Absorbing blows and resisting fire, these ABS filaments produce holders, guards, housings, and other parts that protect sensitive, flammable equipment and machinery. They’re rated UL 94 V-0, which means they meet strict flammability standards. Print them on a fused filament fabrication (FFF) 3D printer. Because they have a high melting point, they require a heated print surface and may warp as they cool. They also emit fumes, so you need direct ventilation, such as a fume exhauster, to print safely.

ABS filaments have a lower printing temperature than polycarbonate ABS filaments, so they’re easier to print. You don’t need to store them with a desiccant to keep them dry, since they resist absorbing moisture from the air.

Polycarbonate ABS filaments are about 33% stronger and handle slightly higher temperatures than standard ABS filaments.

Tensile strength is the best measure of a filament’s overall strength. Similar to the stress applied on a rope during a game of tug-of-war, it’s the amount of pulling force a material can handle before breaking. A higher rating means a stronger filament. A tensile strength of 5,000 psi and above is considered good; 12,000 psi and above is excellent.

Maximum exposure temperature is the point at which a printed part will begin to deform. Above this temperature, your part will start to lose structural integrity.

Create tool handles, tote trays, enclosures, and other parts that are banged or dropped often and used near sensitive electronics. These filaments are made of durable ABS or polycarbonate—roughly four times tougher than PLA—with a compound that diverts electrostatic discharges away from equipment. Print them on a fused filament fabrication (FFF) 3D printer. Due to their high melting point, they require a heated printer bed and tend to warp as they cool. They also emit an odor as they print, so you’ll need an enclosed printer or fume exhauster.

ABS filaments are a good place to start if you’re printing impact-resistant parts.

Polycarbonate filaments are nearly twice as impact resistant and stand up to heat better than ABS filaments. However, their higher melting point makes them more difficult to print, since they need more heat and are more likely to warp.

To make sure your part dissipates static properly, use an electrical resistance tester to measure the surface resistivity. The target surface resistivity for these filaments is 10⁷ to 10⁹ ohms. To adjust the resistivity, change the temperature of your printer’s extruder. As the extruder’s temperature increases, so will the printed part’s resistivity.

Tensile strength is the best measure of a filament’s overall strength. Similar to the stress applied on a rope during a game of tug-of-war, it’s the amount of pulling force a material can handle before breaking. A higher rating means a stronger filament. A tensile strength of 5,000 psi and above is considered good; 12,000 psi and above is excellent.

Maximum exposure temperature is the point at which a printed part will begin to deform. Above this temperature, your part will start to lose structural integrity.

Print tough, long-lasting parts that won’t scratch or wear out from constant motion and friction, such as gears, bearings, and washers. You can even tap or drill the parts without them cracking or shattering.

Use these filaments with fused filament fabrication (FFF) printers. Because of their relatively high melting point, a heated printer bed is recommended. These filaments also emit fumes when printing, so it’s best to use them in an enclosed printer or to remove the fumes with a fume exhauster. Store them in a sealed container with a desiccant so they don’t absorb moisture in the air, which can make them unusable.

Carbon-fiber-filled nylon filaments are reinforced to make them the strongest and most rigid nylon in this offering. They are abrasive filaments that can damage soft metal nozzles, such as brass and copper, so use them with hardened steel nozzles.

Tensile strength is the best measure of a filament's overall strength. Similar to the stress applied on a rope during a game of tug-of-war, it's the amount of pulling force a material can handle before breaking. A higher rating means a stronger filament. A tensile strength of 5,000 psi and above is considered good; 12,000 psi and above is excellent.

Maximum exposure temperature is the point at which a printed part will begin to deform. Above this temperature, your printed parts will start to lose structural integrity.

Stretchy, soft, and sturdy, these filaments make durable parts that resist wear and breakage despite repeated use. Stronger than ABS and PLA filaments, they create long-lasting, wear-resistant parts, such as seals, sleeves, and gaskets, as well as components that take on high-impact forces, such as springs and snap-fit parts.

These filaments don't require a heated printer bed, and they won't shrink or warp when cooling. Use them with a fused filament fabrication (FFF) 3D printer. In general, these flexible filaments require a slow feed rate so they don't jam. Store them in a sealed container with a desiccant, or use a dehumidifying cabinet, since ambient humidity will cause the plastic to degrade and weaken.

For the most flexible parts, use durometer 85A TPU filaments. They're more flexible than PCTPE and other TPU filaments.

For a quick print without sacrificing flexibility, choose durometer 95A TPU filaments. They print much faster than other TPU filaments.

With nylon as an additive, PCTPE filaments are not only flexible, they're wear resistant and inherently slippery, so they're good for components that move and rub against other objects. They're also UL rated 94 HB and 94 V-2 for their ability to prevent the spread of flames both horizontally and vertically.

Tensile strength is the best measure of a filament's overall strength. Similar to the stress applied on a rope during a game of tug-of-war, it's the amount of pulling force a material can handle before breaking. A higher rating means a stronger filament. A tensile strength of 5,000 psi and above is considered good; 12,000 psi and above is excellent.

Maximum exposure temperature is the point at which a printed part will begin to deform. Above this temperature, your printed parts will start to lose structural integrity.

