When working in tight spaces, these short wrenches fit where others can't.

Flip these wrenches over to ratchet in the opposite direction.

A lever reverses the ratchet direction.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Flip these wrenches over to ratchet in the opposite direction.

Suitable for occasional maintenance work, these sets are imported.

A lever reverses the ratchet direction.

One head is angled 60° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

These are also known as tappet wrenches.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

Fit the narrow head into tight spaces and around thin fasteners.

One head is angled 75° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

The handle is covered in rubber for a comfortable grip.

A gasket seals in permanent lubrication and keeps out dirt, dust, and moisture.

Twist the grip to rapidly turn a socket before final tightening or to remove a fastener once loosened. The handle also swings like a traditional ratchet wrench.

Pivot the head to access fasteners in tight spots.

The 20° offset head provides clearance when reaching over obstructions.

Turn sockets in the most confined spaces.

Extend the shaft for additional length.

Position the head anywhere along the handle.

The ratcheting mechanism turns sockets quickly.

Pivot the head to access fasteners in tight spots.

Unlike most torque wrenches, you don’t have to return the torque setting to the lowest value after use. These tools are also known as split-beam torque wrenches.

Trust the precision of your measurements—these wrenches are accurate to ±1%.

The most advanced torque wrenches we offer, these tools store and recall up to 1,500 torque and angle measurements.

Trust the precision of your measurements—these wrenches are accurate to ±2%.

Turn sockets from above when there's not room to swing a standard wrench handle.

When the set torque is reached, these wrenches signal with an audible click and an impulse in the grip.

These short sockets fit spaces where height clearance is limited.

With a plastic insert, these sockets firmly grip hex nuts and bolts without rounding them or scratching highly polished finishes.

Pivot the head to access fasteners from an angle.

Also known as pipe plug sockets, these sockets have a square shape that provides the best possible grip on square fasteners and prevents rounding.

Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.

Make maximum contact with all sides of a fastener to reduce slipping. These sockets are also known as torque adapters.

Extra-long bits allow access to hard-to-reach fasteners.

Extra-long bits allow access to hard-to-reach fasteners.

These sockets are also known as pin-in-Torx bits.

Pivot the head to access fasteners from an angle.

Suitable for occasional maintenance work, these sets are imported.

Suitable for occasional maintenance work, these sets are imported.

For high quality at a lower price, choose these U.S.A.-made sets.

Quickly position these sockets on square fasteners.

Extra-long bits allow access to hard-to-reach fasteners.

Extra-long bits allow access to hard-to-reach fasteners.

Keep a convenient mix of hex, Torx, Phillips, and slotted bit sockets on hand.

Extra-long bits allow access to hard-to-reach fasteners.

Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.

The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.

Attach to your socket for a longer reach.

Convert from one square drive size to another.

Push the square drive through the adapter to change size.

The square drive has a rounded shape that allows the extension to pivot inside the socket opening and turn it from an angle.

Lock your socket into the extension to prevent accidental disengagement.

A digital display shows how torque measurements change as you turn the wrench. Set the desired torque and angle—lights and an audible alarm indicate when target has been reached or exceeded.

Fit these adapters between your wrench and socket to enable finger tightening.

Bend these extensions around obstructions to access hard-to-reach fasteners.

The handle is covered in plastic for a comfortable grip.

Press the lever to lock the jaw and keep these wrenches clamped on your work, leaving your hands free.

Flip the wrench over to use the raised section on the head as a hammer.

A ratchet mechanism in the head allows you to turn fasteners in tight spaces without removing and repositioning the wrench.

The heads are angled to provide clearance around obstructions.

Ratchet mechanisms allow you to turn fasteners in tight spaces without removing and repositioning the tool.

An insulated handle protects against accidental contact with live electrical circuits. These wrenches are tested to 1,000 volts to meet IEC 60900.

The offset head gives you additional clearance to turn hard-to-reach fasteners.

A ratchet mechanism allows you to turn fasteners in tight spaces without removing and repositioning the wrench.

These wrenches are polished for a mirror-like finish.

Turn nuts on bolts and threaded rod, which can pass through the short end of the wrench. For additional leverage, slip a bar through the short end to create a T-handle.

Change out the pins to fit a different hole size.

Turn the end of the handle to set torque, and the wrench makes an audible click when it reaches the setting.

All of the keys in these sets have an extra-short leg to fit into tight spots and a ball end to turn screws at an angle in hard-to-reach places. Their bright chrome-plated finish makes them easy to see, reducing the chance you’ll lose them.

Sets include assorted keys with long shafts that reach into tight spots. The plastic-covered handles provide a good grip for your whole hand.

The assorted keys in these sets have a long shaft for more reach and a short shaft for more torque when turning fasteners.

These sets include an assortment of keys with a ball end on the long shaft, which allows angled entry to turn screws in hard-to-reach areas. The short shaft provides additional torque.

These assorted keys have a ball-end tip with a retaining ring that grips inside the recess to hold screws in place and allows angled entry to turn fasteners in hard-to-reach areas.

Sets include an assortment of drivers with soft, contoured handles that provide comfort and the best possible grip for achieving maximum torque.

These standard-length drivers are found in every tool box.

A cushioned grip over a plastic core adds comfort and some slip resistance.

Sets include an assortment of drivers with a suede-like textured handle that provides a firm grip, even for oily hands.

The assorted drivers in these sets have a shaft that extends through the handle and a steel end cap, which provide the strength to absorb hammer blows.

The assorted drivers in these sets have a holding mechanism at the tip that ensures the screw won’t slip off.

The tips of these assorted drivers have ribbed grooves that grip the surface of the recess to reduce slipping and minimizing the pressure required to achieve maximum torque.

When working at heights, secure a lanyard to the ring on these tools to prevent drops. The ring rotates around the shaft so the driver turns freely.

Use the stud on the handle to bend and loop solid wire for making connections to outlets and switches.

Also known as ESD-safe screwdrivers, the handle drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment.