About Gears
More
Quick-Grip Screw-Clamp Bushings
Also known as Trantorque bushings, these tighten with a twist of the collar nut—no screws needed. As you tighten the collar nut, the inner sleeve contracts onto the shaft and the outer sleeve expands to hold your sprocket, pulley, or gear.
For technical drawings and 3-D models, click on a part number.
High-Strength Corrosion-Resistant HTD Timing Belt Pulleys
Move belts forward and backward or stop and start them in precise positions, especially in areas where rust is a concern. The curved teeth on these high-torque drive (HTD) pulleys have more surface contact with belts than traditional trapezoidal teeth, which allows you to apply more torque without damaging belts. These teeth fit together seamlessly to prevent backlash, or unwanted movement of the belt on the pulley, for a smooth, quiet cycle. These pulleys are often used in 3D printing, machine tool drives, robotics, and other applications where precision is essential. They are also known as curvilinear belt pulleys.
Pair pulleys with an HTD timing belt that has the same pitch. The width of your belt should not be larger than the maximum belt width listed.
Aluminum pulleys will not rust in damp or humid environments, but water left on the surface will cause them to corrode.
For technical drawings and 3-D models, click on a part number.
Manufacturer Series | OD, mm | Number of Teeth | Pitch, mm | For Shaft Dia., mm | Bore Type | Inside Wd., mm | Outside Wd., mm | Overall Wd., mm | Pitch Dia., mm | Number of Flanges | Fabrication | Hub Dia., mm | Each | |
For 9 mm Max. Belt Wd. | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Gates PowerGrip 2GT | 15 | 20 | 2 | 5 | Finished | 10 | 11.2 | 19 | 12.73 | 1 | Machined | 15 | 0000000 | 00000 |
Metal Bevel Gears
A type of miter gear where one gear (sometimes called a pinion) is smaller than the other, bevel gears provide right-angle speed reduction at speed ratios ranging from 2:1 to 5:1. All are carbon steel for strength; they're compatible with plastic bevel gears. Teeth are not hardened so you can harden them to fit your application. Hardening a gear’s teeth increases its wear resistance.
A complete set consists of a gear and pinion (sold separately). For a gear and pinion to mesh correctly, they must have the same pressure angle, pitch/module, and face width. Speed ratio is the ratio by which shaft speed is reduced when transferring motion from pinion to gear. To increase shaft speed, transfer motion from gear to pinion. Changing shaft speed also changes torque: as speed decreases, torque increases.
For technical drawings and 3-D models, click on a part number.
Hub | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Face Wd., mm | Module | Pressure Angle | Speed Ratio | Number of Teeth | Gear Pitch Dia., mm | OD, mm | Overall Wd., mm | For Shaft Dia., mm | Mounting Distance (A), mm | Dia., mm | Wd., mm | Material | Each | |
Round Bore | ||||||||||||||
8 | 1.25 | 20° | 2:1 | 40 | 50 | 51 | 19 | 10 | 27 | 32 | 10 | Black-Oxide 1045 Carbon Steel | 00000000 | 000000 |
Hub | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Face Wd., mm | Module | Pressure Angle | Speed Ratio | Number of Teeth | Gear Pitch Dia., mm | OD, mm | Overall Wd., mm | For Shaft Dia., mm | Mounting Distance (B), mm | Dia., mm | Wd., mm | Material | Each | |
Round Bore | ||||||||||||||
8 | 1.25 | 20° | 2:1 | 20 | 25 | 28 | 19 | 8 | 36 | 22 | 10 | Black-Oxide 1045 Carbon Steel | 00000000 | 000000 |
Plastic Bevel Gears
Reduce speeds where noise, corrosion, and frequent lubrication are a concern. Compared to metal gears, these nylon gears run more quietly, won't rust, and don't need to be lubricated. Because they’re self-lubricating, these bevel gears are commonly used in food machinery. They should not, however, come in direct contact with food or chemicals that will come in contact with food.
A complete set consists of a gear and pinion (sold separately). For a gear and pinion to mesh correctly, they must have the same pressure angle, module, and face width. Plastic pinions can also be mated with metal gears, and plastic gears with metal pinions.
Speed ratio is the ratio by which shaft speed is reduced when transferring motion from pinion to gear. To increase shaft speed, transfer motion from gear to pinion. Changing shaft speed also changes torque: as speed decreases, torque increases.
For technical drawings and 3-D models, click on a part number.
Hub | ||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Face Width, mm | Module | Pressure Angle | Speed Ratio | Number of Teeth | Gear Pitch Dia., mm | OD, mm | Overall Width, mm | For Shaft Diameter, mm | Mounting Distance (A), mm | Material | Fabrication | Color | Diameter, mm | Width, mm | Each | |
Round Bore | ||||||||||||||||
8 | 1.25 | 20° | 2:1 | 40 | 50 | 50.7 | 19 | 10 | 27 | Nylon Plastic | Molded | Blue | 32 | 10 | 00000000 | 000000 |
Hub | ||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Face Width, mm | Module | Pressure Angle | Speed Ratio | Number of Teeth | Gear Pitch Dia., mm | OD, mm | Overall Width, mm | For Shaft Diameter, mm | Mounting Distance (B), mm | Material | Fabrication | Color | Diameter, mm | Width, mm | Each | |
Round Bore | ||||||||||||||||
8 | 1.25 | 20° | 2:1 | 20 | 25 | 28 | 19 | 8 | 36 | Nylon Plastic | Molded | Blue | 22 | 10 | 00000000 | 000000 |