These metric set screws have a rolling ball that swivels 360° to minimize surface damage and allow for slight adjustments without loosening the screw.

Stainless steel set screws have excellent corrosion resistance in most environments.

A wide tip provides more gripping power than standard swivel-tip set screws. To use, remove the tip, thread the screw through the hole, and attach the tip on the other side.

These set screws have a low-profile flat-faced ball tip for use in low-clearance applications.

For maximum contact with angled and uneven surfaces, the tip swivels in all directions. The tip is narrow so it will fit through threaded holes.

Fine threads give you precise control.

Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.

Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.

Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.

Also known as trapezoidal-thread lead screws and nuts.

These metric lead screws and nuts have broad, square threads that are well suited for quick assembly, high clamping forces, and lifting and lowering heavy objects. They're commonly found in hand-powered clamps, vises, grates, doors, and work tables.

Keep your ball screw spinning without the ball nut damaging your system. When the ball nut reaches the stop pin at either end of the ball screw, it disengages and begins to idle.

Also known as single-start ball screws and nuts, these have a single thread that runs the length of the screw. They operate with more torque than fast-travel ball screws and nuts.

Internal ball bearings provide smooth low-friction travel in applications that require high speeds, accurate positioning, and repeatable movement. Also known as single-start metric ball screws and nuts, these have a single thread that runs the length of the screw.

A set of ball bearings reduces friction and secures the end of a metric ball or lead screw.

Mount these two-piece collars anywhere on an Acme lead screw without removing components.

Install these nuts on a rotary shaft to create a linear positioning system without a lead screw. Instead of threads, a set of angled ball bearings drives the nut along a shaft as it spins.

Made of yellow zinc-plated steel, these metric leveling mounts are more corrosion resistant than nickel-plated steel leveling mounts.

An economical choice for applications in corrosive environments that don't require high load capacities, these mounts have a plastic base.

Made of 303 stainless steel, these metric mounts resist corrosion from water and most chemicals.

Made entirely of 316 stainless steel, these mounts have superior corrosion resistance.

Broader, stronger threads enable faster adjustments and higher load capacities than standard V-shaped threads.

Well-suited to damp environments, these metric mounts have a stainless steel stud and nut for corrosion resistance.

Punch-out holes in the base let you bolt down these metric mounts to keep your equipment stationary.

Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance.

Black-oxide steel has a dull shine for areas where appearance is a concern.

Made of 303 stainless steel, these mounts resist corrosion from water and most chemicals.

Made entirely of 316 stainless steel, these mounts are our most resistant to corrosion from chemicals, solvents, and water.

Well-suited to damp environments, these mounts have a stainless steel nut for excellent corrosion resistance.

Made entirely of plastic, these mounts are resistant to oil and won't scratch your mounting surface.

Use these metric mounts on heavy machines and equipment.

Made of 303 stainless steel, these metric mounts resist corrosion from water and most chemicals.

Meant for light duty applications, these mounts are not rated for capacity.

Often used on wobbly tables, these mounts automatically adjust up to 5/16" to compensate for uneven floors.

Able to withstand temperatures up to 350° F, these have the highest maximum temperature of our plastic mounts.

Thread these mounts into machinery to level them on uneven floors in sanitary environments such as food-processing areas.

Higher deflection ratings translate to greater vibration and shock isolation.

Higher deflection ratings translate to greater vibration and shock isolation.

Higher deflection ratings translate to greater vibration and shock isolation than our other vibration-damping leveling mounts.