System of Measurement System of Measurement |
|---|
|
Length Length | Show |
|---|
|
Length Length | Hide |
|---|
Plain Bearing Type Plain Bearing Type |
|---|
 | Sleeve |
Bearing Type Bearing Type |
|---|
| Plain |
Lubrication Lubrication |
|---|
|
For Load Direction For Load Direction |
|---|
 | Radial |
Dynamic Radial Load Capacity Dynamic RadialLoad Capacity |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
For Shaft Type For Shaft Type |
|---|
 | Round |
Maximum Temperature Maximum Temperature |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
Misalignment Capability Misalignment Capability |
|---|
|
Filler Material Filler Material |
|---|
|
Lubricant Lubricant |
|---|
|
Lubrication Method Lubrication Method |
|---|
|
About Plain Bearings
More
Panel-Mount Dry-Running Sleeve Bearings
Permanently and securely install these self-clinching bearings into panels, with no need for precision-bored holes or machined mounts. They’re often used in areas with tight space restrictions. Install them into sheet metal panels with an air-powered or hydraulic press. They’re not for use in plastic panels. These bearings are self-aligning to compensate for small amounts of shaft misalignment. Made of acetal plastic, they won’t warp or swell when exposed to water, so they’re good for use in washdown environments.
For technical drawings and 3-D models, click on a part number.
| Length | Spline OD | For Minimum Sheet Metal Thickness | Dynamic Radial Load Capacity | Misalignment Capability | Temperature Range, °F | Each | |
Acetal Plastic Bearings | |||||||
|---|---|---|---|---|---|---|---|
For 3/4" Shaft Diameter | |||||||
| 0.9" | 1.3" | 0.058" | 170 lbs. @ 60 rpm | 5° | -40° to 180° | 0000000 | 000000 |
High-Speed Panel-Mount Dry-Running Sleeve Bearings
Made of acetal and PTFE plastic, these panel-mount bearings handle speeds twice as fast as standard acetal bearings can. They’re self-lubricating, which reduces wear and prolongs their lifespan. These bearings are shaped for permanent and secure mounting on metal panels without precision-bored holes or machined mounts. They’re commonly used in areas with tight space restrictions. Install them with an air-powered or hydraulic press. These bearings will swivel to compensate for small amounts of shaft misalignment. They’re not for use in plastic panels.
For technical drawings and 3-D models, click on a part number.
| Length | Spline OD | For Minimum Sheet Metal Thickness | Dynamic Radial Load Capacity | Misalignment Capability | Temperature Range, °F | Each | |
PTFE-Filled Acetal Plastic Bearings | |||||||
|---|---|---|---|---|---|---|---|
For 3/4" Shaft Diameter | |||||||
| 0.9" | 1.3" | 0.058" | 400 lbs. @ 60 rpm | 5° | -40° to 180° | 0000000 | 000000 |
Panel-Mount Oil-Embedded Sleeve Bearings
Unlike other sleeve bearings, these do not need to be fully inserted into a housing. Their unique shape creates a permanent, secure hold in thin panels. Bearings swivel to accommodate up to 5° of shaft misalignment. On startup, friction causes the bronze to release a thin layer of oil on the bearing’s surface. Not for use with plastic panels.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| Lg. | Spline OD | For Min. Sheet Metal Thick. | Dynamic Radial Load Capacity | Misalignment Capability | Lubrication | Lubricant | Temperature Range, °F | Each | |
840 Bronze Bearings | |||||||||
|---|---|---|---|---|---|---|---|---|---|
For 7/8" Shaft Dia. | |||||||||
| 0.9" | 1.63" | 0.09" | 1,400 lbs. @ 60 rpm | 5° | Lubricated | SAE 45 Oil | -20° to 200° | 0000000 | 000000 |
For 1" Shaft Dia. | |||||||||
| 0.9" | 1.63" | 0.09" | 1,400 lbs. @ 60 rpm | 5° | Lubricated | SAE 45 Oil | -20° to 200° | 0000000 | 00000 |