Sets include assorted keys with long shafts that reach into tight spots. The plastic-covered handles provide a good grip for your whole hand.

Sets include an assortment of short keys that fit in tight spaces where others can't.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t.

These assorted keys have a textured grip that provides comfort, slip resistance, and maximum torque. They have a long shaft for reaching into tight spots to turn fasteners.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. The textured grip provides comfort, slip resistance, and maximum torque.

The economical choice, these sets include an assortment of keys with a simple loop handle. The long shaft reaches into tight spots and the T-handle provides a good grip for your whole hand when turning fasteners.

These sets include an assortment of keys with a ball end on the long shaft, which allows angled entry to turn screws in hard-to-reach areas. The short shaft provides additional torque.

The assorted keys in these sets have a long shaft for more reach and a short shaft for more torque when turning fasteners.

These assorted keys have an extra-long shaft that provides access to fasteners in deep recesses. To change tips, use a hex key to loosen the set screw.

These assorted keys have a ball-end tip with a retaining ring that grips inside the recess to hold screws in place and allows angled entry to turn fasteners in hard-to-reach areas.

The long shaft provides more reach and the short shaft more torque. Protect your stainless steel screws by using a stainless steel key. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Each slot is marked with the size. Set these organizers on a bench top or wall mount.

The assorted keys in these sets have a small T-handle that prevents you from generating too much torque when turning a fastener. They are often used to install carbide inserts in cutting tools.

A retaining ring on the tip grips inside the recess to hold screws in place. Often used to install carbide inserts in cutting tools, these keys have a small T-handle that prevents you from generating too much torque when turning a fastener.

The assorted keys in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900 and ASTM F1505-01. They have a long shaft that reaches into tight spots to turn fasteners.

A ratchet mechanism turns fasteners more quickly than a standard bit driver. Insert a bit into the shaft and a magnet holds it in place.

Position the head anywhere along the handle.

Also known as clamping pins, these bolts have a collar that slides along the shaft and can be welded in place to clamp work in place and prevent over torquing.

Use these pins for visibility or to color-code processes. For a more secure hold than standard quick-release pins, they lock in place until you push the button to release the spring-loaded retaining balls.

These pins adjust to take up play in a system or hold parts in holes of varying thicknesses. Spin the handle up or down, then tighten the locknut to change the length by up to ½”. Pins lock in place until you push the button to release the spring-loaded retaining balls.

A T-handle makes these pins easy to grip. The shoulder keeps a portion of the pin outside the hole and makes them easy to grab.

A T-handle makes these spring plungers easy to grip.

Mount these knobs into a threaded hole. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

Like locknuts, these knobs have a nylon insert that grips threads to resist loosening. Long shafts can thread through these knobs for mounting versatility. Use the knobs as a grip to position, tighten, and hold fixtures, equipment, and machinery.

Control devices with round or D-shaped shafts and view settings at a glance with a pointer.

These latches have a spring-wire cam that slips under a receiving catch on a cabinet body to create tension and hold cabinet doors and drawers closed.

These latches are IP65 rated for protection against dust, dirt, and low-pressure washdowns.

Designed for use in 1/2" dia. through holes.

Also known as compression cam locks, turn the handle a quarter-turn to latch, then another quarter-turn to draw the cam firmly against the door or drawer surface.

Choose these locks if you need to open several with the same key.

In addition to an IP65 rating for low-pressure washdown environments, these locks have a squeeze-release handle to prevent accidental opening when unlocked.

The mounting screws on these locks are concealed to prevent tampering.

Open these locks with both a master key and their own unique key.

Designed for protection against dust, dirt, and washdowns, these padlockable latches are IP65 rated.

These latches are typically used to secure hoods and covers.

Choose these locks if you need several that open with the same key.

Attach a pressure gauge to the side port on these valves. Use with water and air.

Install these low-profile valves in tight spots. Use with water, oil, air, and inert gas.

These valves can handle at least twice the pressure of other compact valves. Install them in tight spots. Use with water, oil, air, and inert gas.

These valves have union fittings that disassemble for fast installation and removal from pipelines. Use with water, air, and inert gas.

Plastic provides a lightweight and economical alternative to metal. All valves have barbs that grip onto tubing for a secure hold. They’re for use with water, oil, air, and inert gas.

Threads and a hex nut below the handle allow you to install these valves in instrument panels. For extra gripping power and a strong seal, they have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. Use these valves with water, oil, air, inert gas, and steam.

Solder these valves to metal tubing for a permanent, leak-tight connection. Use with water, oil, air, inert gas, and steam.

Use these valves as a mainline shutoff in natural gas and propane pipelines.

For chemical-processing applications in confined areas, these valves have an EPDM seal and a PVC or CPVC body to withstand aggressive and corrosive solutions and a low-profile handle to fit in tight spots.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves have a fluoroelastomer seal and a plastic body that can withstand aggressive and corrosive solutions in chemical-processing applications.

Union fittings on both ends of these valves disassemble for fast installation and removal from your pipeline. Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves have a fluoroelastomer seal and a plastic body that can withstand aggressive and corrosive solutions in chemical-processing applications.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves meet NSF/ANSI Standard 61, which means they’re safe to use with drinking water systems.

These valves meet NSF/ANSI 61 for use in drinking water lines.

A compression sleeve bites into tubing as you tighten the nut, forming a strong seal. These valves are for use with air. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Also known as block and bleed valves, these have two vent ports to isolate pressure gauges, switches, and other components in high-pressure systems for maintenance, calibration, and sampling without interrupting the process. They are rated for up to 10,000 psi. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Rated for nearly twice the maximum temperature of standard threaded precision flow-adjustment valves, these can handle up to 700° F. They’re for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

With 45° flared tube fittings, these valves form a tight seal on metal tubing. Use with air. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. The 316 stainless steel body and seal, the PTFE seat and packing, and the Monel needle can withstand aggressive and corrosive solutions in chemical-processing applications. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Threads and a hex nut below the handle let you install these valves through instrument panels. They are for use with water, oil, air, and inert gas. All divert flow between ports.

For easy installation and removal from pipelines, all ends on these valves have union fittings that disassemble into multiple pieces. Their fluoroelastomer seal and plastic body can withstand aggressive and corrosive solutions for diverting flow between ports in chemical-processing applications.

Perform valve maintenance without unthreading pipe connections. These valves have a three-piece bolted body that comes apart for inline access to internal components. The fluoroelastomer seal and glass-filled polypropylene body can withstand aggressive and corrosive solutions for diverting flow in chemical-processing applications.