We will reply to your message within an hour.
Insulate wire and cable splices, wrap wire harnesses, and repair cable jacketing with this stretchy tape.
Made with fiberglass for durability and abrasion resistance, this tape also withstands high temperatures.
Use this rubber tape to splice cable in high-voltage applications.
Also known as Scotchfil, this noncorrosive putty tape wraps, stretches, and molds around irregular shapes for insulation buildup.
This traditional black cotton electrician's tape provides an abrasion-resistant shield for wrapping low-voltage splices.
Apply this liquid for a skin-tight protective coating that insulates and resists moisture, acids, and corrosion.
No need for adhesive—this tape fuses to itself for a permanent seal and stretches to fit virtually any form. Also known as cold shrink tape.
This puncture- and cut-resistant cotton tape is coated with a high-grade electrical-insulating varnish. Also known as cambric tape.
This chemical-resistant tape has adhesive on both sides.
Also known as mastic tape, this tape is thicker than other electrical tape to cushion, insulate, and seal out moisture and environmental contaminants in electrical connections.
At only 0.0025" thick, this tape combines conformability with durability and abrasion resistance.
In the event of a fire, this rubber tape expands to protect cables from flames and heat.
Use this tape to modify printed circuit boards, shield components, and prototype wiring-board layout and design.
The adhesive on this conformable aluminum foil tape is electrically conductive for use on surfaces that can't be soldered. Use it to shield cables and electronic components from EMI (electromagnetic interference).
This polyester tape has a woven mesh edge that conducts electricity. Use it to shield cables and electronic components from EMI (electromagnetic interference).
Made of polyester fabric with a copper/nickel filler, this tape is highly conductive throughout, including the adhesive.
Twice as thick as our standard antistatic electrical tape, this tape is made of abrasion-resistant aramid and antistatic PTFE.
A coating on this polyimide tape minimizes ESD (electrostatic discharge) when unwound from the roll and also during removal.
Use this tape to attach components to heat sinks and metal chassis walls in place of screws and other mechanical fasteners. It conducts heat away from sensitive electronics.
Quickly conduct heat away from electronic components. Kapton® polyimide gives this tape excellent electrical isolation.
Reinforced with fiberglass, this tape is flexible yet resists tearing. Use it for sealing and patching insulation and duct.
Seal foil-jacketed insulation as well as air-conditioning and refrigeration systems with this conformable aluminum tape.
Seal fiberglass duct and insulation that's faced with an all-service jacket (ASJ). Tape is reinforced with fiberglass.
For easy identification, this tape is printed with flexible duct standard UL 181A-P or UL 181B-FX.
Stop water penetration with this tacky, flexible tape. It conforms to irregular shapes and expands to fill gaps. Use it on freezers, windows, and in marine applications.
An alternative to caulk and rubber sealants, this tape comes compressed and gradually expands to fill large gaps and voids.
Patch and seal roofs, window frames, gutters, and vents with this conformable tape.
Often used for weatherstripping and sealing gaps around windows, doors, and hatches; this tough tape keeps out moisture, dirt, heat, and cold.
Use this tape for a watertight bond on gutters, roofing membranes, and other building materials.
Often used to repair vinyl facings, this tape can be used on water heater blankets and fiberglass insulation joints.
It has the look of foil, but this polyethylene-coated cloth tape is more conformable so it won't twist or curl.
Use this tape outdoors for sealing and mounting signs and security control panels.
Prevent the spread of fire while sealing, cushioning, and damping vibration. This tape has adhesive on both sides.
Remove mounted objects from most surfaces without leaving residue behind.
The most conformable foam tape we offer, use this tape for mounting, gasketing, and damping sound and vibration. It has adhesive on both sides.
Tape is cut into convenient discs and rectangles.
Cut these sheets to the shape you need for a custom fit.
Mount lightweight signs and trim with this economical tape.
Used to mount panels, signs, and dispensers, this foam tape absorbs shock and provides high strength holding power on rigid surfaces.
The acrylic adhesive on this tape sticks to hard-to-bond materials, such as plastics and powder-coated surfaces.
This tape can withstand temperatures up to 300° F.
Use this clear tape for strong, invisible bonds.
Create strong, permanent bonds that can replace mechanical fasteners.
Cut these sheets to create a customized, permanent bond in the shape you need.
Use these clear shapes for strong, invisible bonds.
These foam discs and squares have extra-strong adhesive on both sides to create permanent bonds.
Use these clear sheets for strong, invisible bonds.
Foam damps vibration while securing lightweight objects, such as nameplates, dispensers, and smoke alarms. This tape has a tacky adhesive on one side and a permanent adhesive on the other.
Only 0.0019" thick, so spliced film and paper easily pass through machinery without breaking.
At half the thickness of our other masking tape for electronics, this polyimide tape conforms easily to components.
Use this tape to wrap and splice cables, mask components while soldering, or as a 3D printing surface.
Use these convenient cut shapes to mask holes, fastener heads, and small areas while soldering.
Aluminum foil is laminated to a tough fiberglass cloth to form a high-strength, reflective tape that resists temperatures up to 500° F. Use it for flame-spray masking and wire harness heat shielding.
