Once aftercoolers and separators have removed the bulk of the water, use these dryers to remove any remaining moisture in your air line.

For use with Norgren modular compressed air systems, once aftercoolers and separators have removed the bulk of the water, use one of these desiccant-filled dryers to remove any remaining moisture in your air line.

With a clear polycarbonate bowl that’s visible from all angles and silica gel desiccant that changes from blue to pink, it’s easy to see when it’s time to change the cartridge on these dryer/filters and dryer/filter/regulators.

These dryer/filters have a clay desiccant that removes moisture, oil, and particles, so there’s no need to install a separate filter and dryer. Once aftercoolers and separators have removed the bulk of the water, they remove any remaining moisture in your air line.

Cool air through refrigeration to condense water vapor.

A float-operated drain valve on these separators automatically opens when the bowl begins to fill. The first step in water removal, use one of these separators to remove the large amount of water as compressed air cools.

In addition to removing large amounts of water, these separators also remove particles and oil droplets. Place them after your compressor and aftercooler, or at the point of use in applications that don't require an aftercooler.

Also known as regenerative blowers, use these to produce high-flow compressed air with low pressure or vacuum to operate pump drives, lift tables, and conveying systems.

Blow air backward to clean out the inside of pipes, tubes, and channels without pushing debris into your system.

Control consumption and noise by adjusting the airflow.

Extend these telescoping nozzles to increase your reach.

The flat nozzle tip distributes air over a wider area than focused-airflow nozzles.

Nozzles are attached to a flexible tube or hose that bends and holds its shape until you reposition it.

Choose a base, hose, and nozzle for a custom setup.

Operate a blowgun without disconnecting your air tool—these guns fit between the tool and air hose. Good for blowing away debris after using an air-powered sander or grinder.

Also known as air-shield and safety-shield blowguns, a center airstream blows away debris while an outer air curtain deflects flying chips and dust.

The lightweight plastic construction makes these blowguns more comfortable to hold than metal.

Compact enough to carry with you, these guns have a built-in quick-disconnect hose coupling for easy connection to an air line.

Two inlets allow connection to air lines above or below. Use the top inlet when the blowgun is suspended from an overhead hose and the bottom inlet for bench and floor hoses.

Designed to reduce noise, these blowguns are quieter than similar standard guns.

Also known as air-shield and safety-shield blowguns, an outer air curtain deflects flying chips and dust while the center airstream blows away debris.

The extra length lets you access hard-to-reach areas.

Maximize comfort and minimize strain with these lightweight guns.

The most powerful blowguns we sell, these use compressed air to clean and blow debris.

The extra length lets you access hard-to-reach areas.

Air flows out of the side of the nozzle to clean air filters, radiators, and inside recesses.

These tubular holders have open ends. Slide a blowgun inside for storage.

Clean surfaces without transferring dust or moisture from the air hose. These blowguns have a replaceable filter that traps particles such as rust and smoke and absorbs moisture.

These guns provide more than three times the airflow of standard static-eliminating blowguns.

Safely blow dust and debris off your clothes. These blowers are a safer alternative to compressed air and help you meet OSHA regulations.

Create a sheet of high-velocity air.

Secure an air knife to the bracket and position where needed. Two swiveling joints allow 360° movement.

Also known as air wipes, these use a 360° airstream to blow off, dry, clean, and cool tubes, cables, extruded shapes, and hoses.

Attach to a blower for high-speed airflow at low pressure.

Combine high-volume airflow with low-heat output for warming and drying.

Use these blowers for production drying, heat shrinking, and other applications requiring heat over 1000°F.

Clean parts with compressed air without propelling fluids and debris all over your shop. These vacuum/blowers quickly blow coolant, oil, and chips off your parts while a vacuum sucks them into a removable drum for recycling or disposing of them.