Made of pliable TPU with a conductive compound, these filaments produce wire, circuits, and other components that direct the flow of electricity in wearable and flexible devices, from watches to grippers. Combine them with an insulating material so the electricity flows only through the filament’s pathways and not the rest of the device. In addition to being flexible, TPU is also durable and handles stresses better than ABS and PLA.

Print these filaments on a fused filament fabrication (FFF) 3D printer. You don’t need a heated printer bed, and printed parts resist shrinking and warping as they cool. Because they’re flexible, these filaments print best at a slow, consistent rate; high print speeds could cause them to jam. They don’t stand up well to moisture, so store them in a dehumidifying cabinet or other sealed container with a desiccant to keep them dry.

To make sure your part conducts electricity properly, use an electrical resistance tester to measure the surface resistivity. The target surface resistivity for TPU is 10¹ to 10⁶ ohms. To adjust, change the temperature of your printer’s extruder. As the extruder’s temperature increases, so will the printed part’s conductivity.

Tensile strength is the best measure of a filament’s overall strength. Similar to the stress applied on a rope during a game of tug-of-war, it’s the amount of pulling force a material can handle before breaking. A higher rating means a stronger filament. A tensile strength of 5,000 psi and above is considered good; 12,000 psi and above is excellent.

TPU blended with a static-dissipative compound, these filaments make gaskets, springs, grippers, and other pliable parts that divert electrostatic shocks in a controlled way, protecting nearby electronics and sensitive equipment. They meet ANSI/ESD and IEC standards for manufacturing, packaging, transporting, and storing items that can be damaged by electrostatic shocks. In addition to being flexible, TPU is also durable and withstands stresses better than ABS and PLA.

Print these filaments on a fused filament fabrication (FFF) 3D printer. You don’t need a heated printer bed, and printed parts resist shrinking and warping as they cool. Because they’re flexible, these filaments print best at a slow, consistent rate; high print speeds could cause them to jam. They don’t stand up well to moisture, so store them in a dehumidifying cabinet or other sealed container with a desiccant to keep them dry.

Durometer 80A filaments are more flexible than durometer 95A and 74D filaments. Durometer 95A filaments have a balance of flexibility and strength. Durometer 74D filaments are tough and durable. Similar to a tire tread, they can bend repeatedly without cracking.

To make sure your part dissipates static properly, use an electrical resistance tester to measure the surface resistivity. The target surface resistivity for TPU is 10⁶ to 10⁸ ohms. To adjust the resistivity, change the temperature of your printer’s extruder. As the extruder’s temperature increases, so will the printed part’s resistivity.

Tensile strength is the best measure of a filament’s overall strength. Similar to the stress applied to a rope during a game of tug-of-war, it’s the amount of pulling force a material can handle before breaking. A higher rating means a stronger filament. A tensile strength of 5,000 psi and above is considered good; 12,000 psi and above is excellent.

Maximum exposure temperature is the point at which a printed part will begin to deform. Above this temperature, your printed part will start to lose structural integrity.

Build parts and prototypes from these filaments using Dremel fused filament fabrication (FFF) 3D printers. An RFID tag on the spool communicates with your printer, automatically adjusting it to the correct temperature and print speed for the filament material and notifying you when the filament is running out.

Nylon resists scratches and wear, and is often used to create parts that encounter constant friction such as gears or bearings. Nylon parts also won’t crack or shatter when they’re drilled or tapped. Exposure to humidity makes these filaments brittle and unusable, so they need to be stored in a sealed container with a desiccant. Like ECO-ABS, parts can warp during cooling and need a heated printer bed. Make sure your printer is connected to a ventilation system, as nylon emits fumes during printing.

Tensile strength is the best measure of a filament's overall strength. Similar to the stress applied on a rope during a game of tug-of-war, it's the amount of pulling force a material can handle before breaking. A higher rating means a stronger filament. A tensile strength of 5,000 psi and above is considered good; 12,000 psi and above is excellent.

Maximum exposure temperature is the point at which a printed part will begin to deform. Above this temperature, your printed parts will start to lose structural integrity.

Parts printed with these filaments absorb less moisture than other types of plastic, making them ideal for use in wet or humid environments. They are more durable and flexible than PLA, and easier to print than ABS. Use these filaments with fused filament fabrication (FFF) 3D printers, and print onto a heated print bed. Printing onto a cool surface causes the molten filament to change temperature rapidly, which can warp your designs. Although finished parts are moisture-resistant, these filaments are sensitive to humidity, and should be stored in a dehumidifying cabinet or a sealed container with desiccant.

PCTG holds up to a wide range of acids and bases without breaking down. It is often used for printing parts that will be exposed to chemicals and oils.

Tensile strength is the best measure of a filament's overall strength. Similar to the stress applied on a rope during a game of tug-of-war, it's the amount of pulling force a material can handle before breaking. A higher rating means a stronger filament. A tensile strength of 5,000 psi and above is considered good; 12,000 psi and above is excellent.

Maximum exposure temperature is the point at which a printed part will begin to deform. Above this temperature, your printed parts will start to lose structural integrity.