Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.

Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.

Secure two pressurized hydraulic lines with a single clamp. Mount these clamps directly onto rails, no adhesive or welding required. They fit tightly around the lines to reduce vibration.

A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.

Avoid the hassle of welding with these adhesive-mount clamps—they use a high-strength adhesive to form a permanent bond with the mounting surface—no additional tools required. Once assembled, the clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration.

A cushion covering the clamp reduces vibration and wear from clamp edges. Clamps surround lines of pipe, tubing, and conduit completely while holding them close to the mounting surface.

Suspend and route flat-bottomed objects such as strut channel and small duct.

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.

These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.

All-stainless steel construction stands up to water and chemicals and won't rust or corrode.

Higher deflection ratings translate to greater vibration and shock isolation.

Higher deflection ratings translate to greater vibration and shock isolation than our other vibration-damping leveling mounts.

A two-piece design simplifies installation and requires less clearance than one-piece mounts.

Spring action provides significant isolation of vibration and noise.

Limit damage during moderate earthquakes.

The polyurethane base on these mounts resists solvents, gasoline, and oil, while the metal plate sustains heavy loads.

Made of neoprene rubber, these mounts are oil resistant, so they're good for use under generators, HVAC equipment, electric motors, pumps, and blowers.

Made of tightly layered stainless steel mesh, these mounts withstand temperatures up to 500° F.

A two-piece design makes these mounts easier to install than one-piece mounts.

These mounts withstand exposure to weather and resist oil, antifreeze, and other petroleum-based fluids.

An interlocking steel frame in these mounts prevents collapse, even if the rubber fails.

In addition to having a wider temperature range than our other ribbed vibration-damping grommets, these have excellent weather resistance.

In addition to having a wider temperature range than our other vibration-damping grommets, these have excellent weather resistance.

Ribbed bushings are more flexible than our smooth vibration-damping bushings, so they're easier to install.

In addition to having a wider temperature range than our other vibration-damping bushings, these have excellent weather resistance.

Use these in place of normal washers to damp vibration and cushion your joint.

Made of nitrile rubber, these pads have excellent resistance to oil and solvents.

Able to shoulder up to 1,500 psi per mounting point, nitrile pads can support heavy machinery.

Made of fiber-reinforced PVC, these pads endure exposure to corrosive chemicals, such as cleaning solvents, chlorine, and hydrochloric acid.

Reinforced with fabric so extreme compression won’t deform them, these pads protect surfaces from impact, dampen vibration and noise, and act as stable connection points. They’re commonly known as bearing pads.

Great for use outdoors, these durable pads are neoprene rubber, which withstands exposure to direct sunlight.

Place pads under equipment, such as drill presses, milling machines, saws, and air-conditioning units to minimize vibration and noise transmitted to and from machinery.

These feet are made of UHMW polyethylene plastic, so they won’t dry out and become brittle.

Adjust the swivels on these mounts to level equipment on uneven surfaces for protection during earthquakes.

Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Mount these bumpers on a threaded stud.

These bumpers withstand temperatures up to 300° F, which is at least twice as high as our other load rated bumpers. Use them in applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, these bumpers absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Mount them on a threaded stud.

Install these bumpers with screws. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces.

These bumpers are at a 90° angle to protect corners on equipment, walls, and docks from damage caused by carts, vehicles, and other moving objects. Install them with screws.

Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Twist these bumpers into a threaded hole.