In addition to handling temperatures up to 500° F, this fiberglass tape is tough enough for abrasive applications such as sand blasting.
Cover small spots and holes while paint stripping and electroplating, or use as a moisture and dust barrier. These aluminum foil discs are flexible and conform to irregular shapes.
This tape reflects intense heat to protect sensitive components.
Providing all-weather corrosion protection, this vinyl tape resists salt water, UV light, acids, and alkalies. Use it to wrap pipes and electrical conduit both above and below ground.
Made from stainless steel, this noncorrosive, nonstaining, and nonmagnetic tape bonds to metal. Patch scratched coatings and finishes to prevent corrosion in marine, food-processing, and nuclear applications.
Protect parts from radiation, X-rays, moisture, dust, and chemicals during electroplating and similar processes.
Quiet squeaky floor joists and reduce vibration with this foam tape.
Protect impact-prone surfaces from scratches, chips, and abrasion with this thick, conformable tape.
Easy to apply and remove, this film tape protects touch screens and other delicate parts during manufacturing and shipping.
Control the unwanted noise that comes from vibrating panels and support structures. This aluminum foil tape reduces vibration by converting it into a small amount of heat.
Our most slippery tape, the slick surface allows items to glide smoothly over it.
Also known as skived tape, this low-friction tape stretches to conform to irregular surfaces.
Backed with 3M VHB 4941 foam adhesive for strength, padding, and vibration resistance.
A strong, thick layer of Teflon® PTFE makes this tape tougher than standard Low-Friction Tape Made with Teflon® PTFE.
Low-Friction Tape Shapes Made with Teflon® PTFE.
This tape provides a slick surface along with excellent resistance to electrical current.
PEEK offers the best wear and abrasion resistance of our low-friction tapes. Use it for wire wraps and sliding bearing surfaces.
Highly resistant to impact, tearing, and corrosive chemicals, use FEP tape to line chutes and hoppers and to cover shelves in laboratories.
This tape discharges minor amounts of surface static electricity and resists static buildup.
Reduce noise and vibration in chutes, bins, and similar delivery systems with this UHMW-faced foam tape.
Fiberglass is laminated with Teflon® PTFE for a slippery, durable tape with excellent chemical and temperature resistance. Use it as a release surface on heat sealers and blister forming equipment.
Use this slippery PTFE-coated tape for a smooth release on heat sealers and molds.
Superior in strength and durability, these thin strips insulate as well as protect personnel from accidental contact with hot pipes. Use for exhaust, hot water, and process pipes.
Wrap pipes, tubing, and fittings to prevent condensation from forming. These strips are for use on copper, iron, and steel.
Protect and repair insulation with this cotton fiber and resin mesh.
EPDM is blended with neoprene and SBR to create a general-purpose foam that offers good resistance to water and wear.
These vinyl foam sheets and strips are so conformable that once they're compressed they won't fully spring back. Use them to fill gaps and seal uneven surfaces.
Made of EPDM foam, these sheets and strips have the best resistance to water, sunlight, and oxidation of all the foam we offer.
In addition to having good resistance to water, sunlight, and oxidation, these neoprene foam sheets and strips resist swelling when they come into contact with oil.
Because this natural rubber foam readily bounces back to shape after compression, it’s a good choice for repetitive sealing applications, such as on doors.
This premium silicone is the most resilient foam we offer. It is equivalent to Cohrlastic and is also known as Norseal and silicone sponge.
These sheets and strips will bounce back to shape, even after extended compression.
One layer of fiberglass fabric is sandwiched between layers of silicone foam giving these strips strength to handle high-stress applications, such as gasketing.
Silicone maintains its flexibility across a wide range of temperatures.
Seal and damp vibration around high-temperature food-service equipment with these silicone foam sheets and strips.
Even after exposure to sunlight, rain, and snow, these silicone foam strips remain flexible.
A thin layer of aluminized fiberglass on this silicone foam reflects heat to protect sensitive equipment.
Even after extended compression, these sheets and strips will bounce back to shape.
Prevent the spread of flames with these self-extinguishing silicone foam sheets and strips.
Offering excellent resistance to corrosive environments, these Viton® fluoroelastomer foam sheets and strips stand up to a wide variety of chemicals, fuels, and oils.
This foam meets UL fire extinguishing specifications. It's made from a blend of Buna-N, neoprene, and vinyl to offer offer good resistance to oil.
Made from a blend of Buna-N, neoprene, and vinyl, these foam strips have good resistance to oil.
Stick this flexible tape to the back of welding seams to contain spatter and prevent oxygen, water vapor, and other gases from weakening the weld.
For welding large gaps, these strips form a rigid mold for your weld.
Stick these gaskets around door and vent cutouts or replace worn seals to maintain your enclosure's NEMA rating.
Very soft and conformable, this expanded PTFE gasket tape compresses into an extremely thin profile. Use it to create a leak-resistant seal in tight-tolerance applications, such as on precision machinery.
Level dies, plates, presses, and other machine tools—this shim tape conforms to curves and uneven surfaces.