We will reply to your message within an hour.
The abrasive-embedded mesh construction gives you more control over sanding pressure, creating finer and more consistent finishes.
Slip a cap onto the head of a shank and sand small, recessed, and hard-to-reach areas.
Choose a bit with the same angle as your countersink to debur the inside of the hole.
Shape, debur, and sand edges and internal surfaces.
The premium abrasive stays sharp longer.
As the outer layer wears away, new abrasive is exposed.
Flexible flaps reduce gouging while producing a uniform finish on flat and curved surfaces. They provide more control than a standard sanding sleeve but are more aggressive than a traditional flap wheel. As the flaps wear, new abrasive is exposed.
A cushioned layer gives you more control over sanding pressure, creating finer and more consistent finishes. These rolls can be cut to length.
Sized for tight spaces, these small pads sand flat and curved surfaces. They have a flexible foam layer that gives you more control over sanding pressure, creating finer and more consistent finishes.
Evenly sand two surfaces at once.
The long sides are angled 75°.
Flexible enough to sand around curves and in corners, these sponges provide the comfort and control of a sanding block.
A coating prevents dust and debris from building up on the abrasive surface.
These sponges conform exceptionally well to small, contoured surfaces.
These sheets resist deterioriation when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding.
These cut-to-length rolls resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding.
The soft abrasive is good for fine hand-polishing of metal surfaces that require the smoothest finish possible after an abrasive sequence. Also known as crocus cloth.
The dental floss of abrasives, these cords slip into areas that other forms cannot. They're good for deburring and polishing small holes, narrow slots, keyways, and grooves.
A thicker, heavier construction than standard rolls withstands tough sanding.
The soft abrasive is good for fine hand-polishing of soft nonferrous metals. Also known as crocus cloth.
Create smooth finishes on wood.
These rolls can be cut to length.
Cut the length you need, then stick to your sanding tool. When it's time to change the sheet, peel it off.
Peel and stick to your sanding tool. When it’s time to change the sheet, peel it off.
Cut the length you need, then quickly attach, remove, and reuse.
Quickly attach, remove, and reuse.
Peel and stick to your file handle. When it’s time to change the sheet, peel it off.
Quickly attach, remove, and reuse these hook-and-loop sheets with triangular detail sanders.
Quickly attach, remove, and reuse these hook-and-loop sheets with pole sanders.
Dust and debris won't build up on the abrasive surface.
Thicker, more pliable, and less aggressive than standard nylon mesh quick-change discs, use these for finer sanding on curved surfaces.
Debur, clean, and blend faster than other nylon mesh discs.
The abrasive-embedded nylon mesh construction gives you more control over sanding pressure.
A special fastener on the back of these discs allows you to easily swap one disc for another.
These discs have a harder abrasive than standard quick-change discs.
The heavy duty construction provides more support than standard discs for heavy material removal.
These discs have a harder abrasive than standard flexible-edge quick-change discs.
The outer 3/8" of these discs is extremely flexible to prevent marring or gouging your work when sanding a radius or contour.
The thick, abrasive-embedded nylon mesh construction gives you maximum control over sanding pressure.
These discs are abrasive-embedded cloth with a cushioned layer.
Made of foam, these discs can conform to contoured shapes, corners, and sharp edges.
Quickly attach, remove, and reuse these discs with a compatible sanding tool or backup pad.
The premium abrasive lasts longer as well as cuts faster and produces a more consistent finish than standard hook and loop discs.
The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.
The mesh backing lets sanding dust and debris escape during use, preventing material build up on the abrasive surface.
Holes allow dust removal when used with a vacuum sander.
Secure the shank into the collet or chuck of your tool.
Press onto a compatible sanding tool or backup pad; peel off to remove.
Holes in the disc let you see the surface you’re sanding.
Fit these discs over your tool's arbor.
These discs have a harder abrasive than standard flap sanding discs for corners.
Set at an angle and widely spaced, the overlapping abrasive flaps reach into corners.
The backing plate on these discs can be sheared away as the abrasive flaps wear down, allowing you to use more of the disc rather than replacing with a new one.
A heavy duty backing plate provides more support than standard discs for heavy material removal.
The abrasive-embedded mesh construction gives you more control over sanding pressure, creating more consistent finishes.
With more flaps than standard discs, these last 30-40% longer.
These discs have a harder abrasive than standard flap sanding discs.
Overlapping abrasive flaps bonded to a backing plate provide consistent material removal and even finishes.
The backing cushions the abrasive to prevent gouging your work surface.
Finish and polish metals without producing dust.
The abrasive-embedded nylon mesh gives you maximum control over sanding pressure.
These belts resist deterioration when used with water or cutting fluids.
Multiple layers of abrasive arranged in a pattern create highly consistent finishes.
These belts have a cushioned layer.
The widely spaced grains prevent dust and debris from building up on the abrasive surface.
Use these narrow belts on hand-held sanding sticks.
These belts have a tear-resistant backing.
The abrasive in these blocks wears evenly to maintain a flat surface. They can be used to remove burrs from metal die fixtures and machine parts or to clean magnetic chucks.
Clean and condition wood surfaces, leaving a wax-free shine.