Designed to be mounted inline, these valves can be installed in an easy-to-reach location along your line. They control the speed of air-powered equipment by adjusting the volume of airflow.

Designed to be mounted inline, these valves can be placed in an easy-to-reach location along your line to control the speed of air-powered equipment by adjusting the volume of airflow. A numeric indicator provides a relative measure of airflow, similar to the volume dial on a speaker, so it's easy to set the same flow rate with each use.

A fine-adjustment dial allows tighter control of airflow and cylinder speed than other flow control valves. They control the speed of air-powered equipment by adjusting the volume of airflow entering or exiting.

Mount these valves directly to cylinder ports, eliminating additional tubing between the cylinder and valve for better control than inline valves. Made of plastic and stainless steel parts, they have excellent corrosion resistance. They control the speed of air-powered equipment by adjusting the volume of airflow.

These valves handle pressure up to 265 psi. They control the speed of air-powered equipment by adjusting the volume of airflow entering or exiting.

Adjust airflow equally in both directions. These valves regulate the speed of airflow as it enters and exits equipment. They're often used to control the extension and retraction speed of an air cylinder at the same time.

Prevent damage to your equipment by limiting startup airflow and then gradually raising the airflow rate to operating levels.

Control the flow of exhaust air while also regulating the exhaust air speed. These valves dump exhaust air to the atmosphere without routing it back through a directional control valve. The 90° elbow shape allows you to install them in tight spaces. Also known as quick exhaust valves.

A muffler reduces exhaust noise. Valves allow airflow into your equipment and then quickly dump exhaust air to the atmosphere without routing it back through a directional control valve to speed up the movement of equipment. Also known as quick exhaust valves.

Choose the pressure range you need. When these valves receive an air signal, they quickly dump exhaust air to the atmosphere without routing it back through a directional control valve to speed up the movement of equipment. They're often used with air compressors that require continuous operation. Also known as quick exhaust valves.

Since both hands are required to simultaneously press the buttons, these valves protect workers from accidental machinery start-up. They create two actions, such as extending and then retracting a double-acting cylinder.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. Also known as 4/3 closed-center valves, they create two actions, such as extracting and then retracting a double-acting cylinder.

Because they require a key to operate, you can limit who is able to adjust these valves. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/2 valves.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/3 exhaust center valves.

To prevent accidental start-up, these valves can be locked in their off position with a padlock. They create one action, such as extending a cylinder.

The push buttons that operate these valves are separate from the logic unit, allowing you to position them away from machinery. Since both hands are required to simultaneously press the buttons, they protect workers from accidental machinery start-up. They create one action, such as extending a cylinder.

Since both hands are required to simultaneously press the buttons, these valves protect workers from accidental machinery start-up. They create one action, such as extending a cylinder.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 5/2 valves, they actuate when voltage is applied to the electrical connection.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Also known as 4-way valves, these valves create two actions, such as extending and then retracting a double-acting cylinder. Apply voltage to the electrical connection to actuate.

Run through equipment cycles up to 30% faster than with standard valves. These valves shift between flow positions in 1.7 ms. Also known as 3/2 valves, they create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate.

Create two actions at the same time, such as extending two single-acting cylinders at once. Apply voltage to the electrical connection to actuate. Also known as pressure center valves.

Rated IP69K, these valves withstand high-pressure, high-temperature washdowns. Their smooth design keeps out dust, dirt, and contaminants, making them easier to keep clean. Apply voltage to the electrical connection to actuate.

With two 3-way integrated solenoid valves, these electrically controlled valves direct airflow to end-of-arm tools that don’t require vacuum suction, such as pick-and-place grippers. Also known as 3/2 valves, each of the two solenoid valves directs air to a different port.

A simple automation solution that requires no programming, these valves are activated when an object, such as a box rolling on a conveyor, pushes the actuator. They create one action, such as extending a cylinder. Also known as 3-way and 3/2 valves.

These valves create one action, such as extending a cylinder. Use your foot to operate them, leaving your hands free to perform other tasks. Also known as 3-way or 3/2 valves.

Also known as 4-way and 4/2 valves, these valves create two actions, such as extending and then retracting a cylinder. Use your foot to operate them, leaving your hands free to perform other tasks.

Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as pilot valves and 4-way valves, they use an air signal to actuate, so they're good for environments where electrical use may be dangerous.

Mix and match valve styles on one manifold to meet your control needs. Mount multiple valves to a manifold to reduce piping requirements and create multiple actions from a single pressure input.

These valves have a muffler to reduce exhaust noise. A padlock locks the handle in the shut-off position so you can disconnect air tools safely.

Control flow in two directions from a single source—these valves have two balls for independent control and shut-off of each outlet.

Also known as solenoid valves, these valves are operated by an electrical signal to turn airflow on or off.

With two 2-way integrated solenoid valves, these electrically controlled valves direct airflow to venturi pumps, which generate the suction you need to run end-of-arm tools, such as vacuum cups.

Also known as air fuses, these valves close automatically to turn airflow off when air volume exceeds the shut-off flow rate.

Prevent air from escaping an air storage tank when the air compressor is not running. These valves open to allow flow into the tank and close when flow stops or reverses direction.

Convert a continuous stream of air into a series of quick pulses, reducing air consumption by up to 50% and improving performance in air-blowing applications such as cleaning and drying.

Adjust and maintain the pressure of your compressed air.

Adjust and maintain the pressure of your compressed air.

Adjust and maintain the pressure of your compressed air.

Adjust and maintain the pressure of your compressed air.

A lower profile than our other compressed air regulators makes these regulators a better fit in tight spots.

Prevent unauthorized adjustment and unintentional pressure changes with these regulators.

Cleaned and double bagged in an ISO Class 3 and Fed. Spec. Class 1 clean room for protection from contamination, these regulators are suitable for use in clean rooms.

Mount these regulators to a 35 mm DIN rail with the included brackets.

A pressure-calibrated dial allows for easy adjustments to outlet pressure in high-flow applications.

Fit these regulators in tight spaces to adjust and maintain air pressure in sensitive applications where constant, consistent pressure is important.

Mount these regulators to a 35 mm DIN rail or a wall with one of the two included brackets.

Mount these regulators to a 35 mm DIN rail with the included bracket.

View and control output pressure remotely and at the source.

Use a low-flow air pilot signal with an air supply to produce flow up to 50 cfm to actuate valves and other air-powered system components.

Also known as Monday-morning valves, these valves slowly introduce pressure to reduce surge damage during start-up.

Also known as Monday-morning valves, these valves slowly introduce pressure to reduce surge damage during start-up.

Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Designed for high-pressure instrumentation applications, these valves are rated for up to 10,000 psi and have a hex nut and threads below the handle for panel mounting. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For installation in instrument panels, these valves have a hex nut and threads below the handle. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Rated for nearly twice the maximum temperature of standard threaded precision flow-adjustment valves, these can handle up to 700° F. They’re for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Also known as block and bleed valves, these have a vent port that allows you to remove instrumentation equipment attached to the valve without depressurizing your line. Turn the handle to shut off flow and remove the vent port plug to drain liquid trapped in the valve. Use them with water, oil, air, and inert gas. These valves adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Barbs grip onto tubing, providing a secure hold. These valves are for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

A compression sleeve bites into tubing as you tighten the nut, forming a strong seal. These valves are for use with air. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. Designed for use in food and beverage tubing lines, they adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.