About Gears
More
Timing Belt Idler Pulleys
Add these free-spinning pulleys to your timing belt setup to minimize vibration and keep belts from wearing out. The needle bearing at the center of these pulleys is lined with small, cylindrical rollers that reduce friction as they rotate. This bearing allows both the pulley and the shaft it’s mounted on to spin independently. Made from iron or steel, these pulleys are strong and wear-resistant. The black oxide coating protects the pulleys from corrosion in dry environments.
Trapezoidal teeth on the outside of the pulley fit into teeth inside your timing belt—select a pulley that matches your belt trade size. The maximum belt width should be the same size or larger than the width of your timing belt.
For technical drawings and 3-D models, click on a part number.
For Max. Belt Wd. | OD | Number of Teeth | Teeth Shape | For Shaft Dia. | Pitch | Dia. | Bore Type | Overall Wd. | Pitch Dia. | Fabrication | Material | Bearing Type | Hub Dia. | Each | |
For L Belt Trade Size | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1" | 2.6" | 22 | Trapezoidal | 1" | 0.375" | 2 19/32" | Plain | 1 1/8" | 2.626" | Machined | Black-Oxide Steel | Needle Roller | 1 3/4" | 0000000 | 000000 |
Metal Gears and Gear Racks—14 1/2° Pressure Angle
A former industry standard, 14½° pressure angle gears are often found on older machinery. Made of carbon steel, they have high strength and are better than plastic gears and gear racks for high-load, high-speed, and heavy duty applications.
Combine gears with different numbers of teeth to change speed and torque in your assembly. Combine a gear and rack to convert rotary motion into linear motion.
For components to mesh correctly, they must have the same pressure angle and pitch.
Gears with machinable bore have a large hub diameter so you can machine them to fit your shaft.
Gears with teeth that are not hardened can be hardened to fit your application. Hardening a gear's teeth increases its wear resistance.
For technical drawings and 3-D models, click on a part number.
Hub | Keyway | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Gear Pitch | Number of Teeth | Gear Pitch Dia. | OD | Face Wd. | Overall Wd. | For Shaft Dia. | Material | Teeth Heat Treatment | Dia. | Wd. | Wd. | Dp. | Set Screw Thread Size | Each | |
Round/Machinable Bore | |||||||||||||||
10 | 24 | 2.4" | 2.6" | 1" | 1.625" | 3/4"-1 1/4" | 1144 Carbon Steel | Not Hardened | 2.125" | 0.625" | __ | __ | __ | 0000000 | 000000 |
Keyed Bore with Set Screw | |||||||||||||||
10 | 24 | 2.4" | 2.6" | 1" | 1.625" | 3/4" | 1144 Carbon Steel | Not Hardened | 2.125" | 0.625" | 0.188" | 0.094" | 1/4"-20 | 0000000 | 000000 |
Metal Gears and Gear Racks—20° Pressure Angle
The current industry standard, these 20° pressure angle gears have thicker, stronger teeth than 14½° pressure angle gears. Compared to plastic gears and racks, they’re better for high-load, high-speed, and heavy duty applications. Also known as spur gears.
Combine gears with different numbers of teeth to change speed and torque in your assembly. Combine a gear and rack to convert rotary motion into linear motion. To minimize your footprint, mount one or more standard gears inside of an internal gear.
For components to mesh correctly, they must have the same pressure angle and pitch/module.
Carbon steel components have hard, strong, and wear-resistant teeth, although they will rust when exposed to moisture and corrosive chemicals. They're best for high-torque machines, like lifting equipment, and heavy duty applications, such as rock crushing. Gears with teeth that are not hardened can be hardened to fit your application.
For technical drawings and 3-D models, click on a part number.
Hub | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Gear Pitch | Number of Teeth | Gear Pitch Dia. | OD | Face Wd. | Overall Wd. | For Shaft Dia. | Material | Teeth Heat Treatment | Dia. | Wd. | Each | |
Round Bore | ||||||||||||
20 | 50 | 2 1/2" | 2.6" | 1/2" | 1" | 1/2" | 1117 Carbon Steel | Not Hardened | 1.62" | 0.5" | 0000000 | 000000 |