For quick repairs, these epoxies begin to harden in 6 minutes or less.

For invisible bond lines, these adhesives dry clear.

To allow time to adjust and position parts, these epoxies remain workable for at least 90 minutes.

Fasten hard-to-bond plastics, such as polypropylene and polyethylene, with these epoxies.

These machinable epoxies are mixed with metal so they can be used to repair cracks and threaded holes.

Bond most materials without the strong odor of other epoxy adhesives.

No need to mix these acrylics—apply adhesive to one surface and activator to the other, then bring surfaces together to bond.

Acrylics bond to the widest range of materials, especially plastics, and require the least amount of surface preparation.

Urethane adhesives are the most flexible, so they bond dissimilar materials and damp vibration.

Also known as super glue, these adhesives bond quickly.

Mixed with rubber for better impact resistance than standard instant-bond adhesives, these adhesives form strong, resilient bonds.

Accommodate joint movement with these adhesives that remain pliable when cured.

To invisibly bond transparent plastics, these adhesives won’t turn cloudy.

In especially damp or humid environments, these adhesives keep their hold.

Use these thick gels, also known as super glue, on vertical surfaces or to fill gaps between parts.

These thick gels fill gaps up to 0.2" wide—the largest of any of our instant-bond adhesives.

Make strong, instant bonds on a variety of materials—but not your skin.

These thin liquids, also known as super glue, flow into small gaps.

These adhesives withstand temperatures up to 480° F.

Invisibly bond glass and transparent plastics.

For flexible bonds that resist cracking, these adhesives stay pliable.

Apply these adhesives on two surfaces, air dry, and then bring together to bond.

Spray a thin, uniform coat of adhesive on one or both surfaces, air dry, and then bring together to form strong bonds.

Spray a coating of this glue to temporarily hold small parts.

Also known as Gorilla Glue, this glue expands to form stronger bonds than other glue.

Apply this glue like tape for a no-mess alternative to liquid adhesives, hot melts, and staples. Also known as adhesive transfer tape.

This general purpose glue tackles a variety of repairs.

This glue withstands temperatures up to 500° F.

These small tabs of pressure-sensitive adhesive offer convenient, no-mess bonding.

When heated, these glue sticks melt and quickly begin to harden. Use them to seal packaging and form other low- to medium-strength bonds.

Prevent threaded fasteners from loosening due to shock and vibration.

Use these threadlockers on fasteners that require occasional fine-tuning, such as set screws.

Keep threaded fasteners from loosening at temperatures up to 450° F.

These low-friction threadlockers harden slowly, allowing ample time to smoothly adjust multiple large bolts for even clamping.

Paste threadlockers are easy to apply and won't drip, even from overhead fasteners.

This gel clings to fasteners to prevent drips.

Wrap this no-mess tape around threaded fasteners up to 30 days before installation.

Apply these threadlockers on fasteners that are already installed—their thin consistency allows them to flow into small gaps.

To speed cure time on coated fasteners, aluminum, stainless steel, or titanium, apply these primers before using threadlocker or retaining compound. They also work with no-mix acrylic adhesives.

Fill gaps up to 0.01" to secure unthreaded cylindrical metal parts such as shafts, bearings, and press-fit assemblies.

Fill gaps up to 0.02" to secure worn unthreaded cylindrical metal parts such as shafts, bearings, and press-fit assemblies.

Made from silicone, these sealants are RTV (room-temperature vulcanizing).

Resistant to mold and mildew, these sealants are well suited to high-humidity environments.

Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Also known as neutral-cure sealants, these won't discolor copper, brass, and concrete.

Apply these sealants in cold temperatures, on wet surfaces, and even through running water.

Clear enough to read through, these UV-resistant sealants allow optimal light transmission for use with solar cells and fiber optics.

These structural sealants combine the mechanical strength of an adhesive with excellent sealing properties and high flexibility.

These sealants are marine grade, so they stand up to water, corrosion from salt spray, mildew, and UV light.

Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Impervious to the swelling effects of oil, fuel, and solvents, use these high-strength sealants to assemble and repair fuel systems and tanks.

These non-sagging sealants will not drip while hardening on vertical and overhead surfaces.