Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

Suitable for clean room use, these carriages and guide rails are made entirely of stainless steel.

These carriages and guide rails are steel.

Designed for use on horizontal surfaces, the contact angle of the ball bearings on the rail allows these carriages to last longer than other carriages.

These tiny carriages and guide rails are sized for electronic and other precision applications.

With a wide base and low-profile design, these carriages and guide rails stabilize moment (twisting) and off-center loads better than other carriages and rails. They're good for use in areas where multiple carriages or rails won't fit.

With fewer moving parts and no need for lubrication, sleeve bearing carriages perform better in dusty and wet environments than ball and roller bearing carriages. They're also better at handling impact and vibration.

With a wide base, these sleeve bearing carriages stabilize moment (twisting) and off-center loads better than standard carriages. Use in areas where multiple carriages or rails won't fit.

For applications with low clearance, these carriages protrude less than 5 mm above their rails.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

The square profile prevents loads from twisting and rotating.

These track roller carriages and guide rails are stainless steel for use in wet, corrosive environments.

Use these carriages and guide rails for light loads where precise movement is not required.

Needle-roller bearings give these track roller carriages higher load capacities than other track roller carriages.

V-shaped rollers and rails allow these carriages to operate well in dirty environments because the debris won't get trapped on the rail.

High-temperature PTFE-thickened grease enables these carriages to operate in temperatures up to 500° F, higher than any other carriage that we offer.

Nylon rollers and aluminum rails make these good for light duty applications.

Slides have a row of ball bearings on each side of the rail.

Create your own positioning table or telescoping slide. Sets include four rails, two roller bearing cages, and eight end stops.

A linear scale and micrometer-like hand wheel measure travel distance in increments of 0.001".

A thumb screw locks the slide to prevent movement in systems where vibration is present.

A thumb screw locks the slide to prevent movement in systems where vibration is present.

Three micrometer handles ensure accurate, repeatable positioning along three axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

To provide corrosion resistance in wet environments, this framing is galvanized.

In addition to being lightweight and strong, this plastic framing is nonconductive with good resistance to chemicals and salt water.

These rails have continuous T-slots for attaching fittings. Use this versatile framing to configure machine guards, enclosures, carts, and workstations.

Half the height and the same width as regular strut channel, this low-profile strut channel fits into tight spots and is compatible with many of the same brackets.

Run cable and tubing in the tightest spaces with channel that is one-quarter the height and one-half the width of regular strut channel.

Slide the strut channel into the tube for telescoping length adjustments.

This welded, one-piece strut channel combines two strut channels back-to-back.

Serrated grooves grip the lip of the channel.

In addition to serrated grooves for gripping the lip of the channel, these nuts have wings for easy positioning.

Connect two channels to create a stacked channel.

Insert these nuts into the long open side of strut channel and twist to secure. A built-in washer enables one-handed installation.

Push these nuts into place rather than threading them onto a fastener.

Quickly attach these nuts by twisting them closed at any point along a threaded rod.

Use with hex nuts to connect threaded rod.

Notches on these washers grip the channel to keep them in place.

Designed to wrap around the sides of strut channel, these brackets provide a stronger hold than other strut channel brackets.

Push these brackets into strut channel and tighten the included cam screws for a partially concealed connection.

Slip these hangers onto the lip of top-opening strut channel to attach chain, wire rope, pipe, and threaded rod.

A tab on the end of these shelf brackets fits inside the strut channel for extra stability.

Provide smooth motion between two pieces of strut channel.

Position two strut channels at a 30° to 60° angle, then tighten the bolt to secure.

Rails are drilled with consistently spaced holes for multiple mounting options that do not require machining. Use this steel bolt-together framing to build guards, tables, and racks.