A black-phosphate finish provides mild corrosion resistance.

These inserts are the most corrosion-resistant thread-locking inserts we offer.

Adhesive on both the internal and external threads keeps these inserts in place and holds screws tight.

A black-phosphate finish provides mild corrosion resistance.

These inserts are made to stringent military specifications.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

These inserts have a high strength-to-weight ratio and resist acids and salt water better than nickel alloy and stainless steel inserts.

A distorted thread grips the screw to resist loosening.

A dry film keeps the screw from sticking or binding in these inserts during installation.

A dry film keeps the screw from sticking or binding in these inserts during installation.

Assortments include various sizes of helical inserts and a tap, a drill bit, and an installation tool for each thread size.

These kits have short-, normal-, and long-reach inserts, an installation tool, and a tap.

Made from brass, these inserts are nonmagnetic, corrosion resistant, and electrically conductive.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

Made from brass, these inserts are electrically conductive, nonmagnetic, and have good corrosion resistance.

The flange keeps these inserts from pulling through a hole. Press them in from the underside of material, and install a screw from the top of material.

Use these inserts to install fine-thread screws in existing holes.

70% lighter than stainless steel, these aluminum inserts are mildly corrosion resistant and nonmagnetic.

Install these inserts into plastic parts to create a secure base for fasteners.

The tapered shape makes it easier to guide these inserts into a hole during installation. Use a drill bit to create a straight hole, then taper the top half.

Made from brass, these inserts are nonmagnetic, mildly corrosion resistant, and electrically conductive.

Steel inserts have high strength for durability.

The flange keeps these inserts from being pulled through a hole and provides a load bearing surface.

Steel inserts have high strength for durability.

The most corrosion resistant tee nut inserts we offer, these inserts stand up to chemicals and salt water.

Fewer prongs than other tee nut inserts reduce the risk of splitting hardwood—these inserts have three short prongs.

Use where vibration is a concern—these tee nut inserts have distorted threads that lock screws in place.

Knurls hold these inserts in hardwoods such as oak, maple, and walnut to prevent twisting.

An open end allows long screws and bolts to pass through the insert.

Press these inserts into a drilled hole and the flexible metal teeth anchor them in the material. Use them with carbon fiber, fiberglass, and garolite.

A smooth base provides more contact with the mating surface than weld nuts with projections.

Weld these nuts to stainless steel surfaces.

These nuts can be used in channels and tight spaces where round-base weld nuts won't fit.

Weld these nuts to stainless steel surfaces.

These screw-mount nuts are often used to attach glides and levels to wood.

Stronger than stainless steel, these nuts are comparable in strength to Grade 9 bolts.

About twice as strong as aluminum rivet nuts, these steel rivet nuts are zinc plated for mild corrosion resistance.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

Wedges under the flange lock the nut in place in soft materials such as brass and aluminum.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

A nonconductive rubber coating insulates the nut from electricity, seals out moisture, and damps vibration.

About twice as strong as aluminum rivet nuts, these low-profile rivet nuts have a cadmium or tin-zinc plating for corrosion resistance.

These low-profile rivet nuts are one-third the weight of steel and have mild corrosion resistance.

A PVC coating minimizes the chance of scratching the surface of your material. These rivet nuts are more corrosion resistant than zinc-plated steel rivet nuts.

Threads float inside the nut so you can install a screw at a slight angle to align with off-center parts. They’re also known as Riv-Float nuts.

About half the strength of medium-strength steel coupling nuts, these metric nuts are for light duty fastening applications.

Choose these standoffs for their adherence to NAS 1831 specifications.

Protect components from electrical charges.

These standoffs are designed to fit in the limited space of compact electronics such as laptops and hand-held devices.

Use these rivet nuts for light duty fastening in low-clearance applications. Assortments include rivet nuts, mandrels, and an installation tool.

A zinc plating provides corrosion resistance in wet environments.

These 18-8 stainless steel anchors have good chemical resistance.

A zinc plating provides corrosion resistance in wet environments.

Install like a stud anchor—just thread the anchor, a nut, and a washer onto the end of a threaded rod, drive into a hole, and turn the nut to expand the base. Also known as rod anchors, they're often used with threaded rod to hang pipe and wiring.

Also known as double expansion anchors, these expand from both sides for full contact and a secure hold.

The fastest way to install shallow-hole female-threaded anchors. Just push the tip of the tool into the anchor and turn the tool with a power drill.

Also known as lag shields, these anchors are designed for use with large-diameter wood screws.

Also known as mungo anchors, these have large fins that prevent rotation.

Use with any type of sheet metal or wood screw.

For narrow holes and small cavities where toggle anchors won't fit.

Fins prevent these anchors from spinning during installation.

A drilled hole is required for installation.

Use these corrosion-resistant fittings in a low-pressure pipe line.

Choose these fittings when you want the same high-quality found in our low-pressure pipe fittings, but need more strength to handle higher pressures.

Use these fittings in extreme-pressure conditions up to 15,000 psi.