Shaped and sized for compatibility with wheel bearing locknuts on trucks and trailers, the sockets in these sets make it easy to install and remove locknuts.

A rubber seal and stainless steel hardware give these connectors excellent chemical resistance. They're rated NEMA 12, 4X, and IP65 for protection against corrosion, oil, and washdown environments.

Assemble a connector that can handle multiple applications at once. Combine inserts that send power, signal, and data with a base and a hood.

Carry up to four times the current of standard Compact Latching Connectors. The base and hood latch together securely, yet can be quickly detached for equipment repair or replacement.

These connectors have the same pin and socket configuration as connectors that meet MIL-DTL-26482, so they can be used with products that meet the same standard. Quickly mate them by pushing them together.

These connectors meet MIL-DTL-26482, so they're compatible with other products that meet the same standard. Quickly mate by pushing them together.

Connect and disconnect with the power on—spring-loaded contacts open like a switch when separating the connectors, preventing an electrical arc.

Meet international standards IEC 309-1 and 309-2.

Because they tightly thread to M12 connections, these connectors won’t let contaminants in or come loose from vibration in rugged industrial environments and automated systems as they send power and signal or just power to your equipment.

Safely use these connectors with 12 mm proximity switches, console lights, valves, and power supplies in food, beverage, and pharmaceutical applications—they’re FDA compliant for direct food contact.

Visually confirm your connector is working properly. A green light means your connector has power, while yellow means it has signal.

Often used to send power and signal to automated systems, motors, and pumps, these mini connectors carry higher currents than M5, M8, and M12 connectors.

Also known as dummy plugs, these plugs close the electrical circuit on your mini connector, so you can safely change devices or repair connections.

Send higher current than M12 connectors to automated systems, motors, and pumps in environments where washdowns are common.

Rated IP69K, these M16 connectors protect against dust, debris, and hot, high-pressure jets of water at high volumes.

Send signal and power to low-current devices with M8 connections in food processing and other sanitary applications.

A TPE cable protects these connectors from oil, weld slag, and other tough industrial stresses as they send signal and power to low-current devices with M8 connections.

Some of the smallest signal/power connectors we offer, these connectors fit in tight spaces and are often used in electronics.

A sealed housing protects connectors from weather. Sets include a plug and socket with wire leads already installed. They fit standard Molex connectors.

Each set includes one plug and one socket. These connectors withstand moisture, harsh engine fluids, and high temperatures. Also known as weather-pack connectors.

Use these connectors in vehicles and other agricultural and construction equipment. They have a sealed nylon housing that resists dust and temporary submersion.

These general purpose M23 connectors send power or signal to servomotors, servocontrollers, and servodrives.

Make secure connections with machine tools, robots, and other equipment that vibrates frequently and carries currents as high as 300 amps.

With thick threads similar to a light bulb, these connectors take only a few turns to lock into place for a secure connection in washdown and high-vibration areas. Detach them just as quickly for frequent maintenance.

Reduce the likelihood of slips and falls in high-traffic areas—connectors won't roll when stepped on.

Mount these receptacles to control cabinets and equipment in order to quickly connect and disconnect M29 power cords.

Deliver power to welding cable. These connectors withstand the high temperatures and high current found in welding applications.

Unlike traditional RJ45 connectors found in data centers, these connectors stand up to rugged industrial environments since they tightly thread to devices with M12 connections, sealing out contaminants and resisting shaking loose from vibration. Use them to transfer high-speed data between sensors, switches, computers, IO modules, programmable logic controllers (PLCs), and other equipment.

Step on or roll carts and platform trucks over these M12 cords without crushing them.

TPE insulation protects these cords from some of the toughest industrial conditions, including abrasion, coolants, chemicals, UV rays, and weld slag. Use them in areas with welding, machining, and fluctuating temperatures to send signal and power to M12 proximity switches, valves, and other devices.

These cords have a Nano M8 connector (also known as a pico connector) on one end and an USB Type-A connector on the other.

Also known as pico cords, these cords are often used with low-current 8 mm proximity and photoelectric switches.

These cords have an M8 connector on one end and an M12 connector on the other.

Often used for automated systems, motors, and pumps in tough industrial areas such as near welding and metal machining, these cords carry higher current than M5, M8, and M12 cords.

Connect multiple M8 and M12 cords to create a network between equipment. These blocks are often used to send signal and power to proximity switches and sensors.

Similar to branches extending from a tree, these cords disperse power from a main power line to run a chain of devices. Power high-amperage fans, pumps, and other machines in motor controls, conveyors, and sorting and packaging systems.

Often used in automation systems such as conveyors and sorters, these cords have plug and socket ends, so they quickly connect and disconnect for maintenance and do not need to be hardwired.

An isolated ground connection on these outlets protects computers and other sensitive equipment from external signals that interfere with the equipment’s performance.