Fill the fuel tank with gasoline to remove water at sites without power. These pumps are self-priming, which means they create a suction force to draw liquid upward and fill the pump chamber. They can be mounted up to 20 feet above your liquid source. All have a pull-start engine. Pumps are not submersible. They cannot be sold to the regions listed due to import and engine regulations.

Wheel kits (sold separately) include two 10" diameter wheels, hardware, and fasteners.

Note: Pumps must be filled with liquid before use. They need a constant flow of liquid and cannot run dry.

Built with high-chromium stainless steel components, this pump stands up to salt water with up to 25% sand by volume and resists wear caused by abrasive particles. Fill the fuel tank with gasoline to remove water at sites without power. Pump is self-priming, which means it creates a suction force to draw liquid upward and fill the pump chamber. Mount up to 20 feet above your liquid source. Pump has a pull-start engine. It is not submersible. This pump cannot be sold to Canada due to import regulations.

Wheel kits (sold separately) include two 10" diameter wheels, hardware, and fasteners.

Note: Pump must be filled with liquid before use. It needs a constant flow of liquid and cannot run dry.

With a polypropylene housing, these pumps are about half the weight of other gasoline-powered pumps. Fill the fuel tank with gasoline to remove water at sites without power. Pumps are self-priming, which means that they create a suction force to draw liquid upward and fill the pump chamber. Mount up to 20 feet above your liquid source. They have a pull-start engine.

Wheel kits (sold separately) include two 10" diameter wheels, hardware, and fasteners.

Pumps cannot be sold to Canada due to import regulations.

Note: Pumps must be filled with liquid before use. They need a constant flow of liquid and cannot run dry.

Install these pumps right in your line and engage the lever handle to start pumping. They have few moving parts that can fail for an extended service life. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry.

Wheel these pumps to remote areas with no power. They can handle sewage water with thick sludge, silt, and debris up to 2" in diameter. Pumps are self-priming, which means they create a suction force to draw liquid upward and fill the pump chamber. Mount up to 20 feet above your liquid source. All have a pull-start engine. They are not submersible. These pumps cannot be sold to Canada due to import regulations.

Pump with a tank capacity of 1.6 gallons includes an electric starter that operates on a 12-volt battery (sold separately). It cannot be sold outside the United States because of energy efficiency requirements.

Note: Pumps must be filled with liquid before use. They need a constant flow of liquid and cannot run dry.

Transfer raw sewage water that contains solids up to 2” in diameter. These pumps have a float switch with a separate cord that can unplug, so you can replace the switch without replacing the whole pump. The length of the float switch cord is adjustable. Turn-on and turn-off levels will vary according to the length of the cord. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry.

Pumps with male discharge port have a horizontal discharge.

Pumps with female discharge port have a vertical discharge.

These pumps provide over 50% more flow than standard plug-in activated pumps for sewage water. They activate when plugged in. You can add a plug-in switch to control when the pump activates. Pumps are equipped with a large intake and rugged impeller to transfer raw sewage water with solids up to 2" in diameter. All have a cast iron housing that stands up to demanding environments. Pumps can run dry.

Pumps with wire leads can be connected to a three-pronged plug or wired directly to a power source.

These pumps provide about 25% more flow than standard float-switch activated pumps for sewage water. Equipped with a large intake and rugged impeller, they transfer raw sewage water with solids up to 2" in diameter. All have a cast iron housing that stands up to demanding environments. The float switch is wired to the pump. Pumps can run dry.

These pumps provide about 25% more flow than standard float-switch activated pumps for sewage water. The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Pumps are equipped with a large intake and rugged impeller to transfer raw sewage water with solids up to 2" in diameter. They have a cast iron housing that stands up to demanding environments. Pumps can run dry.

