System of Measurement System of Measurement |
---|
|
Component Component |
---|
|
Material Material |
---|
|
Overall Width Overall Width | Show |
---|
|
Overall Width Overall Width | Hide |
---|
Gear Type Gear Type |
---|
![]() | Ratchet |
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
Bore Type Bore Type |
---|
![]() | Round |
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
---|
Bushing Type Bushing Type |
---|
|
Maximum Torque Maximum Torque |
---|
|
Shaft Mount Type Shaft Mount Type |
---|
|
Teeth Heat Treatment Teeth Heat Treatment |
---|
|
Fastener Tightening Torque Fastener Tightening Torque |
---|
|
About Gears
More
Self-Centering Screw-Clamp Bushings


A mounting flange prevents movement during tightening, so it's easy to center these bushings in your sprocket. They are also good for shock loads. When you tighten the included screws, the bushing's inner sleeve contracts onto the shaft and the outer sleeve expands to hold your sprocket, pulley, or gear. They can be mounted on shafts with or without keyways.
For technical drawings and 3-D models, click on a part number.
For Shaft Dia. | OD | Overall Wd. | Max. Torque, in.-lbs. | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
14mm | 28mm | 24mm | 640 | 42 | Steel | Clamping Screws | 0000000 | 000000 |
16mm | 30mm | 24mm | 900 | 42 | Steel | Clamping Screws | 0000000 | 00000 |
18mm | 32mm | 24mm | 990 | 42 | Steel | Clamping Screws | 0000000 | 00000 |
19mm | 33mm | 24mm | 1,050 | 42 | Steel | Clamping Screws | 0000000 | 00000 |
Metal Ratcheting Gears

Compared to plastic gears, these metal ratcheting gears are better for high-load, high-speed, and heavy duty applications. Used to prevent unwanted motion in jacks, tie downs, clutches, and winches, ratchet gears have sloped teeth that allow motion in one direction and prevent it in the other.
Gears with hardened teeth are more wear resistant than gears with teeth that are not hardened.
For technical drawings and 3-D models, click on a part number.


Hub | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Face Wd. | Number of Teeth | OD | For Shaft Dia. | Mounting Distance | Material | Teeth Heat Treatment | Overall Wd. | Dia. | Wd. | Each | |
Round Bore | |||||||||||
12mm | 50 | 50mm | 12mm | 45.5mm | 1045 Carbon Steel | Hardened | 24 mm | 35 mm | 12 mm | 0000000 | 000000 |
12mm | 60 | 60mm | 15mm | 48.2mm | 1045 Carbon Steel | Hardened | 24 mm | 40 mm | 12 mm | 0000000 | 00000 |
12mm | 80 | 80mm | 15mm | 54.7mm | 1045 Carbon Steel | Hardened | 24 mm | 50 mm | 12 mm | 0000000 | 00000 |
12mm | 100 | 100mm | 15mm | 62.2mm | 1045 Carbon Steel | Hardened | 24 mm | 50 mm | 12 mm | 0000000 | 00000 |