Pitch Dia., mm | OD, mm | Face Wd., mm | Overall Wd., mm | For Shaft Dia., mm | Material | Fabrication | Color | Dia., mm | Wd., mm | Each | |
Round Bore | |||||||||||||
0.8 | 40 | 32 | 33.6 | 4 | 9 | 6 | Acetal Plastic | Molded | White | 12 | 5 | 0000000 | 00000 |