Used to mount panels, signs, and dispensers, this foam tape absorbs shock and provides high strength holding power on rigid surfaces.

Tape is cut into convenient discs and rectangles.

Tape is cut into convenient discs and rectangles.

Use this tape outdoors for sealing and mounting signs and security control panels.

Repair ceiling tiles and pass-through windows in clean rooms with this foam tape with adhesive on both sides.

The clear side of this polyester tape is coated with silicone adhesive for mounting to silicone rubber, while the white side is coated with acrylic adhesive for a strong bond to metal and plastic.

Use this tape for light duty mounting, as well as to splice paper, foil, film, and fabric.

Particle and residue free, this tape meets clean room requirements. It has adhesive on both sides.

This thin paper tape has a high-bond adhesive on both sides that sticks to glossy surfaces and hard-to-bond plastics.

Create strong, permanent bonds that can replace mechanical fasteners.

This tape can withstand temperatures up to 300° F.

The acrylic adhesive on these sheets sticks to hard-to-bond materials, such as plastics and powder-coated surfaces.

Use these clear sheets for strong, invisible bonds.

A permanent adhesive on one side of this tape stays put, while a tacky adhesive on the other side lets you open and close bags or reposition signs.

Use these tapes for light duty mending and holding.

Patch and seal roofs, window frames, gutters, and vents with this conformable tape.

Stop water penetration with this tacky, flexible tape. It conforms to irregular shapes and expands to fill gaps. Use it on freezers, windows, and in marine applications.

An alternative to caulk and rubber sealants, this tape comes compressed and gradually expands to fill large gaps and voids.

When seams and joints begin to show wear, this super-strong reinforcing tape provides support. It is flexible yet nonelastic and stays in place even in damp conditions.

Wrap this tape around carbon fiber and other composite parts, then heat to 150° F. Tape shrinks to squeeze out air bubbles and apply pressure so parts cure without voids.

Make invisible repairs with this clear tape. The weatherproof adhesive won't turn yellow outdoors.

Patch and connect tarps with this thick, woven plastic tape.

This uncoated tape is thinner and more conformable than our other repair tape to reinforce irregular shapes.

When exposed to moisture, this resin-coated fiberglass tape becomes rock-hard in about 30 minutes. Use it for rigid, waterproof repairs.

This general purpose tape is suitable for most packaging applications.

An economical alternative to our standard packaging tape.

The strong backing on this kraft paper tape resists moisture and weathering, yet it can still be torn by hand.

Get peace of mind when packaging high-value and confidential items—this tape indicates a package has been opened.

Seal boxes with rough or challenging surfaces, such as corrugated and printed cardboard.

Use this tape for light duty bundling and strapping. Fiberglass fibers run along the length.

Twice as strong as our standard reinforced strapping tape for extra-heavy loads. Fiberglass fibers run along the length.

Thicker than our standard Strapping Tape, this tape can better hold and secure large, heavy items that may shift during transport.

When tape is removed, a red layer stays behind to indicate the package has been opened.

Also known as gaffer's tape, this conformable cloth tape leaves no residue when removed. The matte finish won't reflect light. Choose a color that will blend in for temporary repairs.

For quick repairs, these small rolls of tape don't have a spool so they easily fit into a pocket.

Meets ASME and NRC requirements for use in nuclear power plants. Use to seal end caps on stainless steel pipes, hold labels and signs, and seal ductwork.

Seal and mask rough surfaces such as concrete and stucco with this tape. The adhesive removes cleanly, even after long-term exposure to moisture and UV light.

Temporarily join rolls of paper and film—this tape won't leave residue behind.

Seal foil-jacketed insulation as well as air-conditioning and refrigeration systems with this conformable aluminum tape.

Seal fiberglass duct and insulation that's faced with an all-service jacket (ASJ). Tape is reinforced with fiberglass.

Made of polyester plastic, this tape resists tearing in high-temperature masking jobs, such as on circuit boards and when powder coating.

Use this solvent-resistant plastic tape for anodizing and electroplating applications.

Aluminum foil is laminated to a tough fiberglass cloth to form a high-strength, reflective tape that resists temperatures up to 500° F. Use it for flame-spray masking and wire harness heat shielding.

Protect screen-printed graphics during high-temperature laminating and molding.

Use these convenient cut shapes to mask holes, fastener heads, and small areas while soldering.

Use this crepe paper tape for sharp paint lines.

This tubular foam tape compresses to fill the gaps around door jambs and other openings that flat masking tape can't.

Brush on this liquid to mask small surfaces and irregular shapes.

The adhesive on this crepe paper tape won't damage painted and finished surfaces.

Often used for masking vehicles when painting, this extra-wide tape clings to surfaces and seals off the covered area. It comes in a dispenser with a cutting blade.

This vinyl tape meets clean room requirements and won't leave residue behind. It comes sealed in a plastic bag.

Made to the highest standards for cleanliness, this tape meets clean room requirements. It releases minimal contaminants, leaves no residue behind, and comes sealed in a plastic bag. Use it to mark hazardous items or areas.

Protect impact-prone surfaces from scratches, chips, and abrasion with this thick, conformable tape.

In addition to resisting harsh chemicals, this tape withstands moisture, abrasion, and repeated impact.

Use this UV-resistant tape to temporarily protect smooth plastic, metal, and glass surfaces.

Easy to apply and remove, this film tape protects touch screens and other delicate parts during manufacturing and shipping.

Providing all-weather corrosion protection, this vinyl tape resists salt water, UV light, acids, and alkalies. Use it to wrap pipes and electrical conduit both above and below ground.

Low-pile velvet cushions surfaces and absorbs sound. Use it between parts and in acoustic applications.

Quiet squeaky floor joists and reduce vibration with this foam tape.

Seal out light to mask LEDs and prevent backlight bleed on LCD monitors with this opaque polyester tape.

Also known as Ruby Red lithographer's tape, this semi-clear tape filters out light that can affect photo-sensitive film and equipment.

Protect signs posted on windows, glass, and other surfaces from debris and moisture without obstructing clarity.

No need for adhesive—this tape fuses to itself for a permanent seal and stretches to fit virtually any form. Also known as cold shrink tape.

This chemical-resistant tape has adhesive on both sides.

Use this rubber tape to splice cable in high-voltage applications.

Apply this liquid for a skin-tight protective coating that insulates and resists moisture, acids, and corrosion.

At only 0.0025" thick, this tape combines conformability with durability and abrasion resistance.

Use this tape to modify printed circuit boards, shield components, and prototype wiring-board layout and design.

Made of polyester fabric with a copper/nickel filler, this tape is highly conductive throughout, including the adhesive.

Use this tape to attach components to heat sinks and metal chassis walls in place of screws and other mechanical fasteners. It conducts heat away from sensitive electronics.

A coating on this polyimide tape minimizes ESD (electrostatic discharge) when unwound from the roll and also during removal.

Also known as skived tape, this low-friction tape stretches to conform to irregular surfaces.