Also known as a grinder pump, this pump has stainless steel blades that prevent clogs by breaking down sewage into an easy-to-transfer slurry. Do not use with metal particles or debris that could damage blades. Pump has an epoxy-coated cast iron housing that stands up to demanding environments. The float switch is wired to the pump. Submerge while in use and do not run dry.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Also known as grinder pumps, they have stainless steel blades that prevent clogs by breaking down sewage into an easy-to-transfer slurry. Do not use with metal particles or debris that could damage blades. Pumps have a cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Equipped with a large intake and rugged impeller, these pumps transfer raw sewage water with solids up to 2" in diameter. They have a cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

Equipped with a large intake and a rugged impeller, this pump transfers raw sewage water with solids up to 2" in diameter. It has a cast iron housing that stands up to demanding environments. The float switch is wired to the pump. Submerge while in use and do not run dry.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Equipped with a large intake and rugged impeller, these pumps transfer raw sewage water with solids up to 2" in diameter. They have a cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

These pumps have a heavy duty motor with sealed bearings that generates a flow rate similar to our other sump pumps for sewage water while using fewer amps. Use them to transfer raw sewage water with solids up to 2" in diameter. The float switch is wired to the pump. Submerge while in use and do not run dry.

Pump with wire leads can be connected to a three-pronged plug or wired directly to a power source.

Pumps have a heavy duty motor with sealed bearings that generates a flow rate similar to our other sump pumps for sewage water while using fewer amps. Connect them to a three-pronged plug or wire them directly to a power source to activate. You can also add a plug-in switch to control when the pump activates. Pumps transfer raw sewage water with solids up to 2” in diameter. Submerge while in use and do not run dry.

Convenient for applications where a sump pit is impractical, these pumps include a basin with a vent on top. They handle raw sewage water with solids up to 2" in diameter. The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump.

These pumps have an explosion-proof motor that is rated for use where hazardous material is present. Since the motor is totally enclosed fan cooled (TEFC) and never comes into contact with the water, the pump can be used with hot water up to 300° F. A pedestal-mounted motor design provides easy access for maintenance. The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump.

Hazardous location environmental ratings indicate whether manufacturers have included safety features in products to facilitate their safe use in a hazardous environment. Before selecting a product for a hazardous location, ensure it is rated for your environment. See About Hazardous Location Environmental Ratings.

Since the motor is totally enclosed fan cooled (TEFC) and never comes into contact with the water, these pumps can be used with hot water up to 200° F. A pedestal-mounted motor design provides easy access for maintenance. The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump.

Float switch repair kits (sold separately) include a float, a float rod, and a switch.

Use these pumps to move higher volumes of water with solids than other sump pumps. They activate when plugged in; add a plug-in switch to control when the pump activates. Also known as effluent pumps, they accommodate solids up to 3/4" in diameter. They are often used with liquid waste that has passed through a septic tank, so most solids are removed. Pumps have an epoxy-coated cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

Pumps with wire leads can be connected to a three-pronged plug or wired directly to a power source.

Use this pump to move higher volumes of water with solids than other sump pumps. It has a screenless, nonclogging design to handle solids up to 3/4" in diameter. The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Also known as an effluent pump, it is often used with liquid waste that has passed through a septic tank, so most solids are removed. Pump has an epoxy-coated cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

Also known as effluent pumps, these accommodate solids up to 3/4” in diameter. They’re often used with liquid waste that has passed through a septic tank, so most solids are removed. The float switch is wired to the pump. All have an epoxy-coated cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Also known as effluent pumps, these accommodate solids up to 3/4" in diameter. They’re often used with liquid waste that has passed through a septic tank, so most solids are removed. They have an epoxy-coated cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

The float switch has a separate cord that can unplug, so you can replace the switch without replacing the whole pump. Also known as effluent pumps, these accommodate solids up to 3/4" in diameter. They’re often used with liquid waste that has passed through a septic tank, so most solids are removed. All have an epoxy-coated cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

Use these pumps at temperatures up to 200° F. Also known as effluent pumps, they accommodate solids up to 3/4" in diameter. They’re often used with liquid waste that has passed through a septic tank, so most solids are removed. The float switch is adjustable and wired to the discharge pipe. Pumps have an epoxy-coated cast iron housing that stands up to demanding environments. Submerge while in use and do not run dry.

Replacement float switches (sold separately) include a float, connecting wires, and a seal.