System of Measurement System of Measurement |
---|
|
OD OD | Show |
---|
|
OD OD | Hide |
---|
Component Component |
---|
|
Bore Type Bore Type |
---|
![]() | ![]() |
Machinable | Round |
Material Material |
---|
|
Mounting Distance Mounting Distance |
---|
|
For Maximum Shaft Diameter For Maximum Shaft Diameter |
---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
---|
Length Length |
---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
Teeth Heat Treatment Teeth Heat Treatment |
---|
|
About Gears
More
Quick-Grip Screw-Clamp Bushings

Also known as Trantorque bushings, these tighten with a twist of the collar nut—no screws needed. As you tighten the collar nut, the inner sleeve contracts onto the shaft and the outer sleeve expands to hold your sprocket, pulley, or gear.
For technical drawings and 3-D models, click on a part number.
Light Duty Sleeve Bushings

Reduce the ID of sprockets, pulleys, and gears in low-torque applications. Bushings have a hole for a set screw.
For technical drawings and 3-D models, click on a part number.
Self-Adjusting Spring Bushings

A toothed slot lets these bushings contract for insertion into the bore of your sprocket or pulley and then expand for a snug fit. Made of spring steel, they flex under stress and shock and can handle oscillating or slow rotational motion.
For technical drawings and 3-D models, click on a part number.
Metal Gears and Gear Racks—14 1/2° Pressure Angle
A former industry standard, 14½° pressure angle gears are often found on older machinery. Made of carbon steel, they have high strength and are better than plastic gears and gear racks for high-load, high-speed, and heavy duty applications.
Combine gears with different numbers of teeth to change speed and torque in your assembly. Combine a gear and rack to convert rotary motion into linear motion.
For components to mesh correctly, they must have the same pressure angle and pitch.
Gears with teeth that are not hardened can be hardened to fit your application. Hardening a gear's teeth increases its wear resistance.
For technical drawings and 3-D models, click on a part number.



Hub | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Gear Pitch | Number of Teeth | Gear Pitch Dia. | OD | Face Wd. | Overall Wd. | For Shaft Dia. | Material | Teeth Heat Treatment | Dia. | Wd. | Set Screw Thread Size | Each | |
Round Bore | |||||||||||||
24 | 16 | 0.666" | 0.75" | 1/4" | 0.563" | 5/16" | 1144 Carbon Steel | Not Hardened | 0.547" | 0.313" | __ | 0000000 | 000000 |
Round Bore with Set Screw | |||||||||||||
24 | 16 | 0.667" | 0.75" | 1/4" | 0.563" | 5/16" | 1035, 1045, or 1144 Carbon Steel | Not Hardened | 0.547" | 0.313" | 10-32 | 00000000 | 00000 |
Plastic Gears and Gear Racks—14 1/2° Pressure Angle
A former industry standard, 14½° pressure angle gears are often found on older machinery. Made of plastic, they run quieter than metal gears and have good corrosion and chemical resistance. They’re also known as spur gears.
Combine gears with different numbers of teeth to change speed and torque in your assembly. Combine a gear and rack to convert rotary motion into linear motion.
For components to mesh correctly, they must have the same pressure angle and pitch.
For technical drawings and 3-D models, click on a part number.

Round/Machinable
Bore

Hub | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Gear Pitch | Number of Teeth | Gear Pitch Dia. | OD | Face Wd. | Overall Wd. | For Shaft Dia. | Material | Fabrication | Color | Dia. | Wd. | Each | |
Round Bore | |||||||||||||
32 | 22 | 0.688" | 0.75" | 3/16" | 0.438" | 1/4" | Nylon Plastic | Molded | White | 0.563" | 0.25" | 00000000 | 00000 |
Metal Ratcheting Gears

Compared to plastic gears, these metal ratcheting gears are better for high-load, high-speed, and heavy duty applications. Used to prevent unwanted motion in jacks, tie downs, clutches, and winches, ratchet gears have sloped teeth that allow motion in one direction and prevent it in the other. Gears with teeth that are not hardened can be hardened to fit your application. Hardening a gear’s teeth increases its wear resistance.
For technical drawings and 3-D models, click on a part number.


Face Wd. | Number of Teeth | OD | For Shaft Dia. | Mounting Distance | Material | Teeth Heat Treatment | Each | |
Round Bore | ||||||||
---|---|---|---|---|---|---|---|---|
1/4" | 18 | 0.75" | 3/8" | 0.74" | 303 Stainless Steel | Not Hardened | 0000000 | 000000 |
Plastic Ratcheting Gears

A light duty alternative to metal, these plastic ratcheting gears run quieter than metal gears and have good corrosion and chemical resistance. Used to prevent unwanted motion in spools, clocks, and printers, ratchet gears have sloped teeth that allow motion in one direction and prevent it in the other.
A pawl is required to prevent backward motion.
For technical drawings and 3-D models, click on a part number.

Face Wd. | Number of Teeth | OD | For Shaft Dia. | Mounting Distance | Material | Fabrication | Color | Each | |
Round Bore | |||||||||
---|---|---|---|---|---|---|---|---|---|
1/4" | 18 | 0.75" | 3/8" | 0.74" | Nylon Plastic | Machined | White | 0000000 | 000000 |
Gear Rod Stock


Machine your own gears to fit the exact face width and shaft diameter required. Rod stock has teeth with a 20° pressure angle, the current industry standard. 20° pressure angle gears have thicker, stronger teeth than 14½° pressure angle gears. Teeth are not hardened so you can machine and harden them to fit your application. Hardening a gear’s teeth increases its wear resistance. Also known as spur gear rod stock.
For gears to mesh correctly, they must have the same pressure angle and pitch.
For technical drawings and 3-D models, click on a part number.
Gear Pitch | Number of Teeth | Gear Pitch Dia. | OD | Lg. | For Shaft Dia. | Material | Each | |
24 | 16 | 0.667" | 0.75" | 1 ft. | 1/32"-3/8" | 1215 Carbon Steel | 0000000 | 000